• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM F 2617 : 2015

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Identification and Quantification of Chromium, Bromine, Cadmium, Mercury, and Lead in Polymeric Material Using Energy Dispersive X-ray Spectrometry
Available format(s)

Hardcopy , PDF

Superseded date

09-11-2023

Language(s)

English

Published date

14-10-2015

This test method describes an energy dispersive X-ray fluorescence (EDXRF) spectrometric procedure for identification and quantification of chromium, bromine, cadmium, mercury, and lead in polymeric materials.

1.1This test method describes an energy dispersive X-ray fluorescence (EDXRF) spectrometric procedure for identification and quantification of chromium, bromine, cadmium, mercury, and lead in polymeric materials.

1.2This test method is not applicable to determine total concentrations of polybrominated biphenyls (PBB), polybrominated diphenyl ethers (PBDE) or hexavalent chromium. This test method cannot be used to determine the valence states of atoms or ions.

1.3This test method is applicable for a range from 20 mg/kg to approximately 1 wt % for chromium, bromine, cadmium, mercury, and lead in polymeric materials.

1.4This test method is applicable for homogeneous polymeric material.

1.5The values stated in SI units are to be regarded as the standard. Values given in parentheses are for information only.

1.6This test method is not applicable to quantitative determinations for specimens with one or more surface coatings present on the analyzed surface; however, qualitative information may be obtained. In addition, specimens less than infinitely thick for the measured X rays, must not be coated on the reverse side or mounted on a substrate.

1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
F 40
DocumentType
Test Method
Pages
12
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 4703 : 2002 Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
ASTM D 6299 : 2010 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 6299 : 2013 : EDT 1 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM E 177 : 1990 : REV A : R1996 Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods
ASTM F 2576 : 2006 : REV A Standard Terminology Relating to Declarable Substances in Materials
ASTM E 29 : 2013 : R2019 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
ASTM D 6299 : 2017 : REV A Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 6299 : 2017 : REV B Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 6299 : 2009 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM F 2576 : 2013 Standard Terminology Relating to Declarable Substances in Materials
ASTM D 6299 : 2013 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 3641 : 2002 Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
ASTM D 6299 : 2021 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM E 135 : 2023 Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials
ASTM E 1361 : 2002 : R2021 Standard Guide for Correction of Interelement Effects in X-Ray Spectrometric Analysis
ASTM E 29 : 2002 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
ASTM D 6299 : 2010 : EDT 1 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 6299 : 2022 : EDT 1 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM E 135 : 2021 : REV A Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials
ASTM F 2576 : 2008 Standard Terminology Relating to Declarable Substances in Materials
ASTM D 4703 : 2003 Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
ASTM D 883 : 2022 Standard Terminology Relating to Plastics
ASTM D 883 : 2020 : REV B Standard Terminology Relating to Plastics
ASTM F 2576 : 2007 : REV A Standard Terminology Relating to Declarable Substances in Materials
ASTM E 691 : 2020 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 4703 : 1993 Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
ASTM D 3641 : 2021 Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
ASTM E 1361 : 1990 : R1999 Standard Guide for Correction of Interelement Effects in X-Ray Spectrometric Analysis
ASTM F 2576 : 2011 Standard Terminology Relating to Declarable Substances in Materials
ASTM D 3641 : 2010 Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
ASTM D 6299 : 2000 Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance
ASTM F 2576 : 2015 Standard Terminology Relating to Declarable Substances in Materials
ASTM D 6299 : 2010 : EDT 2 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM F 2576 : 2006 : EDT 1 Standard Terminology Relating to Declarable Substances in Materials
ASTM D 6299 : 2016 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM E 1361 : 2002 : R2007 Standard Guide for Correction of Interelement Effects in X-Ray Spectrometric Analysis
ASTM E 691 : 2019 : EDT 1 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 135 : 2003 : REV B Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials
ASTM E 691 : 2023 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 4703 : 2010 Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
ASTM E 1361 : 2002 Standard Guide for Correction of Interelement Effects in X-Ray Spectrometric Analysis
ASTM E 135 : 2023 : REV A Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials
ASTM D 6299 : 2019 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 3641 : 2015 Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
ASTM D 3641 : 2010 : REV A Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
ASTM D 6299 : 2023 : EDT 1 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 6299 : 2000 : REV A Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance
ASTM D 3641 : 2014 Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
ASTM E 691 : 2022 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 691 : 2009 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 135 : 2002 : REV A Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials
ASTM E 1361 : 2002 : R2014 : EDT 1 Standard Guide for Correction of Interelement Effects in X-Ray Spectrometric Analysis
ASTM E 135 : 2022 : REV B Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials
ASTM D 6299 : 2023 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 6299 : 2020 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM F 2576 : 2006 Standard Terminology Relating to Declarable Substances in Materials
ASTM D 6299 : 2008 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 6299 : 2002 : EDT 1 Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance
ASTM E 691 : 2021 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 135 : 2022 : REV A Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials
ASTM F 2576 : 2015 : REV A Standard Terminology Relating to Declarable Substances in Materials (Withdrawn 2024)
ASTM D 6299 : 2022 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM E 135 : 2021 Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials
ASTM E 135 : 2003 Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials
ASTM E 135 : 2003 : REV C Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials
ASTM D 4703 : 2000 Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
ASTM D 4703 : 2010 : REV A Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
ASTM E 135 : 2022 Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials
ASTM D 4703 : 2016 Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
ASTM F 2576 : 2009 Standard Terminology Relating to Declarable Substances in Materials
ASTM D 3641 : 1997 Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
ASTM D 6299 : 2007 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 6299 : 2007 : EDT 1 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 6299 : 2020 : REV A Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM E 135 : 2020 : REV B Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials
ASTM D 3641 : 2012 Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
ASTM D 6299 : 2017 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
ASTM D 4703 : 2007 Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
ASTM D 6299 : 2002 Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance
ASTM E 29 : 2022 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

View more information
£69.29
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.