• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM E 1399/E1399M : 1997 : R2017

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Cyclic Movement and Measuring the Minimum and Maximum Joint Widths of Architectural Joint Systems
Available format(s)

Hardcopy , PDF

Superseded date

11-10-2022

Language(s)

English

Published date

06-09-2017

CONTAINED IN VOL. 04.11, 2017 Defines testing procedures for architectural joint systems.

1.1This test method covers testing procedures for architectural joint systems. This test method is intended for the following uses for architectural joint systems:

1.1.1To verify movement capability information supplied to the user by the producer,

1.1.2To standardize comparison of movement capability by relating it to specified nominal joint widths,

1.1.3To determine the cyclic movement capability between specified minimum and maximum joint widths without visual deleterious effects, and

1.1.4To provide the user with graphic information, drawings or pictures in the test report, depicting them at minimum, maximum, and nominal joint widths during cycling.

1.2This test method is intended to be used only as part of a specification or acceptance criterion due to the limited movements tested.

1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
E 06
DevelopmentNote
Supersedes ASTM E 1399. (09/2013)
DocumentType
Test Method
Pages
6
ProductNote
Reconfirmed 2017
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM E 1612/E1612M : 1994 : R2022 Standard Specification for Preformed Architectural Compression Seals for Buildings and Parking Structures
ASTM E 1783/E1783M : 1996 : R2017 Standard Specification for Preformed Architectural Strip Seals for Buildings and Parking Structures
ASTM E 3037 : 2020 Standard Test Method for Measuring Relative Movement Capabilities of Through-Penetration Firestop Systems

ASTM D 1079 : 2018 : EDT 1 Standard Terminology Relating to Roofing and Waterproofing
ASTM E 631 : 2015 : REDLINE Standard Terminology of Building Constructions
ASTM D 1079 : 2008 : REV A Standard Terminology Relating to Roofing and Waterproofing
ASTM C 794 : 2018 Standard Test Method for Adhesion-in-Peel of Elastomeric Joint Sealants
ASTM D 1079 : 2016 Standard Terminology Relating to Roofing and Waterproofing
ASTM C 719 : 2022 Standard Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle)
ASTM D 1079 : 2006 Terminology Relating to Roofing and Waterproofing
ASTM D 1079 : 2020 Standard Terminology Relating to Roofing and Waterproofing
ASTM C 962 : 86 E1 GUIDE FOR USE OF ELASTOMERIC JOINT SEALANTS
ASTM D 1079 : 2013 Standard Terminology Relating to Roofing and Waterproofing
ASTM D 1079 : 2007 : REV A Terminology Relating to Roofing and Waterproofing
ASTM D 1079 : 2010 Standard Terminology Relating to Roofing and Waterproofing
IEEE/ASTM SI_10-2010 American National Standard for Metric Practice
ASTM D 1079 : 2018 Standard Terminology Relating to Roofing and Waterproofing
ASTM C 794 : 2018 : R2022 Standard Test Method for Adhesion-in-Peel of Elastomeric Joint Sealants
ASTM D 1079 : 2005 : REV A Terminology Relating to Roofing and Waterproofing
ASTM C 719 : 2014 : R2019 Standard Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle)
ASTM D 1079 : 2002 Standard Terminology Relating to Roofing, Waterproofing, and Bituminous Materials
ASTM D 1079 : 2001 Standard Terminology Relating to Roofing, Waterproofing, and Bituminous Materials
ASTM C 962 : 1988 : EDT 1 Guide for Use of Elastomeric Joint Sealants
ASTM D 1079 : 2000 : REV A Standard Terminology Relating to Roofing, Waterproofing, and Bituminous Materials
ASTM D 1079 : 2013 : EDT 1 Standard Terminology Relating to Roofing and Waterproofing
ASTM D 1079 : 2009 Standard Terminology Relating to Roofing and Waterproofing

View more information
£62.61
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.