• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM E 502 : 2007

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods
Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Language(s)

English

Published date

15-01-2007

CONTAINED IN VOL. 14.02, 2015 Specifies the flash point of liquid and solid chemical compounds flashing from below -10 to 370 degrees C (16 to 700 degrees F).

1.1 This test method covers the determination of the flash point of liquid and solid chemical compounds flashing from below 10 to 370°C (16 to 700°F). The procedures and apparatus in Test Methods D 56, D 93, D 3278, D 3828, and D 3941 are to be used. Modification to these procedures are specified for tests on solids and viscous liquids. The significance of the results obtained is discussed along with possible sources of error and factors that might cause interference.

1.2 Suggestions for adapting this procedure to mixtures of chemicals are included (see Appendix X2).

1.3 This test method should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials or assemblies under actual fire conditions. However, results of this test method may be used as elements of a fire risk assessment that take into account all of the factors that are pertinent to an assessment of the fire hazard of a particular end use.

This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See also Section 8.

Committee
E 27
DocumentType
Test Method
Pages
6
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

NFPA 704 : 2017 STANDARD SYSTEM FOR THE IDENTIFICATION OF THE HAZARDS OF MATERIALS FOR EMERGENCY RESPONSE
NFPA 115 : 2016 LASER FIRE PROTECTION
ASTM D 8175 : 2018 Standard Test Method for Finite Flash Point Determination of Liquid Wastes by Pensky-Martens Closed Cup Tester
NFPA 30 : 2018 FLAMMABLE AND COMBUSTIBLE LIQUIDS CODE
NFPA 35 : 2016 MANUFACTURE OF ORGANIC COATINGS
NFPA FIRE PROT GUIDE ON HAZARDOUS MAT : 2010 FIRE PROTECTION GUIDE TO HAZARDOUS MATERIALS
SAE J 3042 : 2015 MEASURING PROPERTIES OF LI-BATTERY ELECTROLYTE
NFPA 1 : 2021 FIRE CODE
ASTM E 1232 : 2007 : R2013 Standard Test Method for Temperature Limit of Flammability of Chemicals
NFPA 321 : 1991 BASIC CLASSIFICATION OF FLAMMABLE AND COMBUSTIBLE LIQUIDS
NFPA 385 : 2017 TANK VEHICLES FOR FLAMMABLE AND COMBUSTIBLE LIQUIDS
AASHTO TP 102 : 2012 METHOD OF TEST FOR EVALUATION OF ASPHALT RELEASE AGENTS (ARAS)
NASA STD 6001(INT) : 2009 FLAMMABILITY, OFFGASSING, AND COMPATIBILITY REQUIREMENTS AND TEST PROCEDURES
NASA STD 6001 : 2011 FLAMMABILITY, OFFGASSING, AND COMPATIBILITY REQUIREMENTS AND TEST PROCEDURES
ASTM D 93 : 2016-07 TEST METHODS FOR FLASH POINT BY PENSKY-MARTENS CLOSED CUP TESTER
NFPA 68 : 2018 EXPLOSION PROTECTION BY DEFLAGRATION VENTING
ASTM E 1232 : 2007 Standard Test Method for Temperature Limit of Flammability of Chemicals
AASHTO TP 102 : 2012 : R2015 METHOD OF TEST FOR EVALUATION OF ASPHALT RELEASE AGENTS (ARAS)
ASTM D 8174 : 2018 Standard Test Method for Finite Flash Point Determination of Liquid Wastes by Small-Scale Closed Cup Tester
ASTM E 1232 : 2007 : R2019 Standard Test Method for Temperature Limit of Flammability of Chemicals
NFPA 1 : 2018 FIRE CODE

ASTM D 1310 : 2014 : REDLINE Standard Test Method for Flash Point and Fire Point of Liquids by Tag Open-Cup Apparatus
ASTM D 3941 : 2015-02 TEST METHOD FOR FLASH POINT BY THE EQUILIBRIUM METHOD WITH A CLOSED-CUP APPARATUS
ASTM D 93 : 2016-07 TEST METHODS FOR FLASH POINT BY PENSKY-MARTENS CLOSED CUP TESTER
ASTM E 1232 : 2007 Standard Test Method for Temperature Limit of Flammability of Chemicals

View more information
£62.61
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.