ASTM F 880 : 2012 : R2017
Current
The latest, up-to-date edition.
Hardcopy , PDF
English
21-12-2017
CONTAINED IN VOL. 01.09, 2018 Specifies the requirements for austenitic grade stainless steel socket-set screws (SSS) sizes 0.060 through 1.000 in. square head set screws (SHSS) sizes 0.190 through 1.500 in., and slotted headless-set screws (HSS) 0.060 through 0.750 in., in two conditions, AF and CW.
1.1This specification covers the requirements for austenitic grade stainless steel socket-set screws (SSS) sizes 0.060 through 1.000 in. square head set screws (SHSS) sizes 0.190 through 1.500 in., and slotted headless set screws (HSS) 0.060 through 0.750 in., in two conditions, AF and CW.
1.2Units—The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
Note 1:A complete metric companion to Specification F880 has been developed—F880M; therefore, no metric equivalents are shown in this specification.
1.3The following hazards caveat pertains only to Test Method Section, Section 12 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Committee |
F 16
|
DocumentType |
Standard
|
Pages |
6
|
ProductNote |
Reconfirmed 2017
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
ASTM F 880M : 2016 | Standard Specification for Stainless Steel Socket Set Screws (Metric) (Withdrawn 2023) |
ASTM F 1718 : 2001 : R2019 | Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps |
ASTM D 3951 : 2010 | Standard Practice for Commercial Packaging |
ASTM F 1470 : 2012 | Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
ASTM A 555/A555M : 2020 | Standard Specification for General Requirements for Stainless Steel Wire and Wire Rods |
ASTM A 262 : 2015 : REDLINE | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels |
ASTM F 1470 : 2002 | Standard Guide for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
ASTM D 3951 : 1998 | Standard Practice for Commercial Packaging |
ASTM F 1470 : 2009 | Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
ASTM A 555/A555M : 2021 | Standard Specification for General Requirements for Stainless Steel Wire and Wire Rods |
ASTM E 18 : 2022 | Standard Test Methods for Rockwell Hardness of Metallic Materials |
ASTM A 342/A342M : 2014 | Standard Test Methods for Permeability of Weakly Magnetic Materials |
ASTM F 593 : 2017 : REDLINE | Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs |
ASTM A 262 : 2001 | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels |
ASTM E 18 : 2020 | Standard Test Methods for Rockwell Hardness of Metallic Materials |
ASTM D 3951 : 2015 | Standard Practice for Commercial Packaging |
ASTM A 380 : 2006 | Standard Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and Systems |
ASME B18.6.2 : 1998 | SLOTTED HEAD CAP SCREWS, SQAURE HEAD SET SCREWS, AND SLOTTED HEADLESS SET SCREWS (INCH SERIES) |
ASTM D 3951 : 2018 | Standard Practice for Commercial Packaging |
ASTM F 593 : 2022 | Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs |
ASTM A 555/A555M : 2022 | Standard Specification for General Requirements for Stainless Steel Wire and Wire Rods |
ASTM A 751 : 2021 | Standard Test Methods and Practices for Chemical Analysis of Steel Products |
ASTM F 788/F788M : 2020 : EDT 1 | Standard Specification for Surface Discontinuities of Bolts, Screws, Studs, and Rivets, Inch and Metric Series |
ASTM D 3951 : 2018 : R2023 | Standard Practice for Commercial Packaging |
ASTM A 555/A555M : 2023 | Standard Specification for General Requirements for Stainless Steel Wire and Wire Rods |
ASTM A 262 : 1998 | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels |
ASTM F 593 : 2017 | Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs |
ASTM F 788/F788M : 1997 | Standard Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series |
ASTM A 262 : 2015 | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels |
ASTM A 751 : 2020 | Standard Test Methods and Practices for Chemical Analysis of Steel Products |
ASTM E 18 : 2019 | Standard Test Methods for Rockwell Hardness of Metallic Materials |
ASTM F 1470 : 2018 | Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
ASME B18.3 : 2012 | SOCKET CAP, SHOULDER, SET SCREWS, AND HEX KEYS (INCH SERIES) |
ASTM F 1470 : 2001 | Standard Guide for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
ASTM F 1470 : 2019 | Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
ASTM F 1470 : 2024 | Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection |
ASTM A 342/A342M : 2014 : REDLINE | Standard Test Methods for Permeability of Weakly Magnetic Materials |
ASTM A 555/A555M : 2016 : REDLINE | Standard Specification for General Requirements for Stainless Steel Wire and Wire Rods |
ASTM A 342/A342M : 2021 | Standard Test Methods for Permeability of Weakly Magnetic Materials |
ASTM A 262 : 2015 : R2021 | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.