ASTM F 790 : 2018
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Guide for Testing Materials for Aerospace Plastic Transparent Enclosures
Available format(s)
Hardcopy , PDF
Superseded date
13-02-2023
Language(s)
English
Published date
18-06-2018
This guide is intended to summarize the standard test methods available on individual and composite materials utilized in fabrication of aerospace plastic transparent enclosures.
1.1This guide is intended to summarize the standard test methods available on individual and composite materials utilized in fabrication of aerospace plastic transparent enclosures. As such, it is intended to specifically include transparent thermoplastics, transparent elastomers, and reinforced plastics, whether thermoplastic or thermosetting.
1.2This guide is intended as an aid in the search for test methods pertinent to Aerospace Plastic Transparent Enclosures. It should be understood that all methods listed may not apply to all enclosures.
1.3The standards included refer to the properties or aspects listed in Table 1. The properties or aspects are listed in alphabetical order and the descriptions used are intended to facilitate the search.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
F 07
|
| DocumentType |
Guide
|
| Pages |
3
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM D 2240 : 2000 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 3167 : 2010 : R2017 | Standard Test Method for Floating Roller Peel Resistance of Adhesives |
| ASTM D 5420 : 1998 : REV A | Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact) |
| ASTM D 2583 : 2013 : REV A | Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor (Withdrawn 2022) |
| ASTM F 521 : 2022 | Standard Test Methods for Bond Integrity of Transparent Laminates |
| ASTM D 150 : 2022 | Standard Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation |
| ASTM F 734 : 2017 | Standard Test Method for Shear Strength of Fusion Bonded Polycarbonate Aerospace Glazing Material |
| ASTM D 1004 : 1994 : REV A | Standard Test Method for Initial Tear Resistance of Plastic Film and Sheeting |
| ASTM D 3167 : 1997 | Standard Test Method for Floating Roller Peel Resistance of Adhesives |
| ASTM D 1003 : 2007 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
| ASTM D 542 : 2014 | Standard Test Method for Index of Refraction of Transparent Organic Plastics |
| ASTM F 1252 : 1989 : R1996 | Standard Test Method for Measuring Optical Reflectivity of Transparent Materials |
| ASTM D 1499 : 2013 | Standard Practice for Filtered Open-Flame Carbon-Arc Exposures of Plastics |
| ASTM F 1181 : 2019 | Standard Test Method for Measuring Binocular Disparity in Transparent Parts |
| ASTM D 1003 : 2013 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
| ASTM F 320 : 2016 | Standard Test Method for Hail Impact Resistance of Aerospace Transparent Enclosures |
| ASTM G 154 : 2016 | Standard Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Nonmetallic Materials |
| ASTM D 1004 : 2013 | Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting |
| ASTM F 733 : 1990 : R1997 : EDT 1 | Standard Practice for Optical Distortion and Deviation of Transparent Parts Using the Double-Exposure Method |
| ASTM E 1640 : 2013 : R2018 | Standard Test Method for Assignment of the Glass Transition Temperature By Dynamic Mechanical Analysis |
| ASTM D 257 : 2014 | Standard Test Methods for DC Resistance or Conductance of Insulating Materials |
| ASTM F 1165 : 2020 | Standard Test Method for Measuring Angular Displacement of Multiple Images in Transparent Parts |
| ASTM D 2240 : 2004 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM F 735 : 2022 | Standard Test Method for Abrasion Resistance of Transparent Plastics and Coatings Using the Oscillating Sand Method |
| ASTM D 1499 : 2013 : R2021 | Standard Practice for Filtered Open-Flame Carbon-Arc Exposures of Plastics |
| ASTM E 2716 : 2009 | Standard Test Method for Determining Specific Heat Capacity by Sinusoidal Modulated Temperature Differential Scanning Calorimetry |
| ASTM D 543 : 2021 | Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents |
| ASTM D 412 : 2016 : EDT 1 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
| ASTM F 521 : 2016 | Standard Test Methods for Bond Integrity of Transparent Laminates |
| ASTM E 1269 : 1999 | Standard Test Method for Determining Specific Heat Capacity by Differential Scanning Calorimetry |
| ASTM G 154 : 2023 | Standard Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Materials |
| ASTM F 1252 : 2021 | Standard Test Method for Measuring Optical Reflectivity of Transparent Materials |
| ASTM F 1362 : 1997 | Standard Test Method for Shear Strength and Shear Modulus of Aerospace Glazing Interlayer Materials |
| ASTM F 1316 : 2018 | Standard Test Method for Measuring the Transmissivity of Transparent Parts |
| ASTM F 1252 : 2016 | Standard Test Method for Measuring Optical Reflectivity of Transparent Materials |
| ASTM D 1525 : 2017 | Standard Test Method for Vicat Softening Temperature of Plastics |
| ASTM F 520 : 2016 | Standard Test Method for Environmental Resistance of Aerospace Transparencies to Artificially Induced Exposures |
| ASTM F 734 : 2017 : R2022 | Standard Test Method for Shear Strength of Fusion Bonded Polycarbonate Aerospace Glazing Material |
| ASTM D 1044 : 2013 | Standard Test Method for Resistance of Transparent Plastics to Surface Abrasion |
| ASTM F 735 : 2017 | Standard Test Method for Abrasion Resistance of Transparent Plastics and Coatings Using the Oscillating Sand Method |
| ASTM E 2716 : 2009 : R2014 | Standard Test Method for Determining Specific Heat Capacity by Sinusoidal Modulated Temperature Differential Scanning Calorimetry |
| ASTM D 412 : 2016 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
| ASTM F 320 : 2021 | Standard Test Method for Hail Impact Resistance of Aerospace Transparent Enclosures |
| ASTM D 1525 : 1987 | Standard Test Method for Vicat Softening Temperature of Plastics |
| ASTM D 1003 : 2011 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
| ASTM E 1640 : 1999 | Standard Test Method for Assignment of the Glass Transition Temperature By Dynamic Mechanical Analysis |
| ASTM D 542 : 2022 | Standard Test Method for Index of Refraction of Transparent Organic Plastics |
| ASTM D 638 : 2014 | Standard Test Method for Tensile Properties of Plastics |
| ASTM D 1238 : 2004 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM F 801 : 2016 | Standard Test Method for Measuring Optical Angular Deviation of Transparent Parts |
| ASTM D 2240 : 2015 : R2021 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 2240 : 2002 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM E 2716 : 2023 | Standard Test Method for Determining Specific Heat Capacity by Modulated Temperature Differential Scanning Calorimetry |
| ASTM D 2584 : 1968 | Standard Method Of Test For Ignition Loss Of Cured Reinforced Resins |
| ASTM F 1165 : 1998 | Standard Test Method for Measuring Angular Displacement of Multiple Images in Transparent Parts |
| ASTM F 1316 : 1990 : R1996 | Standard Test Method for Measuring the Transmissivity of Transparent Parts |
| ASTM D 1003 : 2021 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
| ASTM F 1181 : 2009 : R2014 | Standard Test Method for Measuring Binocular Disparity in Transparent Parts |
| ASTM D 543 : 2020 | Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents |
| ASTM D 2565 : 1970 | Standard Recommended Practice For Operating Xenon Arc-Type (Water-Cooled) Light - And Water-Exposure Apparatus For Exposure Of Plastics |
| ASTM F 1181 : 1996 | Standard Test Method for Measuring Binocular Disparity in Transparent Parts |
| ASTM D 2240 : 2015 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM F 330 : 2016 | Standard Test Method for Bird Impact Testing of Aerospace Transparent Enclosures |
| ASTM F 330 : 2021 | Standard Test Method for Bird Impact Testing of Aerospace Transparent Enclosures |
| ASTM D 2584 : 2018 | Standard Test Method for Ignition Loss of Cured Reinforced Resins |
| ASTM D 2766 : 1995 | Standard Test Method for Specific Heat of Liquids and Solids |
| ASTM F 520 : 2021 | Standard Test Method for Environmental Resistance of Aerospace Transparencies to Artificially Induced Exposures |
| ASTM D 1499 : 1999 | Standard Practice Filtered Open-Flame Carbon-Arc Type Exposures of Plastics |
| ASTM D 570 : 2022 | Standard Test Method for Water Absorption of Plastics |
| ASTM D 2240 : 2015 : EDT 1 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 5420 : 2021 | Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact) |
| ASTM F 1362 : 2018 | Standard Test Method for Shear Strength and Shear Modulus of Aerospace Glazing Interlayer Materials |
| ASTM D 5420 : 2016 | Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact) |
| ASTM D 412 : 2016 : R2021 | Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension |
| ASTM D 150 : 2018 | Standard Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation |
| ASTM E 1269 : 2011 : R2018 | Standard Test Method for Determining Specific Heat Capacity by Differential Scanning Calorimetry |
| ASTM D 570 : 1998 : R2018 | Standard Test Method for Water Absorption of Plastics |
| ASTM D 1044 : 1999 | Standard Test Method for Resistance of Transparent Plastics to Surface Abrasion |
| ASTM F 801 : 2021 | Standard Test Method for Measuring Optical Angular Deviation of Transparent Parts |
| ASTM D 1044 : 2019 | Standard Test Method for Resistance of Transparent Plastics to Surface Abrasion by the Taber Abraser |
| ASTM D 1003 : 1992 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
| ASTM D 257 : 2014 : R2021 : EDT 1 | Standard Test Methods for DC Resistance or Conductance of Insulating Materials |
| ASTM F 1165 : 2015 | Standard Test Method for Measuring Angular Displacement of Multiple Images in Transparent Parts |
| ASTM D 1238 : 1985 | Standard Test Method for Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 1004 : 2021 | Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting |
| ASTM D 2583 : 1995 | Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor |
| ASTM D 638 : 2022 | Standard Test Method for Tensile Properties of Plastics |
£55.10
Excluding VAT
GBP
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.