• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM E 96/E96M : 2021

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials
Available format(s)

Hardcopy , PDF

Superseded date

03-12-2022

Language(s)

English

Published date

15-12-2021

1.1These test methods cover the determination of water vapor transmission rate (WVTR) of materials, such as, but not limited to, paper, plastic films, other sheet materials, coatings, foams, fiberboards, gypsum and plaster products, wood products, and plastics. Two basic methods, the Desiccant Method and the Water Method, are provided for the measurement of WVTR. In these tests, the desired temperature and side-to-side humidity conditions, with resultant vapor drive through the specimen, are used. Agreement is not to be expected between results obtained by different methods. The test conditions employed are at the discretion of the user, but in all cases, are reported with the results.

1.2The values stated in either Inch-Pound or SI units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, each system shall be used independently of the other. Derived results are converted from one system to the other using appropriate conversion factors (see Table 1).

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
C 16
DocumentType
Test Method
Pages
15
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM C 171 : 2020 Standard Specification for Sheet Materials for Curing Concrete
ASTM D 8065/D8065M : 2016 Standard Classification System and Basis for Specification for Specifying Plastic Films
ASTM C 755 : 2020 Standard Practice for Selection of Water Vapor Retarders for Thermal Insulation
ASTM C 928/C928M : 2020 : REV A Standard Specification for Packaged, Dry, Rapid-Hardening Cementitious Materials for Concrete Repairs
ASTM C 552 : 2021 : REV A Standard Specification for Cellular Glass Thermal Insulation
ASTM F 2407 : 2020 Standard Specification for Surgical Gowns Intended for Use in Healthcare Facilities
ASTM E 2556/E2556M : 2010 : R2016 Standard Specification for Vapor Permeable Flexible Sheet Water-Resistive Barriers Intended for Mechanical Attachment
ASTM C 1258 : 2021 : REV A Standard Test Method for Elevated Temperature and Humidity Resistance of Vapor Retarders for Insulation
ASTM E 398 : 2020 Standard Test Method for Water Vapor Transmission Rate of Sheet Materials Using Dynamic Relative Humidity Measurement
ASTM C 727 : 2019 Standard Practice for Installation and Use of Reflective Insulation in Building Constructions
ASTM C 1594 : 2011 : R2017 Standard Specification for Polyimide Rigid Cellular Thermal Insulation
ASTM D 7709 : 2012 : R2017 Standard Test Methods for Measuring Water Vapor Transmission Rate (WVTR) of Pharmaceutical Bottles and Blisters
ASTM E 1549/E1549M : 2013 : R2016 Standard Specification for ESD Controlled Garments Required in Cleanrooms and Controlled Environments for Spacecraft for Non-Hazardous and Hazardous Operations
ASTM D 3833/D3833M : 1996 : R2019 Standard Test Method for Water Vapor Transmission of Pressure-Sensitive Tapes
ASTM D 2626/D2626M : 2004 : R2020 Standard Specification for Asphalt-Saturated and Coated Organic Felt Base Sheet Used in Roofing
ASTM D 6380/D6380M : 2003 : R2018 Standard Specification for Asphalt Roll Roofing (Organic Felt)
ASTM D 5456 : 2021 : EDT 1 Standard Specification for Evaluation of Structural Composite Lumber Products
ASTM C 1482 : 2017 Standard Specification for Polyimide Flexible Cellular Thermal and Sound Absorbing Insulation
ASTM D 3664 : 2016 Standard Specification for Biaxially Oriented Polymeric Resin Film for Capacitors in Electrical Equipment (Withdrawn 2022)
ASTM D 6694/D6694M : 2015 Standard Specification for Liquid-Applied Silicone Coating Used in Spray Polyurethane Foam Roofing Systems
ASTM E 2570/E2570M : 2007 : R2019 Standard Test Methods for Evaluating Water-Resistive Barrier (WRB) Coatings Used under Exterior Insulation and Finish Systems (EIFS) or EIFS with Drainage
ASTM C 1396/C1396M : 2017 Standard Specification for Gypsum Board
ASTM C 1126 : 2019 Standard Specification for Faced or Unfaced Rigid Cellular Phenolic Thermal Insulation
ASTM C 1902 : 2020 Standard Specification for Cellular Glass Insulation Used in Building and Roof Applications
ASTM F 2902 : 2016 : EDT 1 Standard Guide for Assessment of Absorbable Polymeric Implants
ASTM C 578 : 2019 Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation
ASTM C 1483/C1483M : 2017 Standard Specification for Exterior Solar Radiation Control Coatings on Buildings
ASTM C 209 : 2020 Standard Test Methods for Cellulosic Fiber Insulating Board
ASTM C 1668 : 2020 Standard Specification for Externally Applied Reflective Insulation Systems on Rigid Duct in Heating, Ventilation, and Air Conditioning (HVAC) Systems
ASTM D 7425/D7425M : 2013 : R2019 Standard Specification for Spray Polyurethane Foam Used for Roofing Applications
ASTM D 4068 : 2017 Standard Specification for Chlorinated Polyethylene (CPE) Sheeting for Concealed Water-Containment Membrane
ASTM D 4708 : 2019 Standard Practice for Preparation of Uniform Free Films of Organic Coatings
ASTM F 2733 : 2021 Standard Specification for Flame-Resistant Rainwear for Protection Against Flame Hazards
ASTM C 887 : 2020 Standard Specification for Packaged, Dry, Combined Materials for Surface Bonding Mortar
ASTM C 1029 : 2020 Standard Specification for Spray-Applied Rigid Cellular Polyurethane Thermal Insulation
ASTM C 1224 : 2015 : R2020 Standard Specification for Reflective Insulation for Building Applications
ASTM D 6523 : 2000 : R2014 : EDT 1 Standard Guide for Evaluation and Selection of Alternative Daily Covers (ADCs) for Sanitary Landfills
ASTM D 6826 : 2005 : R2014 : EDT 1 Standard Specification for Sprayed Slurries, Foams and Indigenous Materials Used As Alternative Daily Cover for Municipal Solid Waste Landfills
ASTM F 602 : 2009 : R2015 Standard Criteria for Implantable Thermoset Epoxy Plastics
ASTM D 4000 : 2020 Standard Classification System for Specifying Plastic Materials
ASTM D 3105 : 2017 Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials
ASTM C 1696 : 2020 Standard Guide for Industrial Thermal Insulation Systems
ASTM C 1713 : 2017 Standard Specification for Mortars for the Repair of Historic Masonry
ASTM C 534/C534M : 2020 : REV A Standard Specification for Preformed Flexible Elastomeric Cellular Thermal Insulation in Sheet and Tubular Form
ASTM D 4819 : 2013 : R2021 : EDT 1 Standard Specification for Flexible Cellular Materials Made From Polyolefin Plastics
ASTM D 6153 : 2015 Standard Specification for Materials for Bridge Deck Waterproofing Membrane Systems
ASTM E 154/E154M : 2008 : REV A : R2019 Standard Test Methods for Water Vapor Retarders Used in Contact with Earth Under Concrete Slabs, on Walls, or as Ground Cover
ASTM D 2643/D2643M : 2021 Standard Specification for Prefabricated Bituminous Geomembrane Used as Canal and Ditch Liner (Exposed Type)
ASTM C 1289 : 2021 Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board
ASTM C 551/C551M : 2007 : R2019 Standard Specification for Asbestos-Cement Fiberboard Insulating Panels (Withdrawn 2022)
ASTM F 624 : 2009 : R2015 : EDT 1 Standard Guide for Evaluation of Thermoplastic Polyurethane Solids and Solutions for Biomedical Applications
ASTM E1677 : 2019 Standard Specification for Air Barrier (AB) Material or Assemblies for Low-Rise Framed Building Walls<br>
ASTM F 3510 : 2021 Standard Guide for Characterizing Fiber-Based Constructs for Tissue-Engineered Medical Products
ASTM G 21 : 2015 : R2021 : EDT 1 Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi
ASTM D 7106/D7106M : 2005 : R2015 : EDT 1 Standard Guide for Selection of Test Methods for Ethylene Propylene Diene Terpolymer (EPDM) Geomembranes
ASTM B 479 : 2019 Standard Specification for Annealed Aluminum and Aluminum-Alloy Foil for Flexible Barrier, Food Contact, and Other Applications
ASTM C 1692 : 2018 Standard Practice for Construction and Testing of Autoclaved Aerated Concrete (AAC) Masonry
ASTM E 1993/E1993M : 1998 : R2020 Standard Specification for Bituminous Water Vapor Retarders Used in Contact with Soil or Granular Fill Under Concrete Slabs
ASTM C 591 : 2021 Standard Specification for Unfaced Preformed Rigid Cellular Polyisocyanurate Thermal Insulation
ASTM C 1278/C1278M : 2017 Standard Specification for Fiber-Reinforced Gypsum Panel
ASTM C 11 : 2018 : REV B Standard Terminology Relating to Gypsum and Related Building Materials and Systems
ASTM D 6434 : 2012 : R2018 Standard Guide for the Selection of Test Methods for Flexible Polypropylene Geomembranes
ASTM C 665 : 2017 Standard Specification for Mineral-Fiber Blanket Thermal Insulation for Light Frame Construction and Manufactured Housing
ASTM D 2673 : 2014 Standard Specification for Oriented Polypropylene Film
ASTM F 3299 : 2018 Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using an Electrolytic Detection Sensor (Coulometric P<inf>2</inf>O<inf >5</inf> Sensor)
ASTM E 1745 : 2017 Standard Specification for Plastic Water Vapor Retarders Used in Contact with Soil or Granular Fill under Concrete Slabs
ASTM D 8257/D8257M : 2020 Standard Specification for Mechanically Attached Polymeric Roof Underlayment Used in Steep Slope Roofing
ASTM D 7008 : 2008 : R2018 Standard Specification for Geosynthetic Alternate Daily Covers
ASTM D 4397 : 2016 Standard Specification for Polyethylene Sheeting for Construction, Industrial, and Agricultural Applications
ASTM D 6630/D6630M : 2016 Standard Guide for Low Slope Insulated Roof Membrane Assembly Performance
ASTM E 2321 : 2003 : R2019 Standard Practice for Use of Test Methods <astmref rid="a00002"/> for Determining the Water Vapor Transmission (WVT) of Exterior Insulation and Finish Systems (EIFS)
ASTM C 1423 : 2021 Standard Guide for Selecting Jacketing Materials for Thermal Insulation
ASTM D 1970/D1970M : 2021 Standard Specification for Self-Adhering Polymer Modified Bituminous Sheet Materials Used as Steep Roofing Underlayment for Ice Dam Protection
ASTM C 1136 : 2021 Standard Specification for Flexible, Low Permeance Vapor Retarders for Thermal Insulation
ASTM C 1290 : 2016 : R2021 Standard Specification for Flexible Fibrous Glass Blanket Insulation Used to Externally Insulate HVAC Ducts
ASTM C 1321 : 2015 : R2020 Standard Practice for Installation and Use of Interior Radiation Control Coating Systems (IRCCS) in Building Construction
ASTM D 7230 : 2006 : R2021 Standard Guide for Evaluating Polymeric Lining Systems for Water Immersion in Coating Service Level III Safety-Related Applications on Metal Substrates
ASTM E 631 : 2015 Standard Terminology of Building Constructions
ASTM C 1313/C1313M : 2013 : R2019 Standard Specification for Sheet Radiant Barriers for Building Construction Applications
ASTM D 6455 : 2011 : R2018 Standard Guide for the Selection of Test Methods for Prefabricated Bituminous Geomembranes (PBGMs)
ASTM D 4551 : 2017 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Flexible Concealed Water-Containment Membrane
ASTM C 647 : 2019 Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation
ASTM D 4635 : 2016 Standard Specification for Plastic Films Made from Low-Density Polyethylene and Linear Low-Density Polyethylene for General Use and Packaging Applications
ASTM D 4649 : 2020 Standard Guide for Use of Stretch Films and Wrapping Application
ASTM D 5886 : 1995 : R2018 Standard Guide for Selection of Test Methods to Determine Rate of Fluid Permeation Through Geomembranes for Specific Applications
ASTM F 1249 : 2020 Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor
ASTM D 2103 : 2015 Standard Specification for Polyethylene Film and Sheeting
ASTM D 7407 : 2007 : R2020 Standard Guide for Determining the Transmission of Gases Through Geomembranes
ASTM D 3468/D3468M : 1999 : R2020 Standard Specification for Liquid-Applied Neoprene and Chlorosulfonated Polyethylene Used in Roofing and Waterproofing
ASTM C 1427 : 2021 Standard Specification for Extruded Preformed Flexible Cellular Polyolefin Thermal Insulation in Sheet and Tubular Form
ASTM E 3069 : 2019 : REV A Standard Guide for Evaluation and Rehabilitation of Mass Masonry Walls for Changes to Thermal and Moisture Properties of the Wall
ASTM D 5047 : 2017 Standard Specification for Polyethylene Terephthalate Film and Sheeting
AWWA C217:2023 Microcrystalline Wax and Petrolatum Tape Coating Systems for Steel Water Pipe and Fittings
ASTM C 1809 : 2020 Standard Practice for Preparation of Specimens and Reporting of Results for Permeance Testing of Pressure Sensitive Adhesive Sealed Joints in Insulation Vapor Retarders
ASTM D 8257/D8257M : 2022 Standard Specification for Mechanically Attached Polymeric Roof Underlayment Used in Steep Slope Roofing
ASTM C 552 : 2022 Standard Specification for Cellular Glass Thermal Insulation
ASTM C 1289 : 2022 Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board

View more information
£69.29
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.