We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • ASTM E 1851 : 2015

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    Standard Test Method for Electromagnetic Shielding Effectiveness of Durable Rigid Wall Relocatable Structures

    Available format(s):  Hardcopy, PDF

    Superseded date:  15-02-2021

    Language(s):  English

    Published date:  16-09-2015

    Publisher:  American Society for Testing and Materials

    Add to Watchlist

    Add To Cart

    Scope - (Show below) - (Hide below)

    1.1This test method covers the determination of the electromagnetic shielding effectiveness of durable relocatable shielded enclosures.

    1.1.1The intended application of this test method is for virgin shielded enclosures that do not have any equipment or equipment racks. It is recommended that tests be conducted before the interior finish work begins. However, the shield assembly including all enclosure penetrations shall be completed and required penetration protection devices shall be installed in accordance with the design specification. The test method can also be used on existing shielded enclosures after repair work is done to verify workmanship, but it may be necessary to remove equipment or equipment racks to gain access to a test area.

    1.1.2The test procedures delineated in this document are comprehensive and may require several days to complete for a room-size shielded enclosure. A user can apply this test method for a first article test that requires proof of concept and validation of design and fabrication technique. Appendix X2 provides guidance on choosing test points so shielding effectiveness tests on a room-size shielded enclosure may be completed in about one-half day for which it applies to shielded enclosures coming off an assembly line.

    1.2This test method is for use in the following frequency ranges: 140 to 160 kHz, 14 to 16 MHz, 300 to 500 MHz, 900 to 1000 MHz, and 8.5 to 10.5 GHz. Specific test frequencies within these ranges are required (see 11.1.1 and 11.2.1). Additional measurements in the range of 10 kHz to 10.5 GHz may be performed. For specific applications, the frequency range may be extended from 50 Hz to 40 GHz. Appendix X1 provides guidance on selecting measurement frequencies.

    1.3This test method is not applicable to individual components such as separate walls, floors, ceilings, or shielded racks.

    1.4This standard may involve hazardous materials, operations, equipment, or any combination.

    1.5The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.

    1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    General Product Information - (Show below) - (Hide below)

    Committee E 06
    Document Type Test Method
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    ASTM E 1925 : 2018 Specification for Engineering and Design Criteria for Rigid Wall Relocatable Structures
    ASTM E 1975 : 2018 Standard Specification for Shelter, Electrical, Equipment S-280/G
    ASTM E 2377 : 2018 Standard Specification for Shelter, Electrical Equipment, Lightweight

    Standards Referencing This Book - (Show below) - (Hide below)

    ASTM E 1749 : 2000 Standard Terminology Relating to Rigid Wall Relocatable Shelters
    ASTM E 1749 : 2018 Standard Terminology Relating to Rigid Wall Relocatable Shelters
    ASTM E 1749 : 2005 Standard Terminology Relating to Rigid Wall Relocatable Shelters
    ASTM E 1749 : 2010 Standard Terminology Relating to Rigid Wall Relocatable Shelters
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective