We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • BS EN 10209:2013 (published 2013-07)

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    Cold rolled low carbon steel flat products for vitreous enameling. Technical delivery conditions

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  31-07-2013

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Designation
    5 Requirements
    6 Tests
    7 Identification
    8 Packaging
    9 Disputes
    10 Information to be supplied by the purchaser at the
       time of ordering
    Annex A (normative) - Methods for determining the resistance
            to fish scaling of a steel sheet for enamelling
    Annex B (normative) - Method for determining mass loss (iron loss)
            due to pickling for steel grades for direct enamelling
            in accordance with 5.4.2
    Annex C (normative) - Method for determining the adherence level
            of enamel applied to a steel sheet
    Annex D (informative) - Characteristics for the selection of
            enamelling steel grades



    Abstract - (Show below) - (Hide below)

    Pertains to cold rolled non-coated low carbon steel flat products in rolled widths equal to or over 600 mm and in thicknesses equal to or less than 3 mm, delivered in sheet, wide strip, slit wide strip or cut lengths obtained from slit wide strip or sheet.

    Scope - (Show below) - (Hide below)

    This European Standard applies to cold rolled non-coated low carbon steel flat products in rolled widths equal to or over 600 mm and in thicknesses equal to or less than 3 mm, delivered in sheet, wide strip, slit wide strip or cut lengths obtained from slit wide strip or sheet. It does not apply to cold rolled narrow strip (rolling width < 600 mm) nor to cold rolled flat products for which there is a specific standard, in particular the following: - cold-rolled low carbon steel flat products for cold forming (EN 10130); - cold-rolled non oriented electrical steel sheet and strip delivered in fully processed state (EN 10106); - cold rolled electrical non-alloy and alloy steel sheet and strip delivered in the semi-processed state (EN 10341); - cold reduced blackplate (EN 10205); - steel sheet and strip for welded gas cylinders (EN 10120); - cold-rolled uncoated non-alloy mild steel narrow strip for cold forming (EN 10139); - cold-rolled structural steels for general purposes; - cold-rolled flat products made of high yield strength for cold forming (EN 10268).

    General Product Information - (Show below) - (Hide below)

    Committee ISE/109
    Development Note Supersedes BS 1449-1.3(1991) and 92/37552 DC. (07/2005) Supersedes 10/30227692 DC. (07/2013)
    Document Type Standard
    Publisher British Standards Institution
    Status Current
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS 7793-2(1996) : 1996 VITREOUS ENAMEL COATINGS FOR USE ON BOLTED STEEL PANELS - SPECIFICATION FOR COATINGS ON BOLTED STEEL PANELS FOR USE IN INDUSTRIAL LIQUID STORAGE TANKS

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 10079 : 2007 DEFINITION OF STEEL PRODUCTS
    EN 10027-2 : 2015 DESIGNATION SYSTEMS FOR STEELS - PART 2: NUMERICAL SYSTEM
    EN ISO 6892-1 : 2016 METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT ROOM TEMPERATURE (ISO 6892-1:2016)
    EN ISO 377 : 2017 STEEL AND STEEL PRODUCTS - LOCATION AND PREPARATION OF SAMPLES AND TEST PIECES FOR MECHANICAL TESTING (ISO 377:2017)
    ISO 6892-1:2016 Metallic materials Tensile testing Part 1: Method of test at room temperature
    EN 10131 : 2006 COLD ROLLED UNCOATED AND ZINC OR ZINC-NICKEL ELECTROLYTICALLY COATED LOW CARBON AND HIGH YIELD STRENGTH STEEL FLAT PRODUCTS FOR COLD FORMING - TOLERANCES ON DIMENSIONS AND SHAPE
    EN 10021 : 2006 GENERAL TECHNICAL DELIVERY CONDITIONS FOR STEEL PRODUCTS
    EN 10204 : 2004 METALLIC PRODUCTS - TYPES OF INSPECTION DOCUMENTS
    EN 10049 : 2013 MEASUREMENT OF ROUGHNESS AVERAGE RA AND PEAK COUNT RPC ON METALLIC FLAT PRODUCTS
    EN 10027-1 : 2016 DESIGNATION SYSTEMS FOR STEELS - PART 1: STEEL NAMES
    ISO 10113:2006 Metallic materials Sheet and strip Determination of plastic strain ratio
    ISO 377:2017 Steel and steel products Location and preparation of samples and test pieces for mechanical testing
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective