We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • BS EN 10028-6:2017 (published 2017-08)

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    Flat products made of steels for pressure purposes Weldable fine grain steels, quenched and tempered

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  25-08-2017

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    European foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Tolerances on dimensions
    5 Calculation of mass
    6 Classification and designation
    7 Information to be supplied by the purchaser
    8 Requirements
    9 Inspection
    10 Sampling
    11 Test methods
    12 Marking
    Annex A (informative) - Information on weldability
    Annex B (informative) - Changes to the previous version
            EN 10028-6:2009
    Annex ZA (informative) - Relationship between this
             European Standard and the Essential Requirements
             of Directive 2014/68/EU aimed to be covered

    Abstract - (Show below) - (Hide below)

    Defines the requirements for flat products for pressure equipment made of weldable fine grain steels, quenched and tempered, as specified in Table 1.

    Scope - (Show below) - (Hide below)

    This European Standard specifies the requirements for flat products for pressure equipment made of quenched and tempered steels as specified in Table 1. The requirements in FprEN 10028-1:2017 also apply. NOTE Once this European Standard is published in the EU Official Journal (OJEU) under Directive 2014/68/EU, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 2014/68/EU is limited to technical data of materials in this European Standard (Part 1 and the other relevant part of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 2014/68/EU are satisfied, needs to be done.

    General Product Information - (Show below) - (Hide below)

    Committee ISE/107
    Development Note Supersedes 08/30187567 DC. (07/2009) Supersedes 14/30312167 DC. (09/2017)
    Document Type Standard
    Publisher British Standards Institution
    Status Current
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    07/30160560 DC : DRAFT JAN 2007 PD 5500 AMD 2 - SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS
    BS PD5500(2003) : 2003 SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS
    BS PD5500(2018) : 2018 SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS
    BS PD5500(2006) : 2006 SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS
    BS PD5500(2009) : 2009 SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS
    BS PD5500(2015) : 2015 SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS
    BS PD5500(2012) : 2012 SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 10028-1:2017 (edition 2) Flat products made of steels for pressure purposes - Part 1: General requirements
    EN 1011-1 : 2009 WELDING - RECOMMENDATIONS FOR WELDING OF METALLIC MATERIALS - PART 1: GENERAL GUIDANCE FOR ARC WELDING
    EN 1011-2:2001/A1:2003 WELDING - RECOMMENDATIONS FOR WELDING OF METALLIC MATERIALS - PART 2: ARC WELDING OF FERRITIC STEELS
    EN 10204 : 2004 METALLIC PRODUCTS - TYPES OF INSPECTION DOCUMENTS
    EN 10020 : 2000 DEFINITION AND CLASSIFICATION OF GRADES OF STEEL
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective