We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • BS 2782-9.902A(1992) : 1992 AMD 10344

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    METHODS OF TESTING PLASTICS - SAMPLING AND TEST SPECIMEN PREPARATION - PLASTICS - COMPRESSION MOULDING OF TEST SPECIMENS OF THERMOSETTING MATERIALS

    Available format(s): 

    Superseded date:  15-05-1999

    Language(s): 

    Published date:  23-11-2012

    Publisher:  British Standards Institution

    Add to Watchlist

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National foreword
    Committees responsible
    Method
    1 Scope
    2 Normative references
    3 Definitions
    4 Apparatus
    5 Material conditioning prior to moulding
    6 Moulding conditions
    7 Procedure
    8 Moulding report
    Figures
    1 Example of single-cavity positive mould
    2 Examples of moulds
    Tables
    1 Moulding conditions
    2 Information to be included in the moulding report

    Abstract - (Show below) - (Hide below)

    Gives the general principles and the procedures for the preparation of test specimens from thermosetting compounds moulded under heat and pressure and for the establishment of comparable test reports from different testing organizations. Only suitable for thermosetting materials based upon phenolics, aminoplastics, melamine phenolics, epoxides and unsaturated polyesters. Provides details of specimen preparation for test reports of the properties of such specimens. May often be necessary to prepare specimens by special methods because of their composition, their flow properties or other variable factors. In this case, an agreement shall be made between the interested parties. Tables giving the specimen properties shall refer to these specific methods. AMD 10344 RENUMBERS STD

    General Product Information - (Show below) - (Hide below)

    Committee PRM/21
    Development Note Renumbered and superseded by BS EN ISO 295. (03/2004)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS 2782-5.540B(1982) : 1982 METHODS OF TESTING PLASTICS - OPTICAL AND COLOUR PROPERTIES, WEATHERING - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES, (XENON ARC LAMP, ENCLOSED CARBON ARC LAMP, OPEN-FLAME CARBON ARC LAMP, FLUORESCENT TUBE LAMPS)
    BS 2782-3.322(1994) : 1994 AMD 8639 PLASTICS - DETERMINATION OF TENSILE PROPERTIES - TEST CONDITIONS FOR MOULDING AND EXTRUSION PLASTICS
    BS 771(1992) : 1992 SPECIFICATION FOR PHENOLIC MOULDING MATERIALS
    BS 2782-1.140A(1992) : 1992 METHODS OF TESTING PLASTICS - PART 1: THERMAL PROPERTIES - DETERMINATION OF THE BURNING BEHAVIOUR OF HORIZONTAL AND VERTICAL SPECIMENS IN CONTACT WITH A SMALL-FLAME IGNITION SOURCE
    BS 7825-3.10(1998) : 1998 CALIBRATION OF RUBBER AND PLASTICS TEST EQUIPMENT - CALIBRATION SCHEDULES - CONDITIONING, SAMPLE AND TEST PIECE PREPARATION
    BS 2782-3.370(1996) : 1996 METHODS OF TESTING PLASTICS - MECHANICAL PROPERTIES - DETERMINATION OF RESISTANCE TO WEAR BY ABRASIVE WHEELS
    BS 2782-0(1992) : 1992 METHODS OF TESTING PLASTICS - INTRODUCTION
    BS EN ISO 11248 : 2000 PLASTICS - THERMOSETTING MOULDING MATERIALS - EVALUATION OF SHORT-TERM PERFORMANCE AT ELEVATED TEMPERATURES
    BS EN ISO 179 : 1997 PLASTICS - DETERMINATION OF CHARPY IMPACT STRENGTH

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 3167:2014 Plastics Multipurpose test specimens
    ISO 2112:1990 Plastics Aminoplastic moulding materials Specification
    ISO 1183:1987 Plastics Methods for determining the density and relative density of non-cellular plastics
    ISO 468:1982 Surface roughness — Parameters, their values and general rules for specifying requirements
    ISO 4896:1990 Plastics Melamine/phenolic moulding materials Specification
    ISO 800:1992 Plastics Phenolic moulding materials Specification
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective