BS CECC 16000-1:1992
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
15-07-1996
English
01-05-1992
Foreword
Preface
Section 1 - Scope
Section 2 - General
Section 3 - Terms and definitions
Section 4 - Quality assessment procedures
Section 5 - Test and measurement procedures
Annex A - Free Particle Noise Test
Pertains to electromechanical all-or nothing relays of assessed quality.
Committee |
W/-
|
DevelopmentNote |
Supersedes BS CECC 16000(1980) and 86/29383 DC. Superseded by BS EN 116000-1 and BS EN 116000-3 but remains current. Inactive for the new design. (01/2006)
|
DocumentType |
Standard
|
Pages |
92
|
PublisherName |
British Standards Institution
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
Standards | Relationship |
CECC 16000 PT1 : 90 AMD 2 92 | Identical |
BS CECC16200(1992) : 1992 AMD 9627 | HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS - SECTIONAL SPECIFICATION - ELECTROMECHANICAL ALL OR NOTHING RELAYS |
BS EN 116300:1994 | Harmonized system of quality assessment for electronic components. Sectional specification: electromechanical all-or-nothing heavy load relays of assessed quality (rated from 5A and above) |
BS 5555:1993 | Specification for SI units and recommendations for the use of their multiples and of certain other units |
BS 2011-2.1Fda:1973 | Environmental testing. Tests Test Fda. Random vibration - wide band reproducibility high |
BS 5420:1977 | Specification for degrees of protection of enclosures of switchgear and controlgear for voltages up to and including 1000 V a.c. and 1200 V d.c. |
CECC 00109 : 1974 | CECC RULES OF PROCEDURE: RP 9: CERTIFIED TESTS RECORDS |
BS 2011-2.2Kd:1984 | Environmental testing. Guidance Test Kd. Guidance on Test Kd: Hydrogen sulphide test for contacts and connections |
BS 2011-2.1Ka:1977 | Basic enviromental testing proceedures Tests. Test Ka: Salt mist |
BS 5992-4:1983 | Electrical relays Specification for contact loads of preferred values used in endurance tests for electrical relay contacts |
BS 2011-2.1M:1984 | Environmental testing. Tests Test M. Low air pressure |
IEC 60068-1:2013 | Environmental testing - Part 1: General and guidance |
IEC 60695-2-1:1991 | Fire hazard testing - Part 2: Test methods - Section 1: Glow-wire test and guidance |
BS 5992-3:1980 | Electrical relays Specification for the insulation testing of electrical relays |
IEC 60068-2-27:2008 | Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock |
BS 2011-2.1Fd:1973 | Environmental testing. Tests Test Fd. Random vibration - wide band, general requirements |
IEC 60068-2-20:2008 | Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads |
BS CECC 00109:1991 | Rule of Procedure 9. Certified test records |
IEC 60068-2-49:1983 | Basic environmental testing procedures - Part 2-49: Tests - Guidance to test Kc: Sulphur dioxide test for contacts and connections |
IEC 60068-2-21:2006 | Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices |
IEC 60068-2-13:1983 | Basic environmental testing procedures - Part 2-13: Tests - Test M: Low air pressure |
CECC 00100 : 1988 | BASIC RULES - TO BE USED IN CONNECTION WITH THE INTERNAL REGULATIONS OF THE FEN e.V |
IEC 60068-2-11:1981 | Basic environmental testing procedures - Part 2-11: Tests - Test Ka: Salt mist |
BS 6001-1(1999) : 1999 | SAMPLING PROCEDURES FOR INSPECTION BY ATTRIBUTES - PART 1: SAMPLING SCHEMES INDEXED BY ACCEPTANCE QUALITY LIMIT (AQL) FOR LOT-BY-LOT INSPECTION |
ISO 60:1977 | Plastics — Determination of apparent density of material that can be poured from a specified funnel |
BS 2011-2.1XA(1981) : 1981 AMD 7553 | ENVIRONMENTAL TESTING - TESTS - TEST XA AND GUIDANCE - IMMERSION IN CLEANING SOLVENTS |
IEC 60027-1:1992 | Letters symbols to be used in electrical technology - Part 1: General |
BS 2011-2.1N:1985 | Environmental testing. Tests Test N. Change of temperature |
BS 2045:1965 | Preferred numbers |
BS 6458-2.1:1984 | Fire hazard testing for electrotechnical products. Test methods Glow-wire test |
BS 6493-3:1985 | Semiconductor devices Mechanical and climatic test methods |
IEC 60255-0-20:1974 | Electrical relays - Contact performance of electrical relays |
IEC 60255-15:1981 | Electrical relays. Part 15: Endurance tests for electrical relay contacts - Specification for the characteristics of test equipment |
BS 5992-5:1983 | Electrical relays Specification for test equipment used in endurance tests for electrical relay contacts |
IEC 60410:1973 | Sampling plans and procedures for inspection by attributes |
IEC 60068-2-47:2005 | Environmental testing - Part 2-47: Test - Mounting of specimens for vibration, impact and similar dynamic tests |
BS 5148:1975 | Method for specifying the performance of stabilized power supply apparatus |
IEC 60068-2-3:1969 | Basic environmental testing procedures - Part 2-3: Tests - Test Ca: Damp heat, steady state |
ISO/R 27:1956 | Withdrawal of ISO/R 27-1956 |
IEC 60068-2-17:1994 | Basic environmental testing procedures - Part 2-17: Tests - Test Q: Sealing |
IEC 60068-2-10:2005 | Environmental testing - Part 2-10: Tests - Test J and guidance: Mould growth |
IEC 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
IEC 60255-14:1981 | Electrical relays. Part 14: Endurance tests for electrical relay contacts - Preferred values for contact loads |
BS 5992-1:1980 | Electrical relays Specification for contact performance of electrical relays |
IEC 60255-5:2000 | Electrical Relays - Part 5: Insulation coordination for measuring relays and protection equipment - Requirements and tests |
IEC 60068-2-29:1987 | Environmental testing. Part 2: Tests. Test Eb and guidance: Bump |
IEC 60443:1974 | Stabilized supply apparatus for measurement |
MIL-STD-202 Revision H:2015 | ELECTRONIC AND ELECTRICAL COMPONENT PARTS |
IEC 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
IEC 60144:1963 | Degrees of protection of enclosures for low-voltage switchgear and controlgear |
IEC 60068-2-14:2009 | Environmental testing - Part 2-14: Tests - Test N: Change of temperature |
CECC 00007 : 1978 | BASIC SPECIFICATION: SAMPLING PLANS AND PROCEDURES FOR INSPECTION BY ATTRIBUTES |
BS 2011-2.1GA(1977) : LATEST | BASIC ENVIRONMENTAL TESTING PROCEDURES - TESTS - ACCELERATION, STEADY STATE |
BS 2011-2.1Fdc:1973 | Environmental testing. Tests Test Fdc. Random vibration - wide band reproducibility low |
BS 2011-2.1Fdb:1973 | Environmental testing. Tests Test Fdb. Random vibration - wide band reproducibility medium |
BS 2011-4.1:1983 | Basic enviromental testing proceedures Specification for mounting of components, equipment and other articles for dynamic tests. |
IEC 60068-2-46:1982 | Basic environmental testing procedures - Part 2-46: Tests - Guidance to test Kd: Hydrogen sulphide test for contacts and connections |
BS 2011-2.1T:1981 | Environmental testing. Tests Test T. Soldering |
IEC 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.