We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • ASTM F 3273 : 2017

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    Standard Specification for Wrought Molybdenum-47.5 Rhenium Alloy for Surgical Implants (UNS R03700)

    Available format(s):  Hardcopy, PDF

    Superseded date:  06-01-2022

    Language(s):  English

    Published date:  18-09-2017

    Publisher:  American Society for Testing and Materials

    Add to Watchlist

    Add To Cart

    Abstract - (Show below) - (Hide below)

    This specification covers the chemical, mechanical, and metallurgical requirements for wrought molybdenum-47.5 rhenium alloy to be used in the manufacture of surgical implants.

    Scope - (Show below) - (Hide below)

    1.1This specification covers the chemical, mechanical, and metallurgical requirements for wrought molybdenum-47.5 rhenium alloy to be used in the manufacture of surgical implants.

    1.2The SI units in this standard are the primary units. The values stated in either primary SI units or secondary inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

    1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    General Product Information - (Show below) - (Hide below)

    Committee F 04
    Document Type Standard
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    ASTM E 1941 : 2010 : R2016 Standard Test Method for Determination of Carbon in Refractory and Reactive Metals and Their Alloys by Combustion Analysis
    ASTM E 228 : 2017 : REDLINE Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer
    ASTM E 8/E8M : 2016 : REV A : EDT 1 Standard Test Methods for Tension Testing of Metallic Materials
    ASTM E 1941 : 2010 Standard Test Method for Determination of Carbon in Refractory and Reactive Metals and Their Alloys by Combustion Analysis
    ASTM E 1621 : 2013 Standard Guide for Elemental Analysis by Wavelength Dispersive X-Ray Fluorescence Spectrometry
    SAE AMS 2630 : 2010 INSPECTION, ULTRASONIC, PRODUCT OVER 0.5 INCH (12.7 MM) THICK
    ASTM E 8/E8M : 2021 Standard Test Methods for Tension Testing of Metallic Materials
    SAE AMS 2632 : 1995 INSPECTION, ULTRASONIC, OF THIN MATERIALS 0.5 INCH (12.77 MM) AND UNDER IN CROSS-SECTIONAL THICKNESS
    ASTM E 29 : 2002 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
    ASTM B 311 : 2017 : REDLINE Standard Test Method for Density of Powder Metallurgy (PM) Materials Containing Less Than Two Percent Porosity
    ASTM E 1621 : 2005 Standard Guide for X-Ray Emission Spectrometric Analysis
    ISO 6892-1:2016 Metallic materials Tensile testing Part 1: Method of test at room temperature
    ASTM B 311 : 1993 : R1997 Test Method for Density Determination for Powder Metallurgy (P/M) Materials Containing Less Than Two Percent Porosity
    IEEE/ASTM SI 10 : 2010 METRIC PRACTICE
    ASTM E 2626 : 2008 Standard Guide for Spectrometric Analysis of Reactive and Refractory Metals
    ASTM E 1621 : 2021 Standard Guide for Elemental Analysis by Wavelength Dispersive X-Ray Fluorescence Spectrometry
    ISO 10993-10:2010 Biological evaluation of medical devices Part 10: Tests for irritation and skin sensitization
    ISO 10993-11:2017 Biological evaluation of medical devices Part 11: Tests for systemic toxicity
    ASTM E 1941 : 2004 Standard Test Method for Determination of Carbon in Refractory and Reactive Metals and Their Alloys
    ASTM E 1621 : 2013 : REDLINE Standard Guide for Elemental Analysis by Wavelength Dispersive X-Ray Fluorescence Spectrometry
    ISO 9001:2015 Quality management systems Requirements
    ASTM E 2626 : 2008 : EDT 1 Standard Guide for Spectrometric Analysis of Reactive and Refractory Metals (Withdrawn 2017)
    ASTM E 290 : 2014 : REDLINE Standard Test Methods for Bend Testing of Material for Ductility
    ASTM B 193 : 2016 : REDLINE Standard Test Method for Resistivity of Electrical Conductor Materials
    ASTM E 1621 : 1994 : R1999 Standard Guide for X-Ray Emission Spectrometric Analysis
    ASTM E 1941 : 1998 Standard Test Method for Determination of Carbon in Refractory and Reactive Metals and Their Alloys
    ASTM B 774 : 2000 : R2014 Standard Specification for Low Melting Point Alloys
    ISO 10993-6:2016 Biological evaluation of medical devices Part 6: Tests for local effects after implantation
    ASTM E 8/E8M : 2016-09 TEST METHODS FOR TENSION TESTING OF METALLIC MATERIALS
    ASTM C 1113 : 1999 Standard Test Method for Thermal Conductivity of Refractories by Hot Wire (Platinum Resistance Thermometer Technique)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective