ASTM F 1588 : 1996 : R2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
12-11-2019
English
01-08-2015
CONTAINED IN VOL. 08.04, 2017 Specifies to demonstrate that a joint in a plastic piping system is resistant to the effects of long-term creep.
1.1The constant tensile load joint test (CTLJT) is designed to demonstrate that a joint in a plastic piping system is resistant to the effects of long-term creep.
1.1.1The joint is subjected to an internal pressure at least equal to its operating pressure and a sustained axial tensile load for a specified time period, usually 1000 h. The joint shall not leak, nor may the pipe completely pull out for the test duration. The total axial stress is set by the referencing document.
1.1.2Some typical conditions for testing of joints on polyethylene pipe are described in Appendix X1.
1.2This test is usually performed at 73°F (22.8°C).
1.3The CTLJT was developed to demonstrate the long-term resistance to pullout of mechanical joints on polyethylene gas pipe. The CTLJT has also been successfully applied to the evaluation of other components of plastic piping systems. These applications are discussed in Appendix X1.
1.4The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| Committee |
F 17
|
| DocumentType |
Test Method
|
| Pages |
4
|
| ProductNote |
Reconfirmed 2015
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM F 2145 : 2013 : R2018 | Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing |
| ASTM F 1924 : 2019 | Standard Specification for Plastic Mechanical Fittings for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing |
| ASTM F 1924 : 2012 | Standard Specification for Plastic Mechanical Fittings for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing |
| ASTM F 1973 : 2013 : R2018 | Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems |
| ASTM F 1948 : 2015 | Standard Specification for Metallic Mechanical Fittings for Use on Outside Diameter Controlled Thermoplastic Gas Distribution Pipe and Tubing |
| ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 2513 : 2006 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2122 : 1998 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2513 : 2016 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2003 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2012 : REV A | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2008 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2011 : REV B | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2006 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2009 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2004 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 1987 | Standard Specification for Thermoplastic Gas Pressure Piping Systems |
| ASTM D 2513 : 2011 : REV C | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASME B31.8 : 2016 | Gas Transmission and Distribution Piping Systems |
| ASTM D 2513 : 2016 : REV A | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2013 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 1999 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2009 : REV A | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1600 : 2007 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 2513 : 2003 : REV B | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1600 : 2013 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 2513 : 2001 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2001 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1600 : 2014 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| CFR 49(PTS186-199) : 0 | TRANSPORTATION |
| ASTM D 2513 : 2001 : REV A : EDT 1 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1600 : 2008 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 2513 : 2011 : EDT 1 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2014 : EDT 1 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2014 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2000 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2007 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2019 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2011 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2122 : 1998 : EDT 1 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2513 : 2008 : REV B | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2017-01 | SPECIFICATION FOR POLYETHYLENE (PE) GAS PRESSURE PIPE, TUBING, AND FITTINGS |
| ASTM D 2513 : 2003 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2006 : REV B | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
| ASTM D 2122 : 2016 : REDLINE | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2513 : 2007 : REV B : EDT 1 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2008 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2018 : REV A | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2122 : 1998 : R2004 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2122 : 2016 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2513 : 2007 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2007 : REV B | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2012 : REV A : EDT 1 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2122 : 1998 : R2010 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2513 : 2018 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2011 : REV A | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2012 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
| ASTM D 2513 : 2004 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2122 : 2015 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2513 : 2005 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.