We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • AWWA C541 : 2016

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    HYDRAULIC AND PNEUMATIC CYLINDER AND VANE-TYPE ACTUATORS FOR VALVES AND SLIDE GATES

    Available format(s):  Hardcopy, PDF

    Superseded date:  25-02-2022

    Language(s):  English

    Published date:  01-09-2016

    Publisher:  American Water Works Association

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    I Introduction
    II Special Issues
    III Use of This Standard
    IV Major Revisions
    V Comments
    Standard
    1 General
    2 References
    3 Definitions
    4 Requirements
    5 Verification
    6 Delivery
    Appendixes
    A Pneumatic or Hydraulic Actuator
      Data Form
    B Driver Media

    Abstract - (Show below) - (Hide below)

    Specifies hydraulic and pneumatic linear and quarter-turn actuators for operation of valves and slide gates in utility systems.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes AWWA C540. (11/2009)
    Document Type Standard
    Publisher American Water Works Association
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    AWWA C560:2014 CAST-IRON SLIDE GATES
    AWWA M49 : 2017 BUTTERFLY VALVES: TORQUE, HEAD LOSS, AND CAVITATION ANALYSIS
    AWWA C507 : 2015 BALL VALVES, 6 IN. THROUGH 60 IN. (150 MM THROUGH 1,500 MM)
    AWWA C563 : 2014 FABRICATED COMPOSITE SLIDE GATES
    AWWA C517 : 2016 RESILIENT-SEATED CAST-IRON ECCENTRIC PLUG VALVES
    AWWA C562 : 2014 FABRICATED ALUMINUM SLIDE GATES
    AWWA C504 : 2015 RUBBER-SEATED BUTTERFLY VALVES
    AWWA C516 : 2014 LARGE-DIAMETER RUBBER-SEATED BUTTERFLY VALVES, SIZES 78 IN. (2,000 MM) AND LARGER
    ANSI/AWWA C561 : 2014 FABRICATED STAINLESS-STEEL SLIDE GATES
    AWWA C520 : 2014 KNIFE GATE VALVES, SIZES 2 IN. (50 MM) THROUGH 96 IN. (2,400 MM)

    Standards Referencing This Book - (Show below) - (Hide below)

    NFPA T3.6.8 : 2010 FLUID POWER SYSTEMS - CYLINDERS - DIMENSIONS FOR ACCESSORIES FOR CATALOGED SQUARE HEAD INDUSTRIAL TYPES
    ASTM B 733 : 2015 : REDLINE Standard Specification for Autocatalytic (Electroless) Nickel-Phosphorus Coatings on Metal
    ASTM B 154 : 2016 : REDLINE Standard Test Method for Mercurous Nitrate Test for Copper Alloys
    ASTM A 395/A395M : 1999 Standard Specification for Ferritic Ductile Iron Pressure-Retaining Castings for Use at Elevated Temperatures
    ASTM A 689 : 1997 : R2002 Standard Specification for Carbon and Alloy Steel Bars for Springs
    SAE J 429 : 2014 MECHANICAL AND MATERIAL REQUIREMENTS FOR EXTERNALLY THREADED FASTENERS
    ASTM A 516/A516M : 2017 : REDLINE Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service
    ASTM B 240 : 2017 : REDLINE Standard Specification for Zinc and Zinc-Aluminum (ZA) Alloys in Ingot Form for Foundry and Die Castings
    ASTM A 449 : 2014 : REDLINE Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use
    ASTM A 276/A276M : 2017 : REDLINE Standard Specification for Stainless Steel Bars and Shapes
    ASTM D 570 : 1998 : R2018 Standard Test Method for Water Absorption of Plastics
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective