• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM E 3024/E3024M : 2016

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Practice for Magnetic Particle Testing for General Industry
Available format(s)

Hardcopy , PDF

Superseded date

15-07-2019

Language(s)

English

Published date

01-07-2016

CONTAINED IN VOL. 03.04, 2017 Specifies minimum requirements for magnetic particle testing used for the detection of surface or slightly subsurface discontinuities in ferromagnetic material.

1.1This practice establishes minimum requirements for magnetic particle testing used for the detection of surface or slightly subsurface discontinuities in ferromagnetic material. This standard is intended for industrial applications. Refer to Practice E1444/E1444M for aerospace applications. Guide E709 may be used in conjunction with this practice as a tutorial.

1.2The magnetic particle testing method is used to detect cracks, laps, seams, inclusions, and other discontinuities on or near the surface of ferromagnetic materials. Magnetic particle testing may be applied to raw material, billets, finished and semi-finished materials, welds, and in-service parts. Magnetic particle testing is not applicable to non-ferromagnetic metals and alloys such as austenitic stainless steels. See Appendix X1 for additional information.

1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.3.1This standard is a combined standard, an ASTM standard in which rationalized SI units and inch-pound units are included in the same standard, with each system of units to be regarded separately as standard.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
E 07
DocumentType
Standard Practice
Pages
19
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

SAE AMS 3040 : 2014 MAGNETIC PARTICLES, NONFLUORESCENT, DRY METHOD
ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories
FED-STD-313 Revision D:1996 MATERIAL SAFETY DATA, TRANSPORTATION DATA AND DISPOSAL DATA FOR HAZARDOUS MATERIALS FURNISHED TO GOVERNMENT ACTIVITIES
SAE AMS 3045 : 2014 MAGNETIC PARTICLES, FLUORESCENT, WET METHOD, OIL VEHICLE, READY-TO-USE
ASNT SNT TC 1A : 2016 TOPICAL OUTLINES FOR QUALIFICATION OF NONDESTRUCTIVE TESTING PERSONNEL
ISO 9712:2012 Non-destructive testing Qualification and certification of NDT personnel
ANSI/NCSL Z540 3 : 2006(R2013) REQUIREMENTS FOR THE CALIBRATION OF MEASURING AND TEST EQUIPMENT
SAE AMS 2641 : 2015 VEHICLE, MAGNETIC PARTICLE INSPECTION, PETROLEUM BASE
SAE AMS 3042 : 2014 MAGNETIC PARTICLES, NONFLUORESCENT, WET METHOD, DRY POWDER
SAE AMS 3043 : 2014 MAGNETIC PARTICLES, NONFLUORESCENT, WET METHOD, OIL VEHICLE, AEROSOL PACKAGED
SAE AS 4792 : 2013 WATER CONDITIONING AGENTS FOR AQUEOUS MAGNETIC PARTICLE INSPECTION
SAE AMS 3041 : 2014 MAGNETIC PARTICLES, NONFLUORESCENT, WET METHOD, OIL VEHICLE, READY-TO-USE
SAE AMS 3044G : 2014 MAGNETIC PARTICLES, FLUORESCENT, WET METHOD, DRY POWDER
SAE AMS I 83387 : 2016 INSPECTION PROCESS, MAGNETIC RUBBER
ASNT CP 189 : 2016 QUALIFICATION AND CERTIFICATION OF NONDESTRUCTIVE TESTING PERSONNEL
CFR 29(PT1910.1000 TO END) : 0 LABOR - OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR
ISO 10012:2003 Measurement management systems — Requirements for measurement processes and measuring equipment
ASTM E 2297 : 2015 : REDLINE Standard Guide for Use of UV-A and Visible Light Sources and Meters used in the Liquid Penetrant and Magnetic Particle Methods
SAE AMS 5062 : 2013 STEEL, LOW CARBON, BARS, FORGINGS, TUBING, SHEET, STRIP, AND PLATE, 0.25 CARBON, MAXIMUM
SAE AS 5371 : 1998 REFERENCE STANDARDS NOTCHED SHIMS FOR MAGNETIC PARTICLE INSPECTION
ASTM E 543 : 2015 : REDLINE Standard Specification for Agencies Performing Nondestructive Testing
ASTM E 709 : 2015 : REDLINE Standard Guide for Magnetic Particle Testing
ASTM E 3022 : 2015 Standard Practice for Measurement of Emission Characteristics and Requirements for LED UV-A Lamps Used in Fluorescent Penetrant and Magnetic Particle Testing
SAE AMS 3046 : 2014 MAGNETIC PARTICLES, FLUORESCENT, WET METHOD, OIL VEHICLE, AEROSOL PACKAGED
A-A-59230 Base Document:1998 FLUID, MAGNETIC PARTICLE INSPECTION, SUSPENSION

View more information
£69.29
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.