• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM E 215 : 2016 : REDLINE

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Practice for Standardizing Equipment and Electromagnetic Examination of Seamless Aluminum-Alloy Tube
Available format(s)

PDF

Superseded date

23-08-2022

Language(s)

English

Published date

13-01-2017

CONTAINED IN VOL. 03.03, 2017 Defines a guide for standardizing eddy-current equipment employed in the examination of seamless aluminum-alloy tube.

1.1This practice2 is for standardizing eddy current equipment employed in the examination of seamless aluminum-alloy tube. Artificial discontinuities consisting of flat-bottomed or through holes, or both, are employed as the means of standardizing the eddy current system. General requirements for eddy current examination procedures are included.

1.2Procedures for fabrication of reference standards are given in Appendixes X1.1 and X2.1.

1.3This practice is intended for the examination of tubular products having nominal diameters up to 4 in. [101.6 mm] and wall thicknesses up to the standard depth of penetration (SDP) of eddy currents for the particular alloy (conductivity) being examined and the examination frequency being used.

Note 1:This practice may also be used for larger diameters or heavier walls up to the effective depth of penetration (EDP) of eddy currents as long as adequate resolution is obtained and as specified by the using party or parties.

1.4This practice does not establish acceptance criteria. They must be established by the using party or parties.

1.5The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.6This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
E 07
DocumentType
Redline
Pages
11
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

MIL I 6870 : E INSPECTION PROGRAM REQUIREMENTS NONDESTRUCTIVE FOR AIRCRAFT AND MISSILE MATERIALS AND PARTS
ASTM B 234M : 2017 : REDLINE Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Surface Condensers, Evaporators, and Heat Exchangers (Metric)
SAE AMS 4083 : 2012 ALUMINUM ALLOY TUBING, HYDRAULIC, SEAMLESS, DRAWN, ROUND, 1.0MG - 0.60SI - 0.28CU - 0.20CR (6061-T6), SOLUTION AND PRECIPITATION HEAT TREATED
14/30301152 DC : 0 BS EN 12392 - ALUMINIUM AND ALUMINIUM ALLOYS - WROUGHT PRODUCTS AND CAST PRODUCTS - SPECIAL REQUIREMENTS FOR PRODUCTS INTENDED FOR THE PRODUCTION OF PRESSURE EQUIPMENT
BS 4L 100:1993 Procedure for inspection, testing and acceptance of wrought aluminium and aluminium alloys
PREN 12392 : DRAFT 2014 ALUMINIUM AND ALUMINIUM ALLOYS - WROUGHT PRODUCTS AND CAST PRODUCTS - SPECIAL REQUIREMENTS FOR PRODUCTS INTENDED FOR THE PRODUCTION OF PRESSURE EQUIPMENT
SAE AMSWWT700B:2001(S2018) TUBE, ALUMINIUM AND ALUMINIUM ALLOY, DRAWN, SEAMLESS, GENERAL SPECIFICATION FOR
ASTM E 543 : 2015 : REDLINE Standard Specification for Agencies Performing Nondestructive Testing
ASTM B 491/B491M : 2015 : REDLINE Standard Specification for Aluminum and Aluminum-Alloy Extruded Round Tubes for General-Purpose Applications
EN 12392:2016 Aluminium and aluminium alloys - Wrought products and cast products - Special requirements for products intended for the production of pressure equipment
SAE AMS 4086 : 2015 ALUMINUM ALLOY, DRAWN, ROUND, SEAMLESS HYDRAULIC TUBING, 4.4CU - 1.5MG - 0.6MN (2024-T3), SOLUTION HEAT TREATED, COLD WORKED AND NATURALLY AGED
SAE AMS 4081 : 2014 ALUMINUM ALLOY TUBING, HYDRAULIC, SEAMLESS, DRAWN, ROUND, 1.0MG - 0.60SI - 0.28CU - 0.20CR (6061-T4) SOLUTION HEAT TREATED AND NATURALLY AGED
BS 4L 56:1986 Specification for tube of aluminium-2¼% magnesium alloy (temper designation-O) (seamless: tested hydraulically) (not exceeding 12 mm wall thickness)
BS 4L 54:1986 Specification for tube of 99% aluminium (cold drawn: seamless: tested hydraulically) (not exceeding 12 mm wall thickness)
SAE J 425 : 2018 ELECTROMAGNETIC TESTING BY EDDY CURRENT METHODS
I.S. EN 12392:2016 ALUMINIUM AND ALUMINIUM ALLOYS - WROUGHT PRODUCTS AND CAST PRODUCTS - SPECIAL REQUIREMENTS FOR PRODUCTS INTENDED FOR THE PRODUCTION OF PRESSURE EQUIPMENT
ASTM B 483/B483M : 2013 Standard Specification for Aluminum and Aluminum-Alloy Drawn Pipe for General Purpose Applications
MIL-T-7081 Revision D:1965 TUBE, ALUMINUM ALLOY, SEAMLESS, ROUND, DRAWN, 6061, AIRCRAFT HYDRAULIC QUALITY
ASTM B 483/B483M : 2013 : EDT 1 Standard Specification for Aluminum and Aluminum-Alloy Drawn Tube and Drawn Pipe for General Purpose Applications
DIN EN 12392:2016-08 Aluminium and aluminium alloys - Wrought products and cast products - Special requirements for products intended for the production of pressure equipment
MIL-HDBK-6870 Revision B:2012 NONDESTRUCTIVE INSPECTION PROGRAM REQUIREMENTS FOR AIRCRAFT AND MISSILE MATERIALS AND PARTS
BS L 118:1975 Specification for tube of aluminium-magnesium-silicon-copper-chromium alloy (solution treated and artificially aged: tested hydraulically) (not exceeding 10 mm thickness) (Mg 1.0, Si 0.6, Cu 0.28, Cr 0.2)
SAE AMS 4071 : 2017 ALUMINUM ALLOY, DRAWN, ROUND, SEAMLESS HYDRAULIC TUBING, 2.5MG - 0.25CR (5052-O), ANNEALED
MIL-T-50777 Revision A:1990 TUBE, ALUMINUM ALLOY 2024 SEAMLESS (FOR PROPELLANT ACTUATED DEVICES)
BS 5L100(2011) : 2011 PROCEDURE FOR INSPECTION, TESTING AND ACCEPTANCE OF WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS
ASTM E 426 : 2016 : REDLINE Standard Practice for Electromagnetic (Eddy Current) Examination of Seamless and Welded Tubular Products, Titanium, Austenitic Stainless Steel and Similar Alloys
BS EN 12392:2016 Aluminium and aluminium alloys. Wrought products and cast products. Special requirements for products intended for the production of pressure equipment
ASTM B 234 : 2017 : REDLINE Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Surface Condensers, Evaporators, and Heat Exchangers

ASNT SNT TC 1A : 2016 TOPICAL OUTLINES FOR QUALIFICATION OF NONDESTRUCTIVE TESTING PERSONNEL
ISO 9712:2012 Non-destructive testing Qualification and certification of NDT personnel
NAS410:2003 NAS CERTIFICATION & QUALIFICATION OF NONDESTRUCTIVE TEST PERSONNEL
FED-STD-245 Revision E:1985 TOLERANCES FOR ALUMINUM ALLOY AND MAGNESIUM ALLOY WROUGHT PRODUCTS
ASNT CP 189 : 2016 QUALIFICATION AND CERTIFICATION OF NONDESTRUCTIVE TESTING PERSONNEL
ASTM E 543 : 2015 : REDLINE Standard Specification for Agencies Performing Nondestructive Testing

View more information
£69.29
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.