ASTM E 331 : 2000
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
14-08-2016
English
10-10-2000
CONTAINED IN VOL. 04.11, 2016 Defines the determination of the resistance of exterior windows, curtain walls, skylights, and doors to water penetration when water is applied to the outdoor face and exposed edges simultaneously with a uniform static air pressure at the outdoor face higher than the pressure at the indoor face.
1.1 This test method covers the determination of the resistance of exterior windows, curtain walls, skylights, and doors to water penetration when water is applied to the outdoor face and exposed edges simultaneously with a uniform static air pressure at the outdoor face higher than the pressure at the indoor face.
1.2 This test method is applicable to any curtain-wall area or to windows, skylights, or doors alone.
1.3 This test method addresses water penetration through a manufactured assembly. Water that penetrates the assembly, but does not result in a failure as defined herein, may have adverse effects on the performance of contained materials such as sealants and insulating or laminated glass. This test method does not address these issues.
1.4 The proper use of this test method requires a knowledge of the principles of pressure measurement.
1.5 The values stated in SI units are to be regarded as the standard. The inch-pound equivalents of SI units may be approximate.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| Committee |
E 06
|
| DocumentType |
Test Method
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM D 4099 : 1995 | Standard Specification for Poly(Vinyl Choride)(PVC) Prime Windows and Sliding Glass Doors (Withdrawn 1999) |
| ASTM E 1646 : 1995 : R2018 | Standard Test Method for Water Penetration of Exterior Metal Roof Panel Systems by Uniform Static Air Pressure Difference |
| ASTM E 1089 : 1986 : R1995 | Standard Test Method for Water Penetration of Flat Plate Solar Collectors by Uniform Static Air Pressure Difference |
| ASTM E 2099 : 2000 : R2007 | Standard Practice for the Specification and Evaluation of Pre-Construction Laboratory Mockups of Exterior Wall Systems |
| ASTM E 2112 : 2007 : R2016 | Standard Practice for Installation of Exterior Windows, Doors and Skylights |
| ASTM C 964 : 2007 : R2012 | Standard Guide for Lock-Strip Gasket Glazing |
| ASTM E 1089 : 1986 : R2001 | Standard Test Method for Water Penetration of Flat Plate Solar Collectors by Uniform Static Air Pressure Difference |
| ICC 2009 INT. RESI.CODE & COMM.-I1 : 2009 | 2009 INTERNATIONAL RESIDENTIAL CODE & COMMENTARY - VOLUME 2: CHAPTERS 12 TO 44 |
| MIL-B-28658 Revision E:1991 | BUILDING COMPONENTS, PANELIZED, PREFABRICATED, READY-CUT, RELOCATABLE |
| ASTM E 1089 : 1986 : R2007 | Standard Test Method for Water Penetration of Flat Plate Solar Collectors by Uniform Static Air Pressure Difference (Withdrawn 2013) |
| ASTM E 1677 : 2011 : REDLINE | SPECIFICATION FOR AIR BARRIER (AB) MATERIAL OR SYSTEM FOR LOW-RISE FRAMED BUILDING WALLS |
| ASCE 30 00 : 2000 | GUIDELINE FOR CONDITION ASSESSMENT OF THE BUILDING ENVELOPE |
| ASTM E 2570/E2570M : 2007 : R2019 | Standard Test Methods for Evaluating Water-Resistive Barrier (WRB) Coatings Used under Exterior Insulation and Finish Systems (EIFS) or EIFS with Drainage |
| ASTM E 241 : 2009 | Standard Guide for Limiting Water-Induced Damage to Buildings |
| ASTM E 2273 : 2003 | Standard Test Method for Determining the Drainage Efficiency of Exterior Insulation and Finish Systems (EIFS) Clad Wall Assemblies |
| ICC IRC Code and Commentary Volume 1 : 2015 | IRC® Code and Commentary, Volume 1 |
| ICC 2012 INTERNATIONAL BUILDING CODE : 2012 | INTERNATIONAL BUILDING CODE |
| ASTM E 1646 : 1995 | Standard Test Method for Water Penetration of Exterior Metal Roof Panel Systems by Uniform Static Air Pressure Difference |
| ASTM E 2264 : 2005 : R2013 | Standard Practice for Determining the Effects of Temperature Cycling on Fenestration Products |
| ASTM E 2099 : 2000 : R2014 : EDT 1 | Standard Practice for the Specification and Evaluation of Pre-Construction Laboratory Mockups of Exterior Wall Systems |
| ASTM E 2570 : 2007 | Standard Test Methods for Evaluating Water-Resistive Barrier (WRB) Coatings Used under Exterior Insulation and Finish Systems (EIFS) or EIFS with Drainage |
| ASTM E 2266 : 2011 : REDLINE | Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion |
| ASTM E 241 : 2009 : R2014 : EDT 1 | Standard Guide for Limiting Water-Induced Damage to Buildings |
| ASTM E 2273 : 2003 : R2011 | Standard Test Method for Determining the Drainage Efficiency of Exterior Insulation and Finish Systems (EIFS) Clad Wall Assemblies |
| ASTM D 4973 : 1993 | Specification for White Rigid Poly(Vinyl Chloride)(PVC) Insulating Storm Windows (Withdrawn 1999) |
| CSA Z320 : 2011 : R2016 | BUILDING COMMISSIONING |
| ICC IRC CODE AND COMMENTARY VOLUME 2 : 2015 | IRC® Code and Commentary, Volume 2 |
| ICC IBC CODE AND COMMENTARY VOLUME 2 : 2015 | IBC® Code and Commentary, Volume 2 |
| ASTM E 2813 : 2012 | Standard Practice for Building Enclosure Commissioning |
| CSA Z320 : 2011 : INC : UPD 1 : 2011 | BUILDING COMMISSIONING |
| CSA Z320 : 2011 | BUILDING COMMISSIONING |
| ASTM E 2813 : 2012 : EDT 1 | Standard Practice for Building Enclosure Commissioning |
| ICC 2012 INTERNATIONAL RESI. CODE : 2012 | INTERNATIONAL RESIDENTIAL CODE FOR ONE- AND TWO-FAMILY DWELLINGS |
| ASTM E 3054/E3054M : 2016 | Standard Guide for Characterization and Use of Hygrothermal Models for Moisture Control Design in Building Envelopes |
| ASTM E 2634 : 2017-06 | SPECIFICATION FOR FLAT WALL INSULATING CONCRETE FORM (ICF) SYSTEMS |
| ASTM E 1105 : 2015 : REDLINE | Standard Test Method for Field Determination of Water Penetration of Installed Exterior Windows, Skylights, Doors, and Curtain Walls, by Uniform or Cyclic Static Air Pressure Difference |
| CSA Z8001 : 2013 | COMMISSIONING OF HEALTH CARE FACILITIES |
| ASCE/SEI 30 14 : 2014 | GUIDELINE FOR CONDITION ASSESSMENT OF THE BUILDING ENVELOPE |
| ASTM C 1401 : 2014 : REDLINE | Standard Guide for Structural Sealant Glazing |
| ASTM E 2099 : 2000 | Standard Practice for the Specification and Evaluation of Pre-Construction Laboratory Mockups of Exterior Wall Systems |
| ASTM E 2351 : 2004 : REV A : R2013 | Standard Guide for Specifying and Evaluating Performance of Single Family Attached and Detached Dwellings—Functionality (Withdrawn 2022) |
| ASTM E 2351 : 2004 | Standard Guide for Specifying and Evaluating Performance of Single Family Attached and Detached Dwellings-Functionality |
| ASTM E 2351 : 2004 : REV A | Standard Guide for Specifying and Evaluating Performance of Single Family Attached and Detached Dwellings-Functionality |
| ANSI/EIMA 99A : 2001 | EXTERIOR INSULATION AND FINISH SYSTEMS (EIFS) |
| ASTM E 1646 : 1995 : R2003 | Standard Test Method for Water Penetration of Exterior Metal Roof Panel Systems by Uniform Static Air Pressure Difference |
| ASTM C 964 : 2007 | Standard Guide for Lock-Strip Gasket Glazing |
| ASTM E 2128 : 2017 : REDLINE | Standard Guide for Evaluating Water Leakage of Building Walls |
| CSA A440 : 2017 | NORTH AMERICAN FENESTRATION STANDARD/SPECIFICATION FOR WINDOWS, DOORS, AND SKYLIGHTS |
| ASTM E 2112 : 2007 | Standard Practice for Installation of Exterior Windows, Doors and Skylights |
| ASTM E 1646 : 1995 : R2011 | Standard Test Method for Water Penetration of Exterior Metal Roof Panel Systems by Uniform Static Air Pressure Difference |
| ASTM E 2264 :2005 | Standard Practice for Determining the Effects of Temperature Cycling on Fenestration Products |
| ASTM D 7338 : 2014 : REDLINE | Standard Guide for Assessment Of Fungal Growth in Buildings |
| ASTM E 631 : 2015 : REDLINE | Standard Terminology of Building Constructions |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.