• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM F 2945 : 2018

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Polyamide 11 Gas Pressure Pipe, Tubing, and Fittings
Available format(s)

Hardcopy , PDF

Superseded date

18-11-2023

Language(s)

English

Published date

13-11-2018

This specification covers requirements and test methods for the characterization of polyamide 11 pipe, tubing, and fittings for use in fuel gas pipelines.

1.1This specification covers requirements and test methods for the characterization of polyamide 11 pipe, tubing, and fittings for use in fuel gas pipelines. The pipe and fittings covered by this specification are intended for use in the distribution and transmission of fuel gases.

1.1.1This specification does not cover threaded pipe. Generic fusion guidelines are given in Appendix X1. Design considerations are discussed in Appendix X2. In-plant quality control programs are specified in Annex A1.

1.2The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.

Note 1:Heat fusion joining of PA11 pipe and fittings meeting the requirements of this standard is limited to PA11 pipe and fittings meeting the requirements of this standard. Heat Fusion joining of PA11 pipe and fittings meeting the requirements of this standard is not allowed to pipes and fittings made from any other thermoplastic materials (for example, PA12, PEs, PVCs, etc.).

1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4The following is an index of the annexes and appendixes in this specification:

Annexes

Subject

Annex A1

In-Plant Quality Control for sizes up to 12 in.

Annex A2

PA-11 Butt Fusion Fittings

Appendixes

Subject

Appendix X1

Butt Fusion Guidelines for PA-11 Piping

Appendix X2

Design Consideration

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
F 17
DocumentType
Standard
Pages
15
ProductNote
THIS STANDARD ALSO REFERS TO B16.40
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM F 2145 : 2023 Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing
ASTM F 3508 : 2021 : REV A Standard Guide for In-Situ Pipeline Renovation As Dual-Wall Composite Pipeline by Push/Pull Installation of Compressed-Fit Shape-Memory-Polymer Tubular (SMPT)
ASTM F 3124 : 2023 : REV A Standard Practice for Data Recording the Procedure used to Produce Heat Butt Fusion Joints in Plastic Piping Systems or Fittings
ASTM F 1733 : 2020 Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing
ASTM F 1948 : 2020 Standard Specification for Metallic Mechanical Fittings for Use on Outside Diameter Controlled Thermoplastic Gas Distribution Pipe and Tubing
ASTM F 1973 : 2013 : R2018 Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems
ASTM F 2145 : 2013 : R2018 Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing
ASTM F 1733 : 2013 Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing
ASTM F 1948 : 2015 Standard Specification for Metallic Mechanical Fittings for Use on Outside Diameter Controlled Thermoplastic Gas Distribution Pipe and Tubing
ASTM F 3124 : 2015 : EDT 1 Standard Practice for Data Recording the Procedure used to Produce Heat Butt Fusion Joints in Plastic Piping Systems or Fittings
ASTM F 2509 : 2015 : R2019 Standard Specification for Field-assembled Anodeless Riser Kits for Use on Outside Diameter Controlled Polyethylene and Polyamide-11 (PA11) Gas Distribution Pipe and Tubing

ASTM F 1563 : 2001 : R2007 Standard Specification for Tools to Squeeze-off Polyethylene (PE) Gas Pipe or Tubing
ASTM D 2837 : 2013 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM D 1600 : 1999 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 2774 : 2004 Standard Practice for Underground Installation of Thermoplastic Pressure Piping
ASTM D 4066 : 2000 Standard Classification System for Nylon Injection and Extrusion Materials (PA)
ASTM F 2897 : 2023 : REV A Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances)
ASTM F 1563 : 2001 : R2011 Standard Specification for Tools to Squeeze-off Polyethylene (PE) Gas Pipe or Tubing
ASTM F 1733 : 2020 Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing
ASTM F 2897 : 2011 Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances)
ASTM D 2290 : 2016 Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe
ASTM D 1598 : 2002 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM D 2774 : 2021 Standard Practice for Underground Installation of Thermoplastic Pressure Piping
ASTM D 3418 : 2012 : EDT 1 Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
ASTM D 2122 : 1998 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 2290 : 2019 : REV A Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe
ASTM D 3418 : 1982 : R1988 : EDT 1 Standard Test Method for Transition Temperatures of Polymers By Thermal Analysis
ASTM D 1598 : 2015 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM F 412 : 2020 : REV A Standard Terminology Relating to Plastic Piping Systems
ASTM D 3418 : 1999 Standard Test Method for Transition Temperatures of Polymers By Differential Scanning Calorimetry
ASTM D 1598 : 2015 : REV A Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM D 2774 : 2021 : REV A Standard Practice for Underground Installation of Thermoplastic Pressure Piping
ASTM F 412 : 2021 Standard Terminology Relating to Plastic Piping Systems
ASTM F 1733 : 1996 : R2002 Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing
ASTM F 2145 : 2023 Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing
ASTM D 2837 : 2001 : REV A Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
ASTM D 3418 : 2021 Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
ASTM F 2600 : 2009 : R2023 Standard Specification for Electrofusion Type Polyamide-11 Fittings for Outside Diameter Controlled Polyamide-11 Pipe and Tubing
ASTM F 2897 : 2014 Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances)
ASTM D 4066 : 2001 : REV A : R2008 Standard Classification System for Nylon Injection and Extrusion Materials (PA) (Withdrawn 2012)
ASTM F 2138 : 2001 : EDT 1 Standard Specification for Excess Flow Valves for Natural Gas Service
ASTM F 1563 : 1994 : R2000 Standard Specification for Tools to Squeeze-off Polyethylene (PE) Gas Pipe or Tubing
ASTM F 2600 : 2009 Standard Specification for Electrofusion Type Polyamide-11 Fittings for Outside Diameter Controlled Polyamide-11 Pipe and Tubing
ASTM F 1025 : 1994 : R2006 Standard Guide for Selection and Use of Full-Encirclement-Type Band Clamps for Reinforcement or Repair of Punctures or Holes in Polyethylene Gas Pressure Pipe
ASTM D 2774 : 2001 Standard Practice for Underground Installation of Thermoplastic Pressure Piping
ASTM D 1598 : 2023 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM F 2897 : 2011 : REV A : EDT 1 Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances)
ASTM F 1973 : 2021 Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems
ASTM F 2145 : 2013 : R2018 Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing
ASTM D 2837 : 2002 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
ASTM D 2837 : 2001 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
ASTM D 2837 : 2004 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM F 2138 : 2001 Standard Specification for Excess Flow Valves for Natural Gas Service
ASTM D 2837 : 2021 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM D 4066 : 2001 : REV A Standard Classification System for Nylon Injection and Extrusion Materials (PA)
ASTM F 2897 : 2021 Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances)
ASTM D 2774 : 1994 Standard Practice for Underground Installation of Thermoplastic Pressure Piping
ASTM D 543 : 2021 Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
ASTM D 1600 : 2007 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM F 1733 : 1996 : EDT 1 Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing
ASTM D 1600 : 2013 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 3418 : 2012 Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
ASTM F 2138 : 2012 : R2017 Standard Specification for Excess Flow Valves for Natural Gas Service
ASTM F 2600 : 2009 : R2013 Standard Specification for Electrofusion Type Polyamide-11 Fittings for Outside Diameter Controlled Polyamide-11 Pipe and Tubing
ASTM D 2290 : 2004 Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe by Split Disk Method
ASTM F 2145 : 2001 : R2007 Standard Specification for Polyamide 11 (PA 11) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 Pipe and Tubing
ASTM D 1600 : 2014 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 2837 : 2008 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM D 2837 : 1998 : REV A Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
ASTM D 3418 : 2003 Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
ASTM D 2774 : 2020 Standard Practice for Underground Installation of Thermoplastic Pressure Piping
ASTM F 2138 : 2012 Standard Specification for Excess Flow Valves for Natural Gas Service
ASTM D 1600 : 2008 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 3418 : 2015 Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
ASTM F 2145 : 2001 Standard Specification for Polyamide 11 (PA 11) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 Pipe and Tubing
ASTM F 2145 : 2009 Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing
ASTM F 1025 : 1994 : R2000 Standard Guide for Selection and Use of Full-Encirclement-Type Band Clamps for Reinforcement or Repair of Punctures or Holes in Polyethylene Gas Pressure Pipe
ASTM D 1598 : 1997 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM D 2774 : 2008 Standard Practice for Underground Installation of Thermoplastic Pressure Piping
ASTM D 2837 : 2001 : REV A : EDT 1 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
ASTM D 2837 : 2011 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM D 4066 : 2013 : R2019 Standard Classification System for Nylon Injection and Extrusion Materials (PA)
ASTM D 1599 : 2014 Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
ASTM D 1599 : 2014 : EDT 1 Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
ASTM F 2600 : 2006 Standard Specification for Electrofusion Type Polyamide-11 Fittings for Outside Diameter Controlled Polyamide-11 Pipe and Tubing
ASTM F 2897 : 2015 : REV A Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances)
ASTM D 4066 : 2001 Standard Classification System for Nylon Injection and Extrusion Materials (PA)
ASTM F 1973 : 2012 Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems
ASTM D 1898 : 1968 : R1989 Standard Practice for Sampling of Plastics (Withdrawn 1998)
ASTM D 2122 : 1998 : EDT 1 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM F 1973 : 2008 Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems
ASTM D 1599 : 2018 Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
ASTM D 2837 : 2022 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM F 1973 : 2005 Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) Fuel Gas Distribution Systems
ASTM D 1599 : 1999 : R2011 Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
ASTM D 2290 : 2000 Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe by Split Disk Method
ASTM F 1973 : 2002 Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) Fuel Gas Distribution Systems
ASTM D 4066 : 1994 : REV B Standard Classification System for Nylon Injection and Extrusion Materials (PA)
ASTM D 638 : 2014 Standard Test Method for Tensile Properties of Plastics
ASTM D 4066 : 2013 Standard Classification System for Nylon Injection and Extrusion Materials (PA)
ASTM D 1599 : 1999 : EDT 1 Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings
ASTM F 1733 : 2007 Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing
ASTM F 1025 : 1994 : R2011 Standard Guide for Selection and Use of Full-Encirclement-Type Band Clamps for Reinforcement or Repair of Punctures or Holes in Polyethylene Gas Pressure Pipe
ASTM F 1973 : 2013 Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems
ASTM D 2122 : 2022 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 1600 : 2018 Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
ASTM F 1973 : 2013 : EDT 1 Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems
ASTM D 543 : 2020 Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
ASTM F 1973 : 2013 : R2018 Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems
ASTM D 618 : 2013 Standard Practice for Conditioning Plastics for Testing
ASTM F 2897 : 2023 Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances)
ASTM F 2897 : 2015 Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances)
ASTM F 412 : 2023 Standard Terminology Relating to Plastic Piping Systems
ASTM D 1598 : 2021 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM D 3418 : 2008 Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
ASTM F 1733 : 1996 Standard Specification for Butt heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing
ASTM D 1598 : 2002 : R2008 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM F 2600 : 2009 : R2018 Standard Specification for Electrofusion Type Polyamide-11 Fittings for Outside Diameter Controlled Polyamide-11 Pipe and Tubing
ASTM F 2145 : 2013 Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing
ASTM D 2290 : 2000 : EDT 1 Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe by Split Disk Method
ASTM D 2122 : 1998 : R2004 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 2122 : 2016 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM F 2138 : 2009 Standard Specification for Excess Flow Valves for Natural Gas Service
ASTM D 2774 : 2012 Standard Practice for Underground Installation of Thermoplastic Pressure Piping
ASTM D 2290 : 2019 Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe
ASTM F 1973 : 1999 : EDT 2 Standard Specification for Factory Assebled Anodeless Risers and Transition Fittings in Polyethylene (PE) Fuel Gas Distribution Systems
ASTM F 1563 : 2001 Standard Specification for Tools to Squeeze-off Polyethylene (PE) Gas Pipe or Tubing
ASTM D 4066 : 2000 : REV A Standard Classification System for Nylon Injection and Extrusion Materials (PA)
ASTM F 1733 : 2013 Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing
ASTM D 1599 : 1999 : R2005 Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
ASTM D 1598 : 2002 : R2009 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
ASTM D 2290 : 2012 Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe
ASTM F 1973 : 1999 : EDT 1 Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) Fuel Gas Distribution Systems
ASTM F 1563 : 2001 : R2019 Standard Specification for Tools to Squeeze-off Polyethylene (PE) Gas Pipe or Tubing
ASTM F 1973 : 1999 Standard Specification for Factory Assebled Anodeless Risers and Transition Fittings in Polyethylene (PE) Fuel Gas Distribution Systems
ASTM F 2897 : 2011 : REV A Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances)
ASTM D 2774 : 2004 : EDT 1 Standard Practice for Underground Installation of Thermoplastic Pressure Piping
ASTM D 2122 : 1998 : R2010 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 2290 : 2008 Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe by Split Disk Method
ASTM D 4066 : 1996 Standard Classification System for Nylon Injection and Extrusion Materials (PA)
ASTM D 1599 : 1999 Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings
ASTM D 618 : 2021 Standard Practice for Conditioning Plastics for Testing
ASTM F 1025 : 2019 Standard Guide for Selection and Use of Full-Encirclement-Type Band Clamps for Reinforcement or Repair of Punctures or Holes in Polyethylene Gas Pressure Pipe
ASTM D 2122 : 2015 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 638 : 2022 Standard Test Method for Tensile Properties of Plastics
ASTM D 2837 : 2013 : EDT 1 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
ASTM D 2837 : 2004 : EDT 1 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products

View more information
£69.29
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.