• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM F 2882/F2882M : 2017

Current
Current

The latest, up-to-date edition.

Standard Specification for Screws, Alloy Steel, Heat Treated, 170 ksi and 1170 MPa Minimum Tensile Strength (Inch and Metric)
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-06-2017

1.1This specification covers the requirements for quenched and tempered alloy steel screws 0.060 through 11/2in. and 1.6 through 48 mm in diameter having a minimum ultimate tensile strength of 170 KSI or 1170 MPa.

1.2The values are stated in inch-pound units for inch fasteners and SI metric units for metric fasteners. The values stated in each system may not be exact equivalents; therefore each system shall be used independently of the other. Combining values from the two systems may result in non-conformance to the standard.

1.3The following hazard caveat pertains only to the test method portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
F 16
DocumentType
Standard
Pages
7
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

ASTM F 1940 : 2007 : REV A : R2014 Standard Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners
ASTM F 1470 : 2012 Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
ASTM F 2328 : 2005 : R2011 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs
ASTM F 606/F606M : 2019 Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
ASTM F 1470 : 2002 Standard Guide for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
ASTM F 1470 : 2009 Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
ASTM F 2282 : 2018 Standard Specification for Quality Assurance Requirements for Carbon and Alloy Steel Wire, Rods, and Bars for Mechanical Fasteners
ASTM F 2282 : 2003 : R2015 Standard Specification for Quality Assurance Requirements for Carbon and Alloy Steel Wire, Rods, and Bars for Mechanical Fasteners
ASTM F 2328M : 2004 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs [Metric]
ASTM F 2328M : 2006 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs [Metric]
ASTM F 2328M : 2007 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs [Metric]
ASTM F 2328M : 2017 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts (Metric)
ASTM F 2282 : 2003 : R2009 : EDT 1 Standard Specification for Quality Assurance Requirements for Carbon and Alloy Steel Wire, Rods, and Bars for Mechanical Fasteners
ASTM F 2328M : 2017 : R2022 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts (Metric)
ASTM F 2328M : 2007 : R2014 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs (Metric)
ASTM A 751 : 2021 Standard Test Methods and Practices for Chemical Analysis of Steel Products
ASTM F 788/F788M : 2020 : EDT 1 Standard Specification for Surface Discontinuities of Bolts, Screws, Studs, and Rivets, Inch and Metric Series
ASTM F 2282 : 2003 Standard Specification for Quality Assurance Requirements for Carbon and Alloy Steel Wire, Rods, and Bars for Mechanical Fasteners
ASTM F 2328 : 2017 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts
ASTM F 1940 : 2001 Standard Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners
ASTM F 2328 : 2004 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs
ASTM F 2328 : 2014 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts
ASTM F 788/F788M : 1997 Standard Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series
ASTM F 1940 : 2007 : REV A Standard Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners
ASTM A 751 : 2020 Standard Test Methods and Practices for Chemical Analysis of Steel Products
ASTM F 2328M : 2005 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs [Metric]
ASTM F 2328M : 2017 : R2022 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts (Metric)
ASTM F 1470 : 2018 Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
ASTM F 2328 : 2005 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs
ASTM F 1470 : 2001 Standard Guide for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
ASTM F 1470 : 2019 Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
ASTM F 1470 : 2024 Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
ASTM F 2282 : 2003 : R2009 Standard Specification for Quality Assurance Requirements for Carbon and Alloy Steel Wire, Rods, and Bars for Mechanical Fasteners
ASTM F 2328 : 2017 : R2022 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts
ASTM E 112 : 2013 : R2021 Standard Test Methods for Determining Average Grain Size
ASTM E 112 : 2013 Standard Test Methods for Determining Average Grain Size
ASTM F 1940 : 2007 : REV A : R2019 Standard Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners
ASTM F 2282 : 2015 Standard Specification for Quality Assurance Requirements for Carbon and Alloy Steel Wire, Rods, and Bars for Mechanical Fasteners
ASTM F 2328M : 2007 : R2013 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs (Metric)
ASTM F 1940 : 2007 Standard Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners
ASTM F 606/F606M : 2021 Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
ASTM F 2328M : 2014 Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts (Metric)
ASTM F 2282 : 2023 Standard Specification for Quality Assurance Requirements for Carbon and Alloy Steel Wire, Rods, and Bars for Mechanical Fasteners
ASTM F 1940 : 1999 Standard Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners

View more information
£52.59
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.