BS 7158:2001

Superseded

View Superseded by

Plastics inspection chambers for drains and sewers. Specification

Available format(s)

Hardcopy , PDF

Superseded date

18-12-2003

Language(s)

English

Published date

15-08-2001

Publisher

British Standards Institution

Committees responsible
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Materials
5 Dimensions
6 Appearance
7 Performance requirements
8 Marking
Annex A (normative) Methods of test for watertightness
Annex B (normative) Method of test for resistance to
        angular deflection
Annex C (normative) Method of test for resistance to
        diametric distortion of chamber joint assemblies
        with flexible pipe system
Annex D (normative) Method of test for shear resistance of
        chamber joint assemblies with rigid pipe system
Annex E (normative) Method of test for resistance to
        elevated temperature cycling
Annex F (normative) Method of test for the determination
        of specific tangential initial stiffness
Annex G (normative) Method of test for resistance to
        vertical loading
Annex H (informative) Guidance on use of inspection chambers
        relative to surface load and installation procedures
Annex I (normative) Method of test for resistance to
        negative pressure
Annex J (informative) Guidance on quality control testing
Bibliography

Specifies requirements for plastics inspection chambers for use at depths to invert not exceeding 6 m in the construction of drainage and sewerage systems. It is applicable to non-man-entry chambers with or without raising pieces and having a nominal cross-section.

Committee	PRI/88/1
DevelopmentNote	Supersedes BS 7158(1989) (07/2001) Supersedes 99/121878 DC. (01/2004) Reviewed and confirmed by BSI, June 2007. (05/2007)
DocumentType	Standard
Pages	26
PublisherName	British Standards Institution
Status	Superseded
SupersededBy	BS EN 13598-1:2010 BS EN 13598-2:2009
Supersedes	BS 7158:1989

BS EN 1610:2015	Construction and testing of drains and sewers
PREN 13598-1 : DRAFT 2010	PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 1: SPECIFICATIONS FOR ANCILLARY FITTINGS INCLUDING SHALLOW INSPECTION CHAMBERS
BS EN 752-7:1998	Drain and sewer systems outside buildings Maintenance and operations
BS 7903:1997	Guide to selection and use of gully tops and manhole covers for installation within the highway
BS EN 752-6:1998	Drain and sewer systems outside buildings Pumping installations
BS 3496:1989	Specification for E glass fibre chopped strand mat for reinforcement of polyester and other liquid laminating systems
BS EN 752-2:1997	Drain and sewer systems outside buildings Performance requirements
BS EN 1295-1 : 1998	STRUCTURAL DESIGN OF BURIED PIPELINES UNDER VARIOUS CONDITIONS OF LOADING - PART 1: GENERAL REQUIREMENTS
BS EN 681-1:1996	Elastomeric seals. Material requirements for pipe joint seals used in water and drainage applications Vulcanized rubber
BS 6209:1982	Specification for solvent cement for non-pressure thermoplastics pipe systems
BS EN 295-1:2013	Vitrified clay pipe systems for drains and sewers Requirements for pipes, fittings and joints
BS EN 681-3:2000	Elastomeric seals. Materials requirements for pipe joint seals used in water and drainage applications Cellular materials of vulcanized rubber
BS 5955-6:1980	Plastics pipework (thermoplastics materials) Code of practice for the installation of unplasticized PVC pipework for gravity drains and sewers
BS EN 752-5:1998	Drain and sewer systems outside buildings Rehabilitation
BS 2782-11.1103V(1995) : 1995	METHODS OF TESTING PLASTICS - THERMOPLASTICS PIPES, FITTINGS AND VALVES - PLASTICS PIPING AND DUCTING SYSTEMS - THERMOPLASTICS PIPES AND FITTINGS - DETERMINATION OF VICAT SOFTENING TEMPERATURE
DIN 1259-1:2001-09	GLASS - PART 1: TERMINOLOGY FOR GLASS TYPES AND GROUPS
BS 8301:1985	Code of practice for building drainage
BS 4346-1:1969	Joints and fittings for use with unplasticized PVC pressure pipes Injection moulded unplasticized PVC fittings for solvent welding for use with pressure pipes, including potable water supply
BS EN 681-2:2000	Elastomeric seals. Material requirements for pipe joint seals used in water and drainage applications Thermoplastic elastomers
BS EN 752-4:1998	Drain and sewer systems outside buildings Hydraulic design and environmental considerations
ISO 2078:1993	Textile glass Yarns Designation
BS EN 45011:1998	General requirements for bodies operating product certification systems
BS ISO 472:1988	Plastics. Vocabulary
BS EN 752-3:1997	Drain and sewer systems outside buildings Planning
BS 3447:1962	Glossary of terms used in the glass industry
BS EN 124:1994	Gully tops and manhole tops for vehicular and pedestrian areas. Design requirements, type testing, marking, quality control
BS EN 681-4:2000	Elastomeric seals. Material requirements for pipe joint seals used in water and drainage applications Cast polyurethane sealing elements
BS EN 1401-1:2009	Plastic piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinyl chloride) (PVC-U) Specifications for pipes, fittings and the system
BS EN 752-1:1996	Drain and sewer systems outside buildings Generalities and definitions