We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • BS 1042-1.4(1984) : 1984

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    MEASUREMENT OF FLUID FLOW IN CLOSED CONDUITS - GUIDE TO THE USE OF DEVICES SPECIFIED IN SECTIONS 1.1 AND 1.2

    Available format(s):  Hardcopy, PDF

    Superseded date:  31-03-1992

    Language(s):  English

    Published date:  01-01-1984

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Abstract - (Show below) - (Hide below)

    Gives sample calculations, physical data and other additional information for using pressure differential devices. Covers symbols, calculations, physical data and additional information on measurements and on pulsating and swirling flow.

    General Product Information - (Show below) - (Hide below)

    Committee PCL/2
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS 3156-5:1969 ANALYSIS OF FUEL GASES - TECHNIQUES FOR HIGH PRESSURE GASES
    BS 4773-1(1971) : 1971 METHODS FOR TESTING AND RATING AIR TERMINAL DEVICES FOR AIR DISTRIBUTION SYSTEMS - AERODYNAMIC TESTING
    BS 3554-2:1972 SPECIFICATION FOR GAS GOVERNORS - INDEPENDENT GOVERNORS FOR INLET PRESSURES UP TO 350 MBAR
    BS 848-1(1980) : 1980 FANS FOR GENERAL PURPOSES - METHODS OF TESTING PERFORMANCE
    BS 4979-1(1973) : AMD 1795
    BS 5384(1977) : LATEST GUIDE TO THE SELECTION AND USE OF CONTROL SYSTEMS FOR HEATING, VENTILATING AND AIR CONDITIONING INSTALLATIONS
    BS 1042-1.2(1989) : 1989 MEASUREMENT OF FLUID FLOW IN CLOSED CONDUITS - PRESSURE DIFFERENTIAL DEVICES - SPECIFICATION FOR SQUARE-EDGED ORIFICE PLATES AND NOZZLES AND OTHER ORIFICE PLATES
    BS 1042-1.2(1984) : LATEST SPEC. FOR SQUARE-EDGED ORIFICE PLATES, NOZZLES (WITH DRAIN HOLES, IN PIPES BELOW 50MM DIAMETER, AS INLET AND OUTLET DEVICES) AND OTHER ORIFICE PLATES AND BORDA INLETS
    BS 3135(1975) : LATEST SPECIFICATION FOR GAS TURBINES: ACCEPTANCE TESTS
    BS 5491(1977) : 1977 SPECIFICATION FOR RATING AND TESTING UNIT AIR CONDITIONERS OF ABOVE 7 KW COOLING CAPACITY
    BS 6540-1(1985) : 1985 AIR FILTERS USED IN AIR CONDITIONING AND GENERAL VENTILATION - METHODS OF TEST FOR ATMOSPHERIC DUST SPOT EFFICIENCY AND SYNTHETIC DUST WEIGHT ARRESTANCE
    BS 599(1966) : 1966 METHODS OF TESTING PUMPS
    BS 4485-2(1988) : 1988 WATER COOLING TOWERS - PART 2: METHODS FOR PERFORMANCE TESTING
    BS 3986(1991) : 1991 AMD 9836 METHODS OF TEST FOR DRYING PERFORMANCE OF AGRICULTURAL GRAIN DRYERS - GENERAL PROCEDURES AND LIMITED REQUIREMENTS FOR WHEAT
    BS 5968(1980) : 1980 METHODS OF ACCEPTANCE TESTING OF INDUSTRIAL TYPE STEAM TURBINES
    BS 6316(1983) : 1983 CODE OF PRACTICE FOR TEST PUMPING WATER WELLS
    BS 752(1974) : 1974 TEST CODE FOR ACCEPTANCE OF STEAM TURBINES
    BS 3986-1(1998) : 1998 METHODS OF TEST FOR DRYING PERFORMANCE OF AGRICULTURAL GRAIN DRYERS - GENERAL PROCEDURES AND LIMITED REQUIREMENTS FOR WHEAT

    Standards Referencing This Book - (Show below) - (Hide below)

    BS 1042-1.1(1981) : 1981 MEASUREMENT OF FLUID FLOW IN CLOSED CONDUITS - SPECIFICATION FOR SQUARE-EDGED ORIFICE PLATES, NOZZLES AND VENTURI TUBES INSERTED IN CIRCULAR CROSS SECTION CONDUITS RUNNING FULL
    ISO 2816:1973 Fundamental characteristics of a system of shoe sizing to be known as Mondopoint
    BS 1042-1.2(1984) : LATEST SPEC. FOR SQUARE-EDGED ORIFICE PLATES, NOZZLES (WITH DRAIN HOLES, IN PIPES BELOW 50MM DIAMETER, AS INLET AND OUTLET DEVICES) AND OTHER ORIFICE PLATES AND BORDA INLETS
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective