Specification for steel globe and globe stop and check valves (flanged and butt-welding ends) for the petroleum, petrochemical and allied industries

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

30-04-1975

Publisher

British Standards Institution

Co-operating organizations
Foreword
Section 1 - General
1 Scope
2 References
3 Nomenclature
4 Pressure classification
5 Pressure/temperature ratings
6 Nominal sizes
7 Information to be supplied by the purchaser
Section 2 - Design
8 Body
9 Bonnet
10 Disk, disk nut and disk thrust plate
11 Yoke
12 Handwheel
13 Stem and yoke bushes
14 Stuffing box, packing and lantern ring
15 Bolting
16 Operation
17 Bypass
18 Soft seal rings
Section 3 - Materials
19 Shell
20 Body seat rings
21 Bonnet gasket
22 Disk
23 Yoke
24 Disk thrust plate
25 Handwheel or chainwheel
26 Handwheel or chainwheel nut
27 Yoke bush
28 Yoke bush retaining nut
29 Gland
30 Trim
31 Lantern ring
32 Stem packing
33 Bolting
34 Plugs
35 Nameplate
36 Soft seals
37 Special applications
Section 4 - Marking
38 Required markings
39 Body and nameplate markings
40 Body and bonnet markings
41 Nameplate markings
42 Additional markings
43 Body dividing wall marking
44 Omission of markings
Section 5 - Testing
45 Production pressure testing
Section 6 - Shipping
46 Preliminary
47 Preparation for despatch
48 Packaging
Appendix A - Particular dimensions for each
class of valve
Appendix B - Application to piping systems
with BS 4504 flanges
Publications referred to

Straight, angle and (oblique) Y pattern with flanged or butt-welding ends in nominal sizes from 15 to 400 mm (½ to 16 in) and Class 150 to 2500.

This British Standard specifies requirements for cast or forged carbon and alloy steel outside screw and yoke globe and globe stop and check valves, straight pattern, angle pattern and (oblique) Y pattern, with flanged or butt-welding ends in nominal sizes within the range of 15 mm to 400 mm (½ in to 16 in) and Classes 150 to 2500. This standard can also be used as a general guide where valves of material composition outside the scope of section three of this standard are required as, for example, for use in highly corrosive services or environments or for low temperatures (see clause 37).

The standard can be adapted to apply to valves with needle type seats in 15 mm (½ in) an 20 mm (¾ in) nominal sizes which will meet all requirements of this standard, except that the valve seat bore is reduced and the needle point may be either integral with or loose on the stem.

Committee	PSE/18/2
DevelopmentNote	Supersedes 72/35873 DC and 89/79943 DC. (06/2004) Reviewed and confirmed by BSI, June 2007. (05/2007)
DocumentType	Standard
Pages	32
PublisherName	British Standards Institution
Status	Current
Supersedes	BS 1873:1960

NBR 15827 : 2014	INDUSTRIAL VALVES FOR INSTALLATIONS OF EXPLORATION, PRODUCTION, REFINING AND TRANSPORT OF PETROL PRODUCTS - REQUIREMENTS FOR DESIGN AND PROTOTYPE TEST
ISO 18139:2017	Ships and marine technology — Globe valves for use in low temperature applications — Design and testing requirements
BS 6364:1984	Specification for valves for cryogenic service
BS ISO 18139:2017	Ships and marine technology. Globe valves for use in low temperature applications. Design and testing requirements
BS 3351:1971	Specification for piping systems for petroleum refineries and petrochemical plants
BS 8010-3:1993	Code of practice for pipelines Pipelines subsea: design, construction and installation
BS 6683:1985	Guide to installation and use of valves
BS 8010-2.8:1992	Code of practice for pipelines. Pipelines on land: design, construction and installation Steel for oil and gas

BS 240:1986	Method for Brinell hardness test and for verification of Brinell hardness testing machines
BS 1600-2:1970	Specification for dimensions of steel pipe for the petroleum industry Metric units
BS 1133-6(1966) : 1966	PACKAGING CODE - TEMPORARY PROTECTION OF METAL SURFACES AGAINST CORROSION (DURING TRANSPORT AND STORAGE)
BS 3071:1986	Specification for nickel-copper alloy castings
BS 3351:1971	Specification for piping systems for petroleum refineries and petrochemical plants
BS 310:1972	Specification for blackheart malleable iron castings
BS 1769:1951	Specification. Unified black hexagon bolts, screws, nuts (UNC & UNF threads). Heavy series
BS 1560-2:1970	Circular flanges for pipes, valves and fittings (Class designated) Specification for steel pipe flanges (nominal sizes ½ in to 24 in). Metric dimensions
BS 2789:1985	Specification for spheroidal graphite or nodular graphite cast iron
BS 1832:1991	Specification for compressed asbestos fibre jointing
BS 2693-1:1956	Specification for screwed studs General purpose studs
BS 1501-6(1980) : LATEST
BS 1600:1991	Specification for dimensions of steel pipe for the petroleum industry
BS 1503:1989	Specification for steel forgings for pressure purposes
BS 3692:2001	ISO metric precision hexagon bolts, screws and nuts. Specification
BS 3076:1989	Specification for nickel and nickel alloys: bar
BS 6755-1:1986	Testing of valves Specification for production pressure testing requirements

View more information

£198.00

Excluding VAT

Product format

I agree to the DRM document license rules apply against the PDF selection made.

Please confirm that you agree to the document license rules for this document.

I agree to the document license rules .

Please confirm that you agree to the document license rules for this document.

Access your standards online with a subscription

Features

Simple online access to standards, technical information and regulations.
Critical updates of standards and customisable alerts and notifications.
Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

Get in touch with us

Log into your Account

BS 1873:1975

Current

Table of Contents

Abstract

Scope

General Product Information

Standards Referenced By This Book

Standards Referencing This Book

Category

Subcategory

Access your standards online with a subscription