|
BS EN 1978:1998
|
Copper and copper alloys. Copper cathodes
|
|
BS EN 12878:2014
|
Pigments for the colouring of building materials based on cement and/or lime. Specifications and methods of test
|
|
BS 2782-3:Methods 320A to 320F:1976
|
Methods of testing plastics. Mechanical properties Tensile strength, elongation and elastic modulus
|
|
BS EN 1676:2010
|
Aluminium and aluminium alloys. Alloyed ingots for remelting. Specifications
|
|
BS 2782-5.550B(1996) : 1996 AMD 9494
|
|
|
BS EN 10048:1997
|
Hot rolled narrow steel strip. Tolerances on dimensions and shape
|
|
BS EN ISO 877:1997
|
Plastics. Methods of exposure to direct weathering, to weathering using glass-filtered daylight, and to intensified weathering by daylight using Fresnel mirrors.
|
|
BS EN ISO 9445-2:2010
|
Continuously cold-rolled stainless steel. Tolerances on dimensions and form Wide strip and plate/sheet
|
|
BS EN 197-4:2004
|
Cement Composition, specifications and conformity criteria for low early strength blastfurnace cements
|
|
BS 6610:1996
|
Specification for Pozzolanic pulverized-fuel ash cement
|
|
BS EN 10095:1999
|
Heat resisting steels and nickel alloys
|
|
BS EN 12620:2013
|
Aggregates for concrete
|
|
ISO 1461:2009
|
Hot dip galvanized coatings on fabricated iron and steel articles — Specifications and test methods
|
|
BS EN 10051:2010
|
Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels. Tolerances on dimensions and shape
|
|
BS EN 197-1:2011
|
Cement Composition, specifications and conformity criteria for common cements
|
|
BS EN 10130:2006
|
Cold rolled low carbon steel flat products for cold forming. Technical delivery conditions
|
|
BS EN ISO 1461:2009
|
Hot dip galvanized coatings on fabricated iron and steel articles. Specifications and test methods
|
|
BS EN 1559-4:2015
|
Founding. Technical conditions of delivery Additional requirements for aluminium alloy castings
|
|
BS 6954-2:1988
|
Tolerances for building Recommendations for statistical basis for predicting fit between components having a normal distribution of sizes
|
|
ISO 9445-2:2009
|
Continuously cold-rolled stainless steel Tolerances on dimensions and form Part 2: Wide strip and plate/sheet
|
|
BS EN 10346:2015
|
Continuously hot-dip coated steel flat products for cold forming. Technical delivery conditions
|
|
BS EN 13279-1:2008
|
Gypsum binders and gypsum plasters Definitions and requirements
|
|
BS EN 10029:2010
|
Hot-rolled steel plates 3 mm thick or above. Tolerances on dimensions and shape
|
|
BS EN 1706:2010
|
Aluminium and aluminium alloys. Castings. Chemical composition and mechanical properties
|
|
BS 1191-1:1973
|
Specification for gypsum building plasters Excluding premixed lightweight plasters
|
|
BS EN ISO 9445-1:2010
|
Continuously cold-rolled stainless steel. Tolerances on dimensions and form Narrow strip and cut lengths
|
|
ISO 9445-1:2009
|
Continuously cold-rolled stainless steel Tolerances on dimensions and form Part 1: Narrow strip and cut lengths
|
|
BS EN 1976:2012
|
Copper and copper alloys. Cast unwrought copper products
|
|
BS 4027:1996
|
Specification for sulfate-resisting Portland cement
|
|
BS 6954-1:1988
|
Tolerances for building Recommendations for basic principles for evaluation and specification
|
|
BS EN 1559-1:2011
|
Founding. Technical conditions of delivery General
|
|
BS 6954-3:1988
|
Tolerances for building Recommendations for selecting target size and predicting fit
|
|
BS 6750:1986
|
Specification for modular coordination in building
|
Important note : All end users must be registered with an Account prior to user licenses being assigned.