ASTM E 716 : 2016 : REDLINE
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry
Available format(s)
PDF
Superseded date
12-09-2022
Language(s)
English
Published date
01-06-2016
CONTAINED IN VOL. 03.05, 2016 Specifies procedures for producing a chill cast disk sample from molten aluminum during the production process, and from molten metal produced by melting pieces cut from products.
1.1These practices describe procedures for producing a chill cast disk sample from molten aluminum during the production process, and from molten metal produced by melting pieces cut from products.
1.2These practices describe a procedure for obtaining qualitative results by direct analysis of product using spark atomic emission spectrometry.
1.3These practices describe procedures for preparation of samples and products prior to analysis.
1.4The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.
1.5This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 6.1 and 7.2.
| Committee |
E 01
|
| DocumentType |
Redline
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
| SAE AMS 4280 : 2014 | ALUMINUM ALLOY CASTINGS, PERMANENT MOLD, 5.0SI - 1.2CU - 0.5MG (355.0-T71), SOLUTION HEAT TREATED AND OVERAGED |
| MIL-DTL-45225 Revision F:1998 | ALUMINUM ALLOY ARMOR, FORGED |
| ASTM B 236 : 2007 : R2015 | Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars) |
| ASTM B 234M : 2017 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Surface Condensers, Evaporators, and Heat Exchangers (Metric) |
| ASTM B 247M : 2015 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring Forgings (Metric) |
| MIL-DTL-46192 Revision C:1998 | ALUMINUM ALLOY ARMOR ROLLED PLATE (1/2 TO 4 INCHES THICK), WELDABLE (ALLOY 2519) |
| ASTM E 227 : 1990 : R1996 | Standard Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane Technique (Withdrawn 2002) |
| MIL-DTL-46063 Revision H:1998 | ARMOR PLATE, ALUMINUM ALLOY, 7039 |
| MIL A 46192 : B | ALUMINUM ALLOY ARMOR ROLLED PLATE (1/2 TO 4 INCHES THICK), WELDABLE (ALLOY 2519) |
| SAE AMS 4210 : 2012 | ALUMINUM ALLOY, CASTINGS - 5.0SI - 1.2CU - 0.50MG (355.0-T51) PRECIPITATION HEAT TREATED |
| MIL-DTL-32505 Revision A:2017 | ARMOR PLATE, ALUMINUM, ALLOYS 7017 AND 7020, WELDABLE |
| MIL-DTL-46083 Revision D:1998 | ALUMINUM ALLOY ARMOR, EXTRUDED, WELDABLE |
| ASTM B 736 : 2000 : R2006 | Standard Specification for Aluminum, Aluminum Alloy and Aluminum-Clad Steel Cable Shielding Stock (Withdrawn 2015) |
| SAE AMS 4223 : 2015 | ALUMINUM ALLOY, CASTINGS, 4.5CU - 0.70AG - 0.30MN - 0.25MG - 0.25TI (A201.0-T4), SOLUTION HEAT TREATED AND NATURALLY AGED |
| SAE AMS 4281 : 2014 | ALUMINUM ALLOY CASTINGS, PERMANENT MOLD, 5.0SI - 1.2CU - 0.50MG (355.0-T6), SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AMS 2355 : 2017 | QUALITY ASSURANCE, SAMPLING AND TESTING, ALUMINUM ALLOYS AND MAGNESIUM ALLOY, WROUGHT PRODUCTS (EXCEPT FORGING STOCK), AND ROLLED, FORGED, OR FLASH WELDED RINGS |
| ASTM E 2972 : 2015 | Standard Guide for Production, Testing, and Value Assignment of In-House Reference Materials for Metals, Ores, and Other Related Materials |
| ASTM B 317/B317M : 2007 : R2015 : EDT 1 | Standard Specification for Aluminum-Alloy Extruded Bar, Rod, Tube, Pipe, Structural Profiles, and Profiles for Electrical Purposes (Bus Conductor) |
| ASTM B 491/B491M : 2015 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Extruded Round Tubes for General-Purpose Applications |
| ASTM B 479 : 2006 | Standard Specification for Annealed Aluminum and Aluminum-Alloy Foil for Flexible Barrier, Food Contact, and Other Applications (Withdrawn 2015) |
| ASTM B 317/B317M : 2007 : R2015 | Standard Specification for Aluminum-Alloy Extruded Bar, Rod, Tube, Pipe, Structural Profiles, and Profiles for Electrical Purposes (Bus Conductor) |
| ASTM B 316/B316M : 2015 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and Rods |
| SAE AMS 4249B : 2012 (R2018) | ALUMINUM ALLOY CASTINGS 7.0SI - 0.58MG - 0.15TI - 0.06BE (D357.0-T6) SOLUTION AND PRECIPITATION HEAT TREATED (REQUIRING FATIGUE AND FRACTURE TOUGHNESS TESTING) |
| ASTM B 209 : 2014 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate |
| ASTM B 317/B317M : 2007 | Standard Specification for Aluminum-Alloy Extruded Bar, Rod, Tube, Pipe, Structural Profiles, and Profiles for Electrical Purposes (Bus Conductor) |
| ASTM E 826 : 2014 : REDLINE | Standard Practice for Testing Homogeneity of a Metal Lot or Batch in Solid Form by Spark Atomic Emission Spectrometry |
| SAE AMS 4235 : 2015 | ALUMINUM ALLOY CASTINGS, 4.6CU - 0.35MN - 0.25MG - 0.22TI (A206.0-T7), SOLUTION AND PRECIPITATION HEAT TREATED |
| ASTM B 736 : 2000 | Standard Specification for Aluminum, Aluminum Alloy and Aluminum-Clad Steel Cable Shielding Stock |
| SAE AMS 4290 : 2017 | ALUMINUM ALLOY, DIE CASTINGS 9.5SI - 0.50MG (360.0-F), AS CAST |
| ASTM B 985 : 2012 : R2016 | Standard Practice for Sampling Aluminum Ingots, Billets, Castings and Finished or Semi-Finished Wrought Aluminum Products for Compositional Analysis |
| ASTM E 101 : 1991 | Test Method for Spectrographic Analysis of Aluminum and Aluminum Alloys by the Point-To-Plane Technique (Withdrawn 1996) |
| ASTM B 928/B928M : 2015 : REDLINE | Standard Specification for High Magnesium Aluminum-Alloy Products for Marine Service and Similar Environments |
| SAE AMS 4291 : 2017 | ALUMINUM ALLOY, DIE CASTINGS, 8.5SI - 3.5CU (A380.0-F), AS CAST |
| SAE AMS 4406 : 2018 | Aluminum Alloy, Centrifugal Castings 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (709.0-T61) Hot Isostatically Pressed, Solution and Precipitation Heat Treated |
| SAE AMS 4482 : 2012 | CAST ALUMINUM ALLOY COMPOSITE 4.6 CU - 3.4TI - 1.4B - 0.75AG - 0.27MG (A205.0/TIB2/3P-T7P) SAND CAST, SOLUTION AND PRECIPITATION HEAT TREATED |
| ISO 6361-1:2011 | Wrought aluminium and aluminium alloys — Sheets, strips and plates — Part 1: Technical conditions for inspection and delivery |
| ASTM B 221 : 2014 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes |
| ASTM B 211M : 2012 : EDT 1 | Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold-Finished Bar, Rod, and Wire (Metric) (Withdrawn 2019) |
| ASTM B 985 : 2012 | Standard Practice for Sampling Aluminum Ingots, Billets, Castings and Finished or Semi-Finished Wrought Aluminum Products for Compositional Analysis |
| ASTM B 85 : 2003 | Standard Specification for Aluminum-Alloy Die Castings |
| ASTM E 3061 : 2017 | Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Inductively Coupled Plasma Atomic Emission Spectrometry (Performance Based Method) |
| ASTM B 236 : 2007 | Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars) |
| ASTM B 80 : 2015 : REDLINE | Standard Specification for Magnesium-Alloy Sand Castings |
| ASTM B 479 : 2019 | Standard Specification for Annealed Aluminum and Aluminum-Alloy Foil for Flexible Barrier, Food Contact, and Other Applications |
| ASTM B 211 : 2012 : EDT 1 | Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold Finished Bar, Rod, and Wire |
| ASTM B 236M : 2007 | Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars) [Metric] |
| SAE AMS 4214 : 2013 | CASTINGS, ALUMINUM ALLOY SAND, 5.0SI - 1.2CU - 0.50MG (355.0-T71), SOLUTION HEAT TREATED AND OVERAGED |
| SAE AMS 4285 : 2017 | ALUMINUM ALLOY CASTINGS, CENTRIFUGAL, 7.0SI - 0.30MG (356.0-T6), SOLUTION AND PRECIPITATION HEAT TREATED |
| ASTM B 928 : 2004 | Standard Specification for High Magnesium Aluminum-Alloy Sheet and Plate for Marine Service |
| SAE AMS 4212 : 2016 | Aluminum Alloy Castings 5.0Si - 1.2Cu - 0.50Mg (355.0-T6) Solution and Precipitation Heat Treated |
| SAE AMS 4225 : 2018 | ALUMINUM ALLOY, HEAT-RESISTANT, CASTINGS, 5.0CU - 1.5NI - 0.25MN - 0.25SB - 0.25CO - 0.20TI - 0.20ZR (203.0-T6), SOLUTION HEAT TREATED AND PRECIPITATION HEAT TREATED |
| SAE AMS 4229 : 2015 | ALUMINUM ALLOY CASTINGS, HIGH STRENGTH, 4.5CU - 0.70AG - 0.30MN - 0.25MG - 0.25TI (A201.0-T7), SOLUTION HEAT TREATED AND OVERAGED |
| ASTM B 483/B483M : 2013 : EDT 1 | Standard Specification for Aluminum and Aluminum-Alloy Drawn Tube and Drawn Pipe for General Purpose Applications |
| SAE AMS 4284 : 2017 | ALUMINUM ALLOY CASTINGS, PERMANENT MOLD, 7.0SI - 0.30MG (356.0-T6), SOLUTION AND PRECIPITATION HEAT TREATED |
| ASTM B 236M : 2007 : R2015 | Standard Specification for Aluminum Bars for Electrical Purposes (Bus Bars) (Metric) (Withdrawn 2024) |
| ASTM B 247 : 2015 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring Forgings |
| ASTM B 404/B404M : 2002 | Standard Specification for Aluminum and Aluminum-Alloy Seamless Condenser and Heat-Exchanger Tubes with Integral Fins (Withdrawn 2006) |
| SAE AMS 4219 : 2015 | ALUMINUM ALLOY CASTINGS, 7.0SI - 0.55MG - 0.12TI - 0.06BE (A357.0 T6), SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AMS 4286 : 2015 | ALUMINUM ALLOY CASTINGS, PERMANENT MOLD, 7.0SI - 0.32MG (356.0-T51), AS-CAST THEN PRECIPITATION HEAT TREATED |
| ASTM B 483/B483M : 2013 | Standard Specification for Aluminum and Aluminum-Alloy Drawn Pipe for General Purpose Applications |
| MIL-DTL-46027 Revision K:2007 | ARMOR PLATE, ALUMINUM ALLOY, WELDABLE 5083, 5456, & 5059 |
| 09/30196316 DC : 0 | BS ISO 6361-1 - WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS - SHEETS, STRIPS AND PLATES - PART 1: TECHNICAL CONDITIONS FOR INSPECTION AND DELIVERY |
| MIL-DTL-46118 Revision E:1998 | ALUMINUM ALLOY ARMOR, 2219, ROLLED PLATE AND DIE FORGED SHAPES |
| SAE AMS A 21180 : 2017 | ALUMINUM-ALLOY CASTINGS, HIGH STRENGTH |
| ASTM B 211 : 2012 | Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold Finished Bar, Rod, and Wire |
| ASTM E 607 : 2002 | Standard Test Method for Atomic Emission Spectrometric Analysis Aluminum Alloys by the Point to Plane Technique Nitrogen Atmosphere |
| SAE AMS 4288 : 2016 | ALUMINUM ALLOY CASTINGS, 7.0SI - 0.58MG - 0.15TI (E357.0-T6), SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AMS 4215 : 2013 | ALUMINUM ALLOY, CASTINGS, 5.0SI - 1.2CU - 0.50MG (C355.0-T6), SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AMS 4236 : 2015 | ALUMINUM ALLOY CASTINGS, 4.6CU - 0.35MN - 0.25MG - 0.22TI (A206.0-T4), SOLUTION HEAT TREATED AND NATURALLY AGED |
| ASTM B 241/B241M : 2016 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube |
| ASTM B 211M : 2012 | Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold-Finished Bar, Rod, and Wire (Metric) |
| ASTM B 313M : 1988 | Specification for Aluminum and Aluminum-Alloy Round Welded Tubes (Metric) (Withdrawn 1990) |
| ASTM E 1724 : 1995 : R2001 | Standard Guide for Testing and Certification of Metal and Metal-Related Reference Materials (Withdrawn 2010) |
| ISO 6362-1:2012 | Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and profiles — Part 1: Technical conditions for inspection and delivery |
| ASTM E 1724 : 1995 | Standard Guide for Testing and Certification of Metal and Metal-Related Reference Materials |
| MIL-DTL-32375 Revision B:2017 | Armor Plate, Aluminum Alloy, 7085, 7056, 7075, 7181, and 7099, Unweldable Applique |
| ASTM B 209M : 2014 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate (Metric) |
| MIL-DTL-32262 Revision A:2015 | ARMOR PLATE, ALUMINUM ALLOY 6055 WELDABLE & ALLOY 6061, UNWELDABLE APPLIQUE |
| SAE AMS 4261 : 2017 | ALUMINUM ALLOY CASTINGS, INVESTMENT, 7.0SI - 0.32MG (356.0-T51), PRECIPITATION HEAT TREATED |
| MIL-DTL-32341 Revision A:2015 | ARMOR PLATE, ALUMINUM, ALLOY 2139 WELDABLE & ALLOY 2195 AND 2060 UNWELDABLE APPLIQUE |
| ASTM B 234 : 2017 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Surface Condensers, Evaporators, and Heat Exchangers |
| SAE AMS 4217 : 2018 | ALUMINUM ALLOY, CASTINGS, 7.0SI - 0.32MG (356.0-T6), SOLUTION AND PRECIPITATION HEAT TREATED |
| ISO 6363-1:2012 | Wrought aluminium and aluminium alloys — Cold-drawn rods/bars, tubes and wires — Part 1: Technical conditions for inspection and delivery |
| SAE AMS 4471 : 2014 | CAST ALUMINUM ALLOY COMPOSITE 4.6CU - 3.4TI - 1.4B - 0.75AG - 0.27MG (205.0/TIB[2]/3P-T7P) INVESTMENT CAST, SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AMS 4242 : 2015 | ALUMINUM ALLOY, CASTINGS, 4.7CU - 0.60AG - 0.35MN - 0.25MG - 0.25TI (B201.0-T7), SOLUTION HEAT TREATED AND OVERAGED |
| SAE AMS 4241 : 2015 | ALUMINUM ALLOY CASTINGS, 7.0SI - 0.58MG - 0.15TI - 0.06BE (D357.0-T6), SOLUTION AND PRECIPITATION HEAT TREATED, DENDRITE ARM SPACING (DAS) CONTROLLED |
| ASTM B 308M : 1988 | Specification for Aluminum-Alloy 6061-T6 Standard Structural Shapes, Rolled or Extruded (Metric) (Withdrawn 1990) |
| ASTM E 607 : 2002 | Standard Test Method for Atomic Emission Spectrometric Analysis Aluminum Alloys by the Point to Plane Technique Nitrogen Atmosphere |
| ASTM E 401 : 79(1989)E1 | RECOMMENDED PRACTICE FOR BONDING THIN SPECTROCHEMICAL SAMPLES AND STANDARDS TO A GREATER MASS OF MATERIAL |
£62.61
Excluding VAT
GBP
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.