• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM F 2418 : 2019

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Polypropylene (PP) Corrugated Wall Stormwater Collection Chambers
Available format(s)

Hardcopy , PDF

Superseded date

19-10-2023

Language(s)

English

Published date

02-09-2019

1.1This specification covers requirements, test methods, materials, and marking for polypropylene (PP), open bottom, buried chambers of corrugated wall construction used for collection, detention, and retention of stormwater runoff. Applications include commercial, residential, agricultural, and highway drainage, including installation under parking lots and roadways.

1.2Chambers are produced in arch shapes with dimensions based on chamber rise, chamber span, and wall stiffness. Chambers are manufactured with integral feet that provide base support. Chambers may include perforations to enhance water flow. Chambers must meet test requirements for arch stiffness, flattening, and accelerated weathering.

1.3Analysis and experience have shown that the successful performance of this product depends upon the type and depth of bedding and backfill, and care in installation. This specification includes requirements for the manufacturer to provide chamber installation instructions to the purchaser.

1.4The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.5This standard does not purport to address water quality issues or hydraulic performance requirements associated with its use. It is the responsibility of the user to ensure that appropriate engineering analysis is performed to evaluate the water quality issues and hydraulic performance requirements for each installation.

1.6The following safety hazards caveat pertains only to the test method portion, Section 6, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
F 17
DocumentType
Standard
Pages
7
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM F 2787 : 2013 : R2018 Standard Practice for Structural Design of Thermoplastic Corrugated Wall Stormwater Collection Chambers

ASTM D 256 : 2010 : R2018 Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
ASTM D 4329 : 2021 Standard Practice for Fluorescent Ultraviolet (UV) Lamp Apparatus Exposure of Plastics
ASTM F 412 : 2020 : REV A Standard Terminology Relating to Plastic Piping Systems
ASTM F 412 : 2021 Standard Terminology Relating to Plastic Piping Systems
ASTM D 256 : 2023 : EDT 1 Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
ASTM D 4329 : 2013 Standard Practice for Fluorescent Ultraviolet (UV) Lamp Apparatus Exposure of Plastics
ASTM D 256 : 2023 Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
ASTM D 6992 : 2016 : R2023 Standard Test Method for Accelerated Tensile Creep and Creep-Rupture of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method
ASTM D 6992 : 2016 Standard Test Method for Accelerated Tensile Creep and Creep-Rupture of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method
ASTM D 638 : 2014 Standard Test Method for Tensile Properties of Plastics
ASTM D 2412 : 2021 Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
ASTM D 2122 : 2022 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 618 : 2013 Standard Practice for Conditioning Plastics for Testing
ASTM F 412 : 2023 Standard Terminology Relating to Plastic Piping Systems
ASTM D 2122 : 2016 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 2412 : 2011 : R2018 Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
ASTM D 618 : 2021 Standard Practice for Conditioning Plastics for Testing
ASTM D 638 : 2022 Standard Test Method for Tensile Properties of Plastics

View more information
£62.61
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.