• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM F 1173 : 2001 : R2018

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Thermosetting Resin Fiberglass Pipe Systems to Be Used for Marine Applications
Available format(s)

Hardcopy , PDF

Superseded date

09-06-2023

Language(s)

English

Published date

04-04-2018

CONTAINED IN VOL. 01.07, 2018 Defines reinforced thermosetting resin pipe systems with nominal pipe sizes (NPS) 1 through 48 in. (25 through 1200 mm) which are to be used for all fluids approved by the authority having jurisdiction in marine piping systems.

1.1This specification covers reinforced thermosetting resin pipe systems with nominal pipe sizes (NPS) 1 through 48 in. (25 through 1200 mm) which are to be used for all fluids approved by the authority having jurisdiction in marine piping systems.

1.2The dimensionless designator NPS has been substituted for traditional terms as “nominal diameter,” “size,” and “nominal size.”

1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4The following safety hazards caveat pertains to the test methods which are included in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
F 25
DocumentType
Standard
Pages
15
ProductNote
Reconfirmed 2018
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 5677 : 2017 Standard Specification for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Pipe Fittings, Adhesive Bonded Joint Type, for Aviation Jet Turbine Fuel Lines

ASTM D 2105 : 1997 Standard Test Method for Longitudinal Tensile Properties of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Tube
ASTM D 2310 : 2001 Standard Classification for Machine-Made "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
ASTM D 2924 : 2012 : R2017 Standard Test Method for External Pressure Resistance of “Fiberglass”<brk /> (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
CFR 46(PTS41-69) : OCT 2017 SHIPPING - COAST GUARD, DEPARTMENT OF TRANSPORTATION
ASTM D 1598 : 2002 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
NSF 61 : 2016 DRINKING WATER SYSTEM COMPONENTS - HEALTH EFFECTS
ASTM D 1598 : 2015 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM D 2584 : 2002 Standard Test Method for Ignition Loss of Cured Reinforced Resins
ASTM F 412 : 2020 : REV A Standard Terminology Relating to Plastic Piping Systems
ASTM D 1598 : 2015 : REV A Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM F 412 : 2021 Standard Terminology Relating to Plastic Piping Systems
ASTM D 2992 : 2022 Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings
ASTM D 5686 : 1995 Standard Specification for "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Pipe Fittings, Adhesive Bonded Joint Type Epoxy Resin, for Condensate Return Lines (Withdrawn 2002)
ASTM D 5028 : 1996 Standard Test Method for Curing Properties of Pultrusion Resins by Thermal Analysis
ASTM D 3859 : 2015 : REDLINE Standard Test Methods for Selenium in Water
ASTM D 2310 : 2006 : R2012 Standard Classification for Machine-Made “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe (Withdrawn 2017)
CFR 21(PTS170-199) : 0 FOOD AND DRUGS - FOOD AND DRUG ADMINISTRATION, CHAPTER 1 DEPARTMENT OF HEALTH AND HUMAN SERVICES - PARTS 170-199
ASTM E 1529 : 2000 Standard Test Methods for Determining Effects of Large Hydrocarbon Pool Fires on Structural Members and Assemblies
ASTM D 2992 : 2001 Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings
ASTM D 2584 : 2008 Standard Test Method for Ignition Loss of Cured Reinforced Resins
ASTM E 1529 : 2016 : EDT 1 Standard Test Methods for Determining Effects of Large Hydrocarbon Pool Fires on Structural Members and Assemblies
ISO 75:1987 Plastics and ebonite Determination of temperature of deflection under load
ASTM D 2310 : 2006 Standard Classification for Machine-Made "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
ASTM D 2584 : 1994 Standard Test Method for Ignition Loss of Cured Reinforced Resins
ASTM E 1529 : 2010 Standard Test Methods for Determining Effects of Large Hydrocarbon Pool Fires on Structural Members and Assemblies
ASTM D 883 : 2022 Standard Terminology Relating to Plastics
ASTM D 3567 : 1997 : R2006 Standard Practice for Determining Dimensions of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
ASTM D 883 : 2020 : REV B Standard Terminology Relating to Plastics
ASTM D 2924 : 2001 Standard Test Method for External Pressure Resistance of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
ASTM E 1529 : 2014 : REV A Standard Test Methods for Determining Effects of Large Hydrocarbon Pool Fires on Structural Members and Assemblies
ASTM E 1529 : 2013 Standard Test Methods for Determining Effects of Large Hydrocarbon Pool Fires on Structural Members and Assemblies
ASTM D 3567 : 2017 : R2022 Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
ASTM D 2584 : 2011 Standard Test Method for Ignition Loss of Cured Reinforced Resins
ASTM D 1598 : 1997 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM D 2105 : 2001 Standard Test Method for Longitudinal Tensile Properties of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Tube
ASTM D 1599 : 2014 Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
ASTM E 1529 : 2006 Standard Test Methods for Determining Effects of Large Hydrocarbon Pool Fires on Structural Members and Assemblies
ASTM D 1599 : 2014 : EDT 1 Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
ASTM E 1529 : 2016 Standard Test Methods for Determining Effects of Large Hydrocarbon Pool Fires on Structural Members and Assemblies
ASTM D 3567 : 1997 : R2002 Standard Practice for Determining Dimensions of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
ASTM D 1599 : 2018 Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
ASTM D 2105 : 2001 : R2014 Standard Test Method for Longitudinal Tensile Properties of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Tube
ASTM D 1599 : 1999 : R2011 Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
ASTM D 1599 : 1999 : EDT 1 Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings
ASTM D 5028 : 2017 Standard Test Method for Curing Properties of Pultrusion Resins by Thermal Analysis
ASTM D 2584 : 1968 Standard Method Of Test For Ignition Loss Of Cured Reinforced Resins
ASTM D 2992 : 2006 Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings
ASTM D 1598 : 2021 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ISO 9001:2015 Quality management systems — Requirements
ASTM D 1598 : 2002 : R2008 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASME B16.5 : 2017 PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD
ASTM D 2924 : 2012 Standard Test Method for External Pressure Resistance of “Fiberglass”<brk /> (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
ASTM D 3567 : 1997 Standard Practice for Determining Dimensions of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
ASTM D 2924 : 2001 : R2006 Standard Test Method for External Pressure Resistance of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
ASTM D 2924 : 1999 Standard Test Method for External Pressure Resistance of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
ASTM E 1529 : 2014 Standard Test Methods for Determining Effects of Large Hydrocarbon Pool Fires on Structural Members and Assemblies
ASTM D 2584 : 2018 Standard Test Method for Ignition Loss of Cured Reinforced Resins
ASTM D 2992 : 1996 : EDT 1 Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings
ASTM D 2105 : 2001 : R2019 Standard Test Method for Longitudinal Tensile Properties of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Tube
ASTM D 1599 : 1999 : R2005 Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
ASTM D 1598 : 2002 : R2009 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM D 5028 : 2017 : REDLINE Standard Test Method for Curing Properties of Pultrusion Resins by Thermal Analysis
ASTM D 3567 : 2017 Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
ASTM D 5028 : 2009 Standard Test Method for Curing Properties of Pultrusion Resins by Thermal Analysis
ASTM E 1529 : 2022 Standard Test Methods for Determining Effects of Large Hydrocarbon Pool Fires on Structural Members and Assemblies
ASTM D 2992 : 2012 Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings
ASTM D 2310 : 1997 Standard Classification for Machine-Made "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
ASTM D 2992 : 2018 Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings
ASTM D 1599 : 1999 Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings
ASTM D 3567 : 1997 : R2011 Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
ASTM D 2105 : 2001 : R2007 : EDT 1 Standard Test Method for Longitudinal Tensile Properties of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Tube

View more information
£69.29
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.