We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • BS 2782-9.901A(1988) : 1988 AMD 14419

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    METHODS OF TESTING PLASTICS - SAMPLING AND TEST SPECIMEN PREPARATION - COMPRESSION MOULDING TEST SPECIMENS OF THERMOPLASTIC MATERIALS

    Available format(s): 

    Superseded date:  15-07-2003

    Language(s): 

    Published date:  23-11-2012

    Publisher:  British Standards Institution

    Add to Watchlist

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National foreword
    Method
    0 Introduction
    1 Scope and field of application
    2 References
    3 Definitions
    4 Apparatus
    5 Procedure
    6 Inspection of the moulded specimens or sheets
    7 Test report
    Table
       Cooling methods
    Figures
    1 Types of flash ("picture frame") moulds
    2 Positive-type mould

    Abstract - (Show below) - (Hide below)

    Gives the general principles and the procedures for thermoplastics in the preparation of compression moulded test specimens and sheets from which test specimens may be machined or stamped. Standardises the main steps of the procedure, with four different cooling methods to obtain mouldings in a reproducible state. Not suitable for reinforced thermo plastics. Illustrates types of flash ("picture frame") moulds and positive type mould.

    General Product Information - (Show below) - (Hide below)

    Committee PRM/21
    Development Note Renumbered and superseded by BS EN ISO 293 Supersedes 78/55602 DC (08/2003) Supersedes BS 2782-9.901A(1977). (10/2005)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS 2782-5.540B(1982) : 1982 METHODS OF TESTING PLASTICS - OPTICAL AND COLOUR PROPERTIES, WEATHERING - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES, (XENON ARC LAMP, ENCLOSED CARBON ARC LAMP, OPEN-FLAME CARBON ARC LAMP, FLUORESCENT TUBE LAMPS)
    BS 2782-9.940A(1990) : 1990 METHODS OF TESTING PLASTICS - SAMPLING AND TEST SPECIMEN PREPARATION - PREPARATION OF TEST SPECIMENS OF AMORPHOUS THERMOPLASTICS IN THE FORM OF BARS WITH A SPECIFIED REVERSION
    BS 2782-1.140A(1992) : 1992 METHODS OF TESTING PLASTICS - PART 1: THERMAL PROPERTIES - DETERMINATION OF THE BURNING BEHAVIOUR OF HORIZONTAL AND VERTICAL SPECIMENS IN CONTACT WITH A SMALL-FLAME IGNITION SOURCE
    BS 2782-11.1103D(1997) : 1997 METHODS OF TESTING PLASTICS - THERMOPLASTICS PIPES, FITTINGS AND VALVES - PLASTICS PIPING AND DUCTING SYSTEMS - POLYOLEFIN PIPES AND FITTINGS - DETERMINATION OF OXIDATION INDUCTION TIME
    BS 7825-3.10(1998) : 1998 CALIBRATION OF RUBBER AND PLASTICS TEST EQUIPMENT - CALIBRATION SCHEDULES - CONDITIONING, SAMPLE AND TEST PIECE PREPARATION
    BS 2782-3.370(1996) : 1996 METHODS OF TESTING PLASTICS - MECHANICAL PROPERTIES - DETERMINATION OF RESISTANCE TO WEAR BY ABRASIVE WHEELS
    BS 2782-0(1992) : 1992 METHODS OF TESTING PLASTICS - INTRODUCTION
    BS 2782-1.120A,B,D,E(1997) : 1997 METHODS OF TESTING PLASTICS - THERMAL PROPERTIES - PLASTICS - THERMOPLASTIC MATERIALS - DETERMINATION OF VICAT SOFTENING TEMPERATURE (VST)
    BS 2782-2.240A&B(1982) : LATEST METHODS OF TESTING PLASTICS - ELECTRICAL PROPERTIES - DETERMINATION OF LOSS TANGENT AND PERMITTIVITY AT POWER AND AUDIO FREQUENCIES
    BS 3412(1992) : 1992 METHODS OF SPECIFYING GENERAL PURPOSE POLYETHYLENE MATERIALS FOR MOULDING AND EXTRUSION
    02/123547 DC : DRAFT SEP 2002 BS 2782-0 - METHODS OF TESTING - PLASTICS - PART 0: INTRODUCTION
    BS 2782-3.336B(1978) : LATEST METHODS OF TESTING PLASTICS - MECHANICAL PROPERTIES - DETERMINATION OF DEFLECTION IN BEND UNDER AN APPLIED FORCE
    BS 903-C3(1982) : 1982 METHODS OF TESTING VULCANIZED RUBBER - DETERMINATION OF LOSS TANGENT AND PERMITTIVITY AT POWER AND AUDIO FREQUENCIES
    BS EN ISO 6252 : 1998 PLASTICS - DETERMINATION OF ENVIRONMENTAL STRESS CRACKING (ESC) - CONSTANT-TENSILE-STRESS METHOD
    BS EN ISO 877 : 1997
    BS EN ISO 179 : 1997 PLASTICS - DETERMINATION OF CHARPY IMPACT STRENGTH
    BS EN 728 : 1997 PLASTICS PIPING AND DUCTING SYSTEMS - POLYOLEFIN PIPES AND FITTINGS - DETERMINATION OF OXIDATION INDUCTION TIME
    BS EN ISO 4600 : 1998 PLASTICS - DETERMINATION OF ENVIRONMENTAL STRESS CRACKING (ESC) - BALL OR PIN IMPRESSION METHOD

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 468:1982 Surface roughness — Parameters, their values and general rules for specifying requirements
    ISO/R 286:1962 ISO system of limits and fits Part I : General, tolerances and deviations
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective