ASTM G 94 : 2005 : R2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Guide for Evaluating Metals for Oxygen Service
Hardcopy , PDF
07-07-2022
English
09-01-2014
CONTAINED IN VOL. 14.04, 2015 Pertains to metallic materials under consideration for oxygen or oxygen-enriched fluid service, direct or indirect.
1.1This guide applies to metallic materials under consideration for oxygen or oxygen-enriched fluid service, direct or indirect, as defined in Section 3. It is concerned primarily with the properties of a metallic material associated with its relative susceptibility to ignition and propagation of combustion. It does not involve mechanical properties, potential toxicity, outgassing, reactions between various materials in the system, functional reliability, or performance characteristics such as aging, shredding, or sloughing of particles, except when these might contribute to an ignition.
1.2This document applies only to metals; nonmetals are covered in Guide G63.
1.3The values stated in SI units are to be regarded as the standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| Committee |
G 04
|
| DocumentType |
Guide
|
| Pages |
31
|
| ProductNote |
Reconfirmed 2014
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM G 86 : 2017 | Standard Test Method for Determining Ignition Sensitivity of Materials to Mechanical Impact in Ambient Liquid Oxygen and Pressurized Liquid and Gaseous Oxygen Environments |
| ASTM G 114 : 2021 | Standard Practices for Evaluating the Age Resistance of Polymeric Materials Used in Oxygen Service |
| ASTM G 74 : 2013 : R2021 | Standard Test Method for Ignition Sensitivity of Nonmetallic Materials and Components by Gaseous Fluid Impact |
| ASTM G 88 : 2021 | Standard Guide for Designing Systems for Oxygen Service |
| ASTM G 124 : 2018 | Standard Test Method for Determining the Combustion Behavior of Metallic Materials in Oxygen-Enriched Atmospheres |
| ASTM G 126 : 2016 | Standard Terminology Relating to the Compatibility and Sensitivity of Materials in Oxygen Enriched Atmospheres |
| ASTM G 145 : 2008 : R2016 | Standard Guide for Studying Fire Incidents in Oxygen Systems |
| ASTM G 63 : 2015 | Standard Guide for Evaluating Nonmetallic Materials for Oxygen Service |
| ASTM G 121 : 2018 | Standard Practice for Preparation of Contaminated Test Coupons for the Evaluation of Cleaning Agents |
| ASTM F 1792 : 1997 : R2021 | Standard Specification for Special Requirements for Valves Used in Gaseous Oxygen Service |
| ASTM G 127 : 2015 | Standard Guide for the Selection of Cleaning Agents for Oxygen-Enriched Systems |
| ASTM G 125 : 2000 : R2015 | Standard Test Method for Measuring Liquid and Solid Material Fire Limits in Gaseous Oxidants |
| ASTM G 175 : 2013 : R2021 | Standard Test Method for Evaluating the Ignition Sensitivity and Fault Tolerance of Oxygen Pressure Regulators Used for Medical and Emergency Applications |
| ASTM G 128/G128M : 2015 | Standard Guide for Control of Hazards and Risks in Oxygen Enriched Systems |
| ASTM G 88 : 2013 : EDT 1 | Standard Guide for Designing Systems for Oxygen Service |
| ASTM D 4809 : 2000 | Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method) |
| ASTM D 2512 : 1995 | Standard Test Method for Compatibility of Materials with Liquid Oxygen (Impact Sensitivity Threshold and Pass-Fail Techniques) |
| ASTM D 4809 : 2018 | Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method) |
| ASTM D 4809 : 2013 | Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method) |
| ASTM D 2863 : 2008 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
| ASTM D 4809 : 2009 : REV A : EDT 1 | Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method) |
| ASTM G 88 : 2013 : REDLINE | Standard Guide for Designing Systems for Oxygen Service |
| ASTM G 88 : 2013 | Standard Guide for Designing Systems for Oxygen Service |
| ASTM D 4809 : 2000 : R2005 | Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method) |
| ASTM G 88 : 2021 | Standard Guide for Designing Systems for Oxygen Service |
| ASTM D 2863 : 2012 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
| CGA P 8.4 : 2013 | SAFE OPERATION OF REBOILERS/CONDENSERS IN AIR SEPARATION UNITS |
| ASTM D 2863 : 2000 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
| ASTM G 72 : 2001 | Standard Test Method for Autogenous Ignition Temperature of Liquids and Solids in a High-Pressure Oxygen-Enriched Environment |
| ASTM D 4809 : 1995 | Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method) |
| ASTM D 2863 : 2006 : REV A | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
| ASTM D 2863 : 2009 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
| ASTM D 2512 : 1995 : R2002 | Standard Test Method for Compatibility of Materials with Liquid Oxygen (Impact Sensitivity Threshold and Pass-Fail Techniques) |
| ASTM D 4809 : 2009 : REV A | Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method) |
| ASTM D 2863 : 1995 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-like Combustion of Plastics (Oxygen Index) |
| ASTM D 2863 : 2019 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
| CGA G 4.8 : 2013 | SAFE USE OF ALUMINUM-STRUCTURED PACKING FOR OXYGEN DISTILLATION |
| ASTM D 2863 : 2006 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
| ASTM D 4809 : 2009 | Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method) |
| ASTM D 2512 : 1995 : R2002 : EDT 1 | Standard Test Method for Compatibility of Materials with Liquid Oxygen (Impact Sensitivity Threshold and Pass-Fail Techniques) |
| ASTM G 128 : 1995 | Standard Guide for Control of Hazards and Risks in Oxygen Enriched Systems |
| ASTM D 4809 : 2006 | Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method) |
| ASTM G 128 : 2002 | Standard Guide for Control of Hazards and Risks in Oxygen Enriched Systems |
| ASTM D 2512 : 2017 | Standard Test Method for Compatibility of Materials with Liquid Oxygen (Impact Sensitivity Threshold and Pass-Fail Techniques) (Withdrawn 2023) |
| ASTM D 2863 : 2017 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
| ASTM D 2512 : 1995 : R2008 | Standard Test Method for Compatibility of Materials with Liquid Oxygen (Impact Sensitivity Threshold and Pass-Fail Techniques) (Withdrawn 2017) |
| ASTM G 86 : 1998 : REV A | Standard Test Method for Determining Ignition Sensitivity of Materials to Mechanical Impact in Ambient Liquid Oxygen and Pressurized Liquid and Gaseous Oxygen Environments |
| ASTM G 63 : 2015 : REDLINE | Standard Guide for Evaluating Nonmetallic Materials for Oxygen Service |
| ASTM D 2863 : 2017 : REV A | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
| CGA G 4.4 : 2012 | OXYGEN PIPELINE AND PIPING SYSTEMS |
| ASTM G 86 : 2017 | Standard Test Method for Determining Ignition Sensitivity of Materials to Mechanical Impact in Ambient Liquid Oxygen and Pressurized Liquid and Gaseous Oxygen Environments |
| ASTM D 2863 : 2010 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
| ASTM D 2863 : 2012 : EDT 1 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
| ASTM D 2863 : 2013 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
| ASTM G 126 : 2016 : REDLINE | Standard Terminology Relating to the Compatibility and Sensitivity of Materials in Oxygen Enriched Atmospheres |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.