We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • BS 2782-9.930A(1996) : 1996 AMD 9487

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    METHODS OF TESTING PLASTICS - SAMPLING AND TEST SPECIMEN PREPARATION - PREPARATION BY MACHINING

    Available format(s): 

    Superseded date:  15-06-1997

    Language(s): 

    Published date:  23-11-2012

    Publisher:  British Standards Institution

    Add to Watchlist

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Committees responsible
    National foreword
    Introduction
    Method
    1 Scope
    2 Normative references
    3 Definitions
    4 Test specimens
    5 Machinery and tools
    6 Procedure
    7 Test report
    Annex
    A (informative) Bibliography
    Table
    1 Recommended machining conditions for four types of test
       specimen and for notches
    Figures
    1 Geometry of the active part of cutting tools
    2 Shape of milling chips
    3 Chip thickness ds in the range between 0,003 mm and 0,07 mm
       versus rotational speed n and feed speed vf of a milling
       machine (R = 40 mm)
    4 Example of a circular cutter (half-section of a diamond-
       edged cutter)

    Abstract - (Show below) - (Hide below)

    Gives general principles and procedures to be followed when machining and notching test specimens from compression-moulded and injection-moulded plastics, extruded sheets, plates and partially or wholly-finished products. AMD 9487 RENUMBERS THIS STANDARD

    General Product Information - (Show below) - (Hide below)

    Committee PRI/21
    Development Note Renumbered and superseded by BS EN ISO 2818. Supersedes BS 2782-9.930A(1977) and 90/48432 DC. (10/2005)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS 2782-5.540B(1982) : 1982 METHODS OF TESTING PLASTICS - OPTICAL AND COLOUR PROPERTIES, WEATHERING - METHODS OF EXPOSURE TO LABORATORY LIGHT SOURCES, (XENON ARC LAMP, ENCLOSED CARBON ARC LAMP, OPEN-FLAME CARBON ARC LAMP, FLUORESCENT TUBE LAMPS)
    BS 2782-3.322(1994) : 1994 AMD 8639 PLASTICS - DETERMINATION OF TENSILE PROPERTIES - TEST CONDITIONS FOR MOULDING AND EXTRUSION PLASTICS
    BS 2782-3.370(1996) : 1996 METHODS OF TESTING PLASTICS - MECHANICAL PROPERTIES - DETERMINATION OF RESISTANCE TO WEAR BY ABRASIVE WHEELS
    04/30115932 DC : DRAFT NOV 2004 BS PL 7 - UNSATURATED POLYESTER RESINS FOR LOW PRESSURE LAMINATING OF GLASS FIBRE - REINFORCED LAMINATES - TEST METHOD
    BS 2782-1.120A,B,D,E(1997) : 1997 METHODS OF TESTING PLASTICS - THERMAL PROPERTIES - PLASTICS - THERMOPLASTIC MATERIALS - DETERMINATION OF VICAT SOFTENING TEMPERATURE (VST)
    04/30115928 DC : DRAFT NOV 2004 BS PL 5 - UNSATURATED POLYESTER RESINS FOR LOW PRESSURE LAMINATING OF HIGH STRENGTH FIBRE - REINFORCED COMPOSITES - TEST METHOD
    BS PL5(2005) : 2005 AEROSPACE SERIES - UNSATURATED POLYESTER RESINS FOR LOW PRESSURE LAMINATING OF HIGH STRENGTH FIBRE REINFORCED COMPOSITES - TEST METHODS
    BS PL7(2005) : 2005 AEROSPACE SERIES - UNSATURATED POLYESTER RESINS FOR LOW PRESSURE LAMINATING OF GLASS FIBRE REINFORCED LAMINATES - TEST METHODS
    BS EN ISO 4599 : 1997 PLASTICS - DETERMINATION OF RESISTANCE TO ENVIRONMENTAL STRESS CRACKING (ESC) - BENT STRIP METHOD
    BS EN ISO 877 : 1997
    BS EN ISO 179 : 1997 PLASTICS - DETERMINATION OF CHARPY IMPACT STRENGTH

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 6106:2013 Abrasive products Checking the grain size of superabrasives
    ISO 3017:1981 Abrasive discs Designation, dimensions and tolerances Selection of disc outside diameter/centre hole diameter combinations
    ISO 6104:2005 Superabrasive products Rotating grinding tools with diamond or cubic boron nitride General survey, designation and multilingual nomenclature
    ISO 6168:1980 Abrasive products Diamond or cubic boron nitride grinding wheels Dimensions
    ISO 3855:1977 Milling cutters Nomenclature
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective