BS 3HR 100:1978
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Procedure for inspection and testing of wrought heat-resisting alloys
Available format(s)
Hardcopy , PDF
Superseded date
31-01-2010
Language(s)
English
Published date
31-10-1978
Publisher
Foreword
Section one. General requirements
Section two. Bars for machining and sections
Section three. Forging stock and billets and bars for
subsequent working
Section four. Forgings
Section five. Plate, sheet and strip
Section six. Tubes
Section seven. Wire
Section eight. Parts finally heat treated after
machining
Section nine. Bar and wire intended for the manufacture
of fasteners
Appendices
A. Phase composition control
B. Notes on table 10
TABLES
1. Tolerance on diameters of drawn and ground bars
2. Tolerance on widths across flats of bright drawn
bars
3. Tolerances on diameters of machined round bars
4. Tolerances on thicknesses of cold rolled plate and
sheet
5. Tolerances on thicknesses of hot rolled plate and
sheet
6. Tolerances on thicknesses of cold rolled strip
7. Tolerances on widths and lengths of cold rolled
plate and sheet
8. Tolerances on widths and lengths of hot rolled
plated and sheet
9. Tolerances on widths of cold rolled strip
10. Tolerances on dimensions of cold worked tubes
11. Tolerances on diameters of wire
12. Alloy composition levels of nickel, iron and cobalt
base alloys
13. Relative atomic masses of elements
Describes inspection and testing requirements for wrought heat-resisting alloys used for aerospace purposes. The procedure is for use in conjunction with related material specifications in the 'HR' series of British Standards and in the Ministry of Defence D.T.D. series.
| Committee |
ACE/61
|
| DevelopmentNote |
Supersedes 76/71732 DC, 92/77473 DC and 95/714494 DC. (08/2004)
|
| DocumentType |
Standard
|
| Pages |
46
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| BS 3HR1(2010) : 2010 | SPECIFICATION FOR NICKEL-CHROMIUM-TITANIUM-ALUMINIUM HEAT-RESISTING ALLOY BILLETS, BARS, FORGINGS AND PARTS (NICKEL BASE, CR 19.5, TI 2.2, AL 1.4) |
| BS HR 505:1981 | Specification for nickel-chromium-iron-titanium-niobium-aluminium heat-resisting alloy round wire for thread inserts (maximum diameter 2 mm) (nickel base, Cr 15.5, Fe 7.0, Ti 2.5, Nb/Ta 0.95, Al 0.70) |
| 09/30201781 DC : 0 | BS 2HR 53 - SPECIFICATION FOR NICKEL-IRON-CHROMIUM-MOLYBDENUM-TITANIUM HEAT-RESISTING ALLOY BILLETS, BARS, FORGINGS AND PARTS (NI/CO 42.5, CR 12.5, MO 5.8, TI 3.0, FE REMAINDER) |
| 09/30201215 DC : DRAFT MAY 2009 | BS 2HR 207 - SPECIFICATION FOR NICKEL-IRON-CHROMIUM-MOLYBDENUM-ALUMINIUM-TITANIUM HEAT-RESISTING ALLOY PLATE, SHEET AND STRIP (NI/CO 43.5, CR 16.5, MO 3.3, AL 1.2, TI 1.2, FE REMAINDER) |
| DEFSTAN 95-7/2(2004) : 2004 | WIRE FOR LOCKING PURPOSES AND WIRE LOCKING PRACTICE FOR AEROSPACE USE |
| BS 2HR 205:2009 | Specification for nickel-copper alloy sheet and strip: annealed (nickel base, Cu 31) |
| 09/30199922 DC : 0 | BS 3HR 1 - SPECIFICATION FOR NICKEL-CHROMIUM-TITANIUM-ALUMINIUM HEAT-RESISTING ALLOY BILLETS, BARS, FORGINGS AND PARTS (NICKEL BASE, CR 19.5, TI 2.2, AL 1.4) |
| BS 2HR 206:2009 | Specification for nickel-cobalt-chromium-molybdenum-titanium-aluminium heat-resisting alloy plate, sheet and strip (nickel base, Co 20, Cr 20, Mo 5.9, Ti 2.1, Al 0.5) |
| 09/30199924 DC : 0 | BS 3HR 2 - SPECIFICATION FOR NICKEL-CHROMIUM-COBALT-TITANIUM-ALUMINIUM HEAT-RESISTING ALLOY BILLETS, BARS, FORGINGS AND PARTS (NICKEL BASE, CR 19.5, CO 18.0, TI 2.5, AL 1.5) |
| BS 2HR 203:2009 | Specification for nickel-chromium-titanium heat-resisting alloy plate, sheet and strip (nickel base, Cr 19.5, Ti 0.4) |
| 09/30201218 DC : DRAFT MAY 2009 | BS 2HR 208 - SPECIFICATION FOR NICKEL-CHROMIUM-IRON ALLOY PLATE, SHEET AND STRIP: ANNEALED (NICKEL BASE, CR 15.5, FE 8) |
| 09/30199937 DC : 0 | BS 2HR 10 - SPECIFICATION FOR NICKEL-COBALT-CHROMIUM-MOLYBDENUM-TITANIUM-ALUMINIUM HEAT-RESISTING ALLOY BILLETS, BARS, FORGINGS AND PARTS (NICKEL BASE, CO 20, CR 20, MO 5.9, TI 2.1, AL 0.5) |
| BS HR 209:1989 | Specification for nickel-chromium-cobalt-molybdenum-titanium-aluminium heat-resisting alloy sheet, strip and plate: softened (nickel base, Cr 18, Co 14, Mo 7, Ti 2.2, Al 2.1) |
| BS 2HR 10:2010 | Specification for nickel-cobalt-chromium-molybdenum-titanium-aluminium heat-resisting alloy billets, bars, forgings and parts (nickel base, Co 20, Cr 20, Mo 5.9, Ti 2.1, Al 0.5) |
| BS 2HR 4:2010 | Specification for nickel-chromium-cobalt-aluminium-molybdenum-titanium heat-resisting alloy billets, bars, forgings and parts (nickel base, Cr 15, Co 14.2, Al 5, Mo 4, Ti 4) |
| BS 2HR 51:2010 | Specification for high expansion heat-resisting steel billets, bars, forgings and parts (Ni 25.5, Cr 15, Ti 2, Mn 1.5, Mo 1.25, Si 0.7, V 0.3) (Solution treated at 980 °C) |
| 09/30199933 DC : 0 | BS 2HR 5 - SPECIFICATION FOR NICKEL-CHROMIUM-TITANIUM HEAT-RESISTING ALLOY BILLETS, BARS, FORGINGS AND PARTS (NICKEL BASE, CR 19.5, TI 0.4) |
| BS 2HR 40:2010 | Specification for cobalt-chromium-tungsten-nickel-manganese heat-resisting alloy billets, bars and forgings (cobalt base Cr 20, W 15, Ni 10, Mn 1.5) |
| 09/30201208 DC : DRAFT MAY 2009 | BS 2HR 204 - SPECIFICATION FOR NICKEL-CHROMIUM-IRON-MOLYBDENUM-COBALT-TUNGSTEN HEAT-RESISTING ALLOY SHEET AND STRIP (NICKEL BASE, CR 21.7, FE 18.5, MO 9, CO 1.5, W 0.6) |
| BS 2HR 505:2010 | Specification for nickel-chromium-iron-titanium-niobium-aluminium heat-resisting alloy round wire with a maximum diameter of 2 mm for thread inserts (nickel base Cr 15.5, Fe 7.0, Ti 2.5, Nb/Ta 0.95, Al 0.70) |
| 09/30201787 DC : 0 | BS 2HR 55 - SPECIFICATION FOR NICKEL-IRON-CHROMIUM-MOLYBDENUM-ALUMINIUM-TITANIUM HEAT-RESISTING ALLOY BILLETS, BARS, FORGINGS AND PARTS (NI/CO 43.5, CR 16.5, MO 3.3, AL 1.2, TI 1.2, FE REMAINDER) |
| 09/30199929 DC : 0 | BS 2HR 3 - SPECIFICATION FOR NICKEL-COBALT-CHROMIUM-MOLYBDENUM-ALUMINIUM-TITANIUM HEAT-RESISTING ALLOY BILLETS, BARS, FORGINGS AND PARTS (NICKEL BASE, CO 20, CR 14.8, MO 5, AL 4.8, TI 1.2) |
| BS 3HR 201:2009 | Specification for nickel-chromium- titanium-aluminium heat-resisting alloy plate, sheet and strip (nickel base, Cr 19.5, Ti 2.2, Al 1.4) |
| BS 2HR 204:2009 | Specification for nickel-chromium-iron-molybdenum-cobalt-tungsten heat-resisting alloy plate, sheet and strip (nickel base, Cr 21.7, Fe 18.5, Mo 9, Co 1.5, W 0.6) |
| BS HR 4:1972 | Specification for nickel-chromium-cobalt-aluminium-molybdenum-titanium heat-resisting alloy billets, bars, forgings and parts (nickel base, Cr 15, Co 14.2, Al 5, Mo 4, Ti 4) |
| 09/30201774 DC : 0 | BS 2HR 51 - SPECIFICATION FOR HIGH EXPANSION HEAT-RESISTING STEEL BILLETS, BARS, FORGINGS AND PARTS (NI 25.5, CR 15, TI 2, MN 1.5, MO 1.25, SI 0.7, V 0.3) (SOLUTION TREATED AT 980 DEGREE C) |
| BS 2HR 208:2009 | Specification for nickel-chromium-iron alloy plate, sheet and strip: annealed (nickel base, Cr 15.5, Fe 8) |
| BS 4HR 601:2010 | Specification for nickel-chromium-titanium-aluminium heat-resisting alloy bar and wire (maximum diameter or minor sectional dimension of 30 mm) for the manufacture of fasteners (nickel base, Cr 19.5, Ti 2.2, Al 1.4) |
| 09/30201771 DC : 0 | BS 2HR 40 - SPECIFICATION FOR COBALT-CHROMIUM-TUNGSTEN-NICKEL-MANGANESE HEAT-RESISTING ALLOY BILLETS, BARS AND FORGINGS (COBALT BASE CR 20, W 15, NI 10, MN 1.5) |
| BS 3HR 202:2009 | Specification for nickel-chromium-cobalt-titanium-aluminium heat-resisting alloy sheet and strip (nickel base, Cr 19.5, Co 18.0, Ti 2.5, Al 1.5) |
| 09/30201200 DC : DRAFT MAY 2009 | BS 3HR 201 - SPECIFICATION FOR NICKEL-CHROMIUM-TITANIUM-ALUMINIUM HEAT-RESISTING ALLOY PLATE, SHEET AND STRIP (NICKEL BASE, CR 19.5, TI 2.2, AL 1.4) |
| BS HR 53:1973 | Specification for nickel-iron-chromium-molybdenum-titanium heat-resisting alloy billets, bars, forgings and parts (Ni/Co 42.5, Cr 12.5, Mo 5.8, Ti 3.0, Fe remainder) |
| BS HR 55:1980 | Specification for nickel-iron-chromium-molybdenum-aluminium-titanium heat-resisting alloy billets, bars, forgings and parts (Ni/Co 43.5, Cr 16.5, Mo 3.3, Al 1.2, Ti 1.2, Fe remainder) |
| BS 2HR 52:2010 | Specification for heat-resisting steel billets, bars, forgings and parts (Ni 25.5, Cr 14.7, Ti 1.8, Mn 1.5, Mo 1.2, V 0.3) |
| BS 3HR 601:1989 | Specification for nickel-chromium-titanium-aluminium heat-resisting alloy bar and wire for the manufacture of fasteners (maximum diameter or minor sectional dimension 30 mm) (nickel base Cr 19.5, Ti 2.2, Al 1.4) |
| BS 2HR 55:2010 | Specification for nickel-iron-chromium-molybdenum-aluminium-titanium heat-resisting alloy billets, bars, forgings and parts (Ni/Co 43.5, Cr 16.5, Mo 3.3, Al 1.2, Ti 1.2, Fe remainder) |
| 09/30201778 DC : 0 | BS 2HR 52 - SPECIFICATION FOR HEAT-RESISTING STEEL BILLETS, BARS, FORGINGS AND PARTS (NI 25.5, CR 14.7, TI 1.8, MN 1.5, MO 1.2, V 0.3) |
| BS 2HR 5:2010 | Specification for nickel-chromium-titanium heat-resisting alloy billets, bars, forgings and parts (nickel base, Cr 19.5, Ti 0.4) |
| BS 2HR 6:2010 | Specification for nickel-chromium- iron-molybdenum-cobalt-tungsten heat-resisting alloy billets, bars, forgings and parts (nickel base, Cr 21.7, Fe 18.5, Mo 9, Co 1.5, W 0.6) |
| 09/30201210 DC : DRAFT MAY 2009 | BS 2HR 205 - SPECIFICATION FOR NICKEL-COPPER ALLOY SHEET AND STRIP: ANNEALED (NICKEL BASE, CU 31) |
| BS 2HR 207:2009 | Specification for nickel-iron-chromium-molybdenum-aluminium-titanium heat-resisting alloy plate, sheet and strip (Ni/Co 43.5, Cr 16.5, Mo 3.3, Al 1.2, Ti 1.2, Fe remainder) |
| 09/30201213 DC : DRAFT MAY 2009 | BS 2HR 206 - SPECIFICATION FOR NICKEL-COBALT-CHROMIUM-MOLYBDENUM-TITANIUM-ALUMINIUM HEAT-RESISTING ALLOY PLATE, SHEET AND STRIP (NICKEL BASE, CO 20, CR 20, MO 5.9, TI 2.1, AL 0.5) |
| 09/30201203 DC : DRAFT MAY 2009 | BS 3HR 202 - SPECIFICATION FOR NICKEL-CHROMIUM-COBALT-TITANIUM-ALUMINIUM HEAT-RESISTING ALLOY SHEET AND STRIP (NICKEL BASE, CR 19.5, CO 18.0, TI 2.5, AL 1.5) |
| 09/30199931 DC : 0 | BS 2HR 4 - SPECIFICATION FOR NICKEL-CHROMIUM-COBALT-ALUMINIUM-MOLYBDENUM-TITANIUM HEAT-RESISTING ALLOY BILLETS, BARS, FORGINGS AND PARTS (NICKEL BASE, CO 15, CR 14.2, AL 5, MO 4, TI 4) |
| 09/30199935 DC : 0 | BS 2HR 6 - SPECIFICATION FOR NICKEL-CHROMIUM-IRON-MOLYBDENUM-COBALT-TUNGSTEN HEAT-RESISTING ALLOY BILLETS, BARS, FORGINGS AND PARTS (NICKEL BASE, CR 21.7, F E 18.5, MO 9, CO 1.5, W 0.6) |
| BS 2HR 3:2010 | Specification for nickel-cobalt-chromium-molybdenum-aluminium-titanium heat-resisting alloy billets, bars, forgings and parts (nickel base, Co 20, Cr 14.8, Mo 5, Al 4.8, Ti 1.2) |
| 09/30201205 DC : DRAFT MAY 2009 | BS 2HR 203 - SPECIFICATION FOR NICKEL-CHROMIUM-TITANIUM HEAT-RESISTING ALLOY PLATE, SHEET AND STRIP (NICKEL BASE, CR 19.5, TI 0.4) |
| BS HR 208:1989 | Specification for nickel-chromium-iron alloy sheet, strip and plate: annealed (Nickel base, Cr 15.5, Fe 8) |
| BS 2HR 506:2010 | Specification for nickel-chromium-cobalt-titanium-aluminium heat-resisting alloy wire: softened (nickel base, Cr 19.5, Co 1.8, Ti 2.5, Al 1.5) |
| BS 2HR 53:2010 | Specification for nickel-iron-chromium-molybdenum-titanium heat-resisting alloy billets, bars, forgings and parts (Ni/Co 42.5, Cr 12.5, Mo 5.8, Ti 3.0, Fe remainder) |
| BS HR 506:1989 | Nickel-chromium-cobalt-titanium-aluminium heat-resisting alloy wire: softened (nickel base, Cr 19.5, Co 18, Ti 2.5, Al 1.5) |
| BS M 36:1970 | Method for ultrasonic testing of special forgings by an immersion technique using flat-bottomed holes as a reference standard |
| BS 3923-3:1972 | Methods for ultrasonic examination of welds Manual examination of nozzle welds |
| BS 4175-2:1970 | Method for Rockwell superficial hardness test (N and T scales) Verification of the testing machine |
| BS 4175-1:1967 | Method for Rockwell superficial hardness test (N and T scales) Testing of metals |
| BS M46(1974) : LATEST | |
| BS 891-1:1962 | Method for Rockwell hardness test Testing of metals |
| BS DD44(1974) : LATEST | METHODS FOR THE DETERMINATION OF GRAIN SIZE OF NON-FERROUS ALLOYS |
| BS 891-2:1964 | Method for Rockwell hardness test Verification of the testing machine |
| BS 427-2:1962 | Method for Vickers hardness test Verification of the testing machine |
| BS 427-1:1961 | Method for Vickers hardness test Testing of metals |
| BS 4A 4:1966 | Test pieces and test methods for metallic materials for aircraft. Metric units |
| BS 240-2:1964 | Method for Brinell hardness test Verification of the testing machine |
£262.00
Excluding VAT
GBP
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.