ASTM F 3101 : 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Specification for Unsupervised Public Use Outdoor Fitness Equipment
Hardcopy , PDF
13-08-2021
English
12-05-2015
CONTAINED IN VOL. 15.07, 2015 Defines parameters for the design and manufacture of outdoor fitness equipment.
1.1This specification establishes parameters for the design and manufacture of outdoor fitness equipment as defined in 3.1.30.
1.2It is intended that these fitness products will be used in an unsupervised outdoor setting or environment and will be permanently anchored.
1.2.1It is the intent of this specification to only specify requirements for outdoor fitness equipment and its installation and not the design of the facility or grounds on which the products are to be installed.
1.3The specifications set forth in this standard are intended to minimize the likelihood of serious injuries.
1.3.1The specifications set forth in this standard are for outdoor fitness equipment intended for use in an unsupervised setting by individuals age 13 and older.
1.4The values stated in SI (metric) units are to be regarded as standard. The values in parentheses are for information only.
1.5General Measures, Tolerances, and Conversions:
1.5.1The general tolerances for this specification (unless otherwise specified) are as follows:
| Dimension | Tolerance |
| X mm (X in.) | ± 13.0 mm (0.5 in.) |
| X.X mm (X.X in.) | ±1.3 mm (0.05 in.) |
| X.XX mm (X.XX in.) | ±.0.130 mm (0.005 in.) |
1.5.2These tolerances still apply to a dimension even when terms like greater than, less than, minimum, or maximum are used.
1.6This standard is to be used in conjunction with Test Methods F2571 and Specification F2276. If a design or installation concern is not addressed in this specification then the applicable requirements of Specification F2276 shall be used.
1.6.1This standard takes precedence over Specification F2276 and Test Methods F2571 in areas that are addressed in this document.
1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| Committee |
F 08
|
| DocumentType |
Standard
|
| Pages |
25
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
| ASTM F 1749 : 1996 | Standard Specification for Fitness Equipment and Fitness Facility Safety Signage and Labels |
| ASTM D 2240 : 2000 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM F 1951 : 2008 | Standard Specification for Determination of Accessibility of Surface Systems Under and Around Playground Equipment |
| ASTM F 1918 : 1998 | Standard Safety Performance Specification for Soft Contained Play Equipment |
| ASTM F 1918 : 2010 | Standard Safety Performance Specification for Soft Contained Play Equipment |
| ASTM F 1951 : 1999 | Standard Specification for Determination of Accessibility of Surface Systems Under and Around Playground Equipment |
| ASTM F 893 : 1987 : R2000 | Standard Guide for Inspection of Amusement Rides and Devices |
| ASTM F 3021 : 2013 | Standard Specification for Universal Design of Fitness Equipment for Inclusive Use by Persons with Functional Limitations and Impairments |
| ASTM F 1292 : 2018 : EDT 1 | Standard Specification for Impact Attenuation of Surfacing Materials Within the Use Zone of Playground Equipment |
| ASTM F 1292 : 2017 | Standard Specification for Impact Attenuation of Surfacing Materials Within the Use Zone of Playground Equipment |
| ASTM F 846 : 1992 : R1998 | Standard Guide for Testing Performance of Amusement Rides and Devices |
| ASTM F 1004 : 2002 | Standard Consumer Safety Specification for Expansion Gates and Expandable Enclosures |
| ASTM F 3021 : 2017 : REDLINE | Standard Specification for Universal Design of Fitness Equipment for Inclusive Use by Persons with Functional Limitations and Impairments |
| ASTM F 1004 : 2015 | Standard Consumer Safety Specification for Expansion Gates and Expandable Enclosures |
| ASTM F 1159 : 1997 : REV A | Standard Practice for the Design and Manufacture of Amusement Rides and Devices |
| ASTM F 2276 : 2010 | Standard Specification for Fitness Equipment |
| ASTM F 1004 : 2019 | Standard Consumer Safety Specification for Expansion Gates and Expandable Enclosures |
| ASTM F 1918 : 2012 : R2017 | Standard Safety Performance Specification for Soft Contained Play Equipment |
| ASTM F 1004 : 2000 | Standard Consumer Safety Specification for Expansion Gates and Expandable Enclosures |
| ASTM F 2276 : 2003 | Standard Specification for Fitness Equipment |
| ASTM F 3021 : 2016 | Standard Specification for Universal Design of Fitness Equipment for Inclusive Use by Persons with Functional Limitations and Impairments |
| ASTM D 2240 : 2004 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM F 3022 : 2013 | Standard Test Method for Evaluating the Universal Design of Fitness Equipment for Inclusive Use by Persons with Functional Limitations and Impairments |
| ASTM F 1159 : 2015 | Standard Practice for Design of Amusement Rides and Devices that are Outside the Purview of Other F24 Design Standards |
| ASTM F 963 : 2007 | Standard Consumer Safety Specification for Toy Safety |
| ASTM F 2571 : 2009 | Standard Test Methods for Evaluating Design and Performance Characteristics of Fitness Equipment |
| ASTM F 1004 : 2015 : REV A | Standard Consumer Safety Specification for Expansion Gates and Expandable Enclosures |
| ASTM F 1749 : 2009 | Standard Specification for Fitness Equipment and Fitness Facility Safety Signage and Labels |
| ASTM F 1749 : 2015 : REDLINE | Standard Specification for Fitness Equipment and Fitness Facility Safety Signage and Labels |
| ASTM F 2571 : 2015 | Standard Test Methods for Evaluating Design and Performance Characteristics of Fitness Equipment |
| ASTM F 1159 : 2003 : REV A | Standard Practice for Design and Manufacture of Patron Directed, Artificial Climbing Walls, Dry Slide, Coin Operated and Purposeful Water Immersion Amusement Rides and Devices and Air-Supported Structures |
| ASTM F 1292 : 2013 | Standard Specification for Impact Attenuation of Surfacing Materials Within the Use Zone of Playground Equipment |
| ASTM D 2240 : 2004 : EDT 1 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM F 1951 : 2009 | Standard Specification for Determination of Accessibility of Surface Systems Under and Around Playground Equipment |
| ASTM F 1292 : 2009 | Standard Specification for Impact Attenuation of Surfacing Materials within the Use Zone of Playground Equipment |
| ASTM F 1292 : 2004 | Standard Specification for Impact Attenuation of Surfacing Materials within the Use Zone of Playground Equipment |
| ASTM F 3021 : 2014 | Standard Specification for Universal Design of Fitness Equipment for Inclusive Use by Persons with Functional Limitations and Impairments |
| ASTM F 3022 : 2016 : EDT 1 | Standard Test Method for Evaluating the Universal Design of Fitness Equipment for Inclusive Use by Persons with Functional Limitations and Impairments |
| ASTM F 1159 : 2002 | Standard Practice for the Design and Manufacture of Amusement Rides and Devices |
| ASTM F 1749 : 2015 : R2020 | Standard Specification for Fitness Equipment and Fitness Facility Safety Signage and Labels |
| ASTM F 1077 : 1995 : REV A | Standard Guide for Selection of Committee F-16 Fastener Specifications |
| ASTM F 1004 : 2016 : REV B | Standard Consumer Safety Specification for Expansion Gates and Expandable Enclosures |
| ASTM F 3021 : 2015 | Standard Specification for Universal Design of Fitness Equipment for Inclusive Use by Persons with Functional Limitations and Impairments |
| ASTM F 1159 : 2011 | Standard Practice for Design and Manufacture of Patron Directed, Artificial Climbing Walls, Dry Slide, Coin Operated and Purposeful Water Immersion Amusement Rides and Devices and Air-Supported Structures |
| ASTM F 1004 : 2016 | Standard Consumer Safety Specification for Expansion Gates and Expandable Enclosures |
| ASTM F 1077 : 1995 : REV A : R2002 | Standard Guide for Selection of Committee F16 Fastener Specifications |
| ASTM F 1951 : 2009 : REV A | Standard Specification for Determination of Accessibility of Surface Systems Under and Around Playground Equipment |
| ASTM F 2571 : 2015 : R2020 | Standard Test Methods for Evaluating Design and Performance Characteristics of Fitness Equipment |
| ASTM F 1951 : 2014 | Standard Specification for Determination of Accessibility of Surface Systems Under and Around Playground Equipment |
| ASTM D 2240 : 2002 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM F 1159 : 2016 | Standard Practice for Design of Amusement Rides and Devices that are Outside the Purview of Other F24 Design Standards |
| ASTM F 1004 : 1998 | Standard Consumer Safety Specification for Expansion Gates and Expandable Enclosures |
| ASTM F 1004 : 2018 | Standard Consumer Safety Specification for Expansion Gates and Expandable Enclosures |
| ASTM D 2240 : 2015 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM F 1004 : 2009 | Standard Consumer Safety Specification for Expansion Gates and Expandable Enclosures |
| ASTM D 2240 : 2003 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM F 1004 : 2004 | Standard Consumer Safety Specification for Expansion Gates and Expandable Enclosures |
| ASTM F 1918 : 2004 | Standard Safety Performance Specification for Soft Contained Play Equipment |
| ASTM F 2276 : 2009 | Standard Specification for Fitness Equipment |
| ASTM D 2240 : 2002 : REV B | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM F 1292 : 1999 | Standard Specification for Impact Attenuation of Surface Systems Under and Around Playground Equipment |
| ASTM F 3022 : 2015 | Standard Test Method for Evaluating the Universal Design of Fitness Equipment for Inclusive Use by Persons with Functional Limitations and Impairments |
| ASTM F 1292 : 2018 | Standard Specification for Impact Attenuation of Surfacing Materials Within the Use Zone of Playground Equipment |
| ASTM F 3021 : 2017 | Standard Specification for Universal Design of Fitness Equipment for Inclusive Use by Persons with Functional Limitations and Impairments |
| ASTM F 1292 : 2017 : REV A | Standard Specification for Impact Attenuation of Surfacing Materials Within the Use Zone of Playground Equipment |
| ASTM F 3022 : 2014 | Standard Test Method for Evaluating the Universal Design of Fitness Equipment for Inclusive Use by Persons with Functional Limitations and Impairments |
| ASTM D 2240 : 2015 : EDT 1 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM F 1159 : 2003 | Standard Practice for the Design and Manufacture of Amusement Rides and Devices |
| ASTM F 1159 : 2014 | Standard Practice for Design of Amusement Rides and Devices that are Outside the Purview of Other F24 Design Standards |
| ASTM F 1159 : 2016 : EDT 1 | Standard Practice for Design of Amusement Rides and Devices that are Outside the Purview of Other F24 Design Standards |
| ASTM F 1004 : 2021 | Standard Consumer Safety Specification for Expansion Gates and Expandable Enclosures |
| ASTM F 1077 : 2005 | Standard Guide for Selection of Committee F16 Fastener Specifications (Withdrawn 2014) |
| ASTM D 2240 : 2005 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM F 1159 : 2015 : REV A | Standard Practice for Design of Amusement Rides and Devices that are Outside the Purview of Other F24 Design Standards |
| ASTM F 2276 : 2005 | Standard Specification for Fitness Equipment |
| ASTM F 1749 : 2002 | Standard Specification for Fitness Equipment and Fitness Facility Safety Signage and Labels |
| ASTM F 1159 : 2015 : REV B | Standard Practice for Design of Amusement Rides and Devices that are Outside the Purview of Other F24 Design Standards |
| ASTM D 2240 : 2005 : R2010 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM F 1749 : 2015 | Standard Specification for Fitness Equipment and Fitness Facility Safety Signage and Labels |
| ASTM F 1004 : 2007 | Standard Consumer Safety Specification for Expansion Gates and Expandable Enclosures |
| ASTM F 3022 : 2016 | Standard Test Method for Evaluating the Universal Design of Fitness Equipment for Inclusive Use by Persons with Functional Limitations and Impairments |
| ASTM F 2276 : 2010 : R2015 | Standard Specification for Fitness Equipment |
| ASTM D 2240 : 2002 : REV A | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM F 1004 : 2013 | Standard Consumer Safety Specification for Expansion Gates and Expandable Enclosures |
| ASTM F 1951 : 2009 : REV B | Standard Specification for Determination of Accessibility of Surface Systems Under and Around Playground Equipment |
| ASTM F 1004 : 2012 | Standard Consumer Safety Specification for Expansion Gates and Expandable Enclosures |
| ASTM F 1004 : 2010 | Standard Consumer Safety Specification for Expansion Gates and Expandable Enclosures |
| ASTM F 1004 : 2016 : REV A | Standard Consumer Safety Specification for Expansion Gates and Expandable Enclosures |
| ASTM F 1918 : 2012 | Standard Safety Performance Specification for Soft Contained Play Equipment |
| ASTM F 1951 : 2014 : REDLINE | Standard Specification for Determination of Accessibility of Surface Systems Under and Around Playground Equipment |
| ASTM F 2571 : 2015 : REDLINE | Standard Test Methods for Evaluating Design and Performance Characteristics of Fitness Equipment |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.