ASTM F 1924 : 2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Specification for Plastic Mechanical Fittings for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing
Hardcopy , PDF
27-08-2020
English
01-04-2012
1.1 This specification describes requirements and test methods for the qualification of plastic bodied mechanical fittings for use with outside diameter controlled polyethylene (PE) gas distribution pipe, nominal 2 pipe size (IPS) and smaller complying with Specification D2513. In addition, it specifies general requirements of the material from which these fittings are made.
1.2 The test methods described in this specification are not intended to be used as routine quality control tests.
1.3 This specification covers the types of mechanical fittings described in 3.2.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5 The following safety hazards caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.6 The text of this specification references notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification.
| Committee |
F 17
|
| DocumentType |
Standard
|
| Pages |
5
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM F 412 : 2019 | Standard Terminology Relating to Plastic Piping Systems |
| ASTM D 2837 : 2013 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
| ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM F 2897 : 2011 | Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances) |
| ASTM D 1598 : 2002 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 2513 : 2006 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM F 1588 : 1996 | Standard Test Method for Constant Tensile Load Joint Test (CTLJT) |
| ASTM D 2513 : 2016 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1598 : 2015 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 1598 : 2015 : REV A | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 2513 : 2003 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2012 : REV A | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2837 : 2001 : REV A | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials |
| ASTM D 2513 : 2008 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2011 : REV B | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM F 2897 : 2014 | Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances) |
| ASTM D 2513 : 2006 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2009 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2004 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 1987 | Standard Specification for Thermoplastic Gas Pressure Piping Systems |
| ASTM D 2513 : 2011 : REV C | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM F 2897 : 2011 : REV A : EDT 1 | Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances) |
| ASTM D 2837 : 2002 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials |
| ASTM D 2837 : 2001 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials |
| ASTM D 2513 : 2016 : REV A | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2837 : 2004 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
| ASTM D 2513 : 2013 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 1999 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2009 : REV A | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1600 : 2007 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 2513 : 2003 : REV B | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1600 : 2013 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 2513 : 2001 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2001 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1600 : 2014 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 2837 : 2008 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
| ASTM D 2837 : 1998 : REV A | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials |
| ASTM D 2513 : 2001 : REV A : EDT 1 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1600 : 2008 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1598 : 1997 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 2513 : 2011 : EDT 1 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2014 : EDT 1 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2837 : 2001 : REV A : EDT 1 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials |
| ASTM D 2837 : 2011 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
| ASTM D 2513 : 2014 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2000 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2007 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM F 2897 : 2015 : REV A | Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances) |
| ASTM D 2513 : 2011 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2008 : REV B | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2003 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2006 : REV B | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
| ASTM F 2897 : 2015 | Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances) |
| ASTM D 2513 : 2007 : REV B : EDT 1 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2008 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1598 : 2002 : R2008 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM F 1588 : 1996 : R2002 | Standard Test Method for Constant Tensile Load Joint Test (CTLJT) |
| ASTM F 1588 : 1996 : R2011 | Standard Test Method for Constant Tensile Load Joint Test (CTLJT) |
| ASTM D 1598 : 2002 : R2009 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM F 1588 : 1996 : R2007 | Standard Test Method for Constant Tensile Load Joint Test (CTLJT) |
| ASTM D 2513 : 2007 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM F 1588 : 1996 : R2015 | Standard Test Method for Constant Tensile Load Joint Test (CTLJT) |
| ASTM D 2513 : 2007 : REV B | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2012 : REV A : EDT 1 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM F 2897 : 2011 : REV A | Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances) |
| ASTM D 2513 : 2018 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2011 : REV A | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2012 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2004 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2005 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2837 : 2013 : EDT 1 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
| ASTM D 2837 : 2004 : EDT 1 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.