• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

BS EN 124-6:2015

Current
Current

The latest, up-to-date edition.

Gully tops and manhole tops for vehicular and pedestrian areas Gully tops and manhole tops made of polypropylene (PP), polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC-U)
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

31-07-2015

Foreword
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviations
4 Materials
5 Requirements
6 Testing
7 Assessment and verification of constancy of
  performance - AVCP
8 Designation
9 Marking
Annex A (normative) - Characteristics of glass fibres used for
        reinforcement of PP polymer
Annex B (normative) - Test of deflection under load
Annex ZA (informative) - Clauses of this European Standard
         addressing the provisions of the EU Construction
         Products Regulation
Bibliography

Pertains to manhole tops and gully tops made of Polypropylene (PP), Polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC-U) by a moulding or extrusion process, with a clear opening up to and including 1000 mm for covering gullies, manholes and inspection chambers for installation within areas subjected to pedestrian and/or vehicular traffic.

This European Standard applies to manhole tops and gully tops made of Polypropylene (PP), Polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC-U) by a moulding or extrusion process, with a clear opening up to and including 1000mm for covering gullies, manholes and inspection chambers for installation within areas subjected to pedestrian and/or vehicular traffic. It is applicable to manhole tops and gully tops for use in areas which can only be used by pedestrians and pedal cyclists (class A 15), and pedestrian areas and comparable areas, car parks or car parking decks (class B 125). This European Standard gives guidance for combinations of covers/grating made of PP, PE or PVC–U with frames according to EN124‑2 , EN124‑3 , EN124‑4 and EN124‑5 . This European Standard is not applicable in isolation but only in combination with EN124‑1 . This European Standard is not applicable to: rodding point covers according to EN13598‑1 ; gratings/covers as part of prefabricated drainage channels according to EN1433 ; floor and roof gullies in buildings which are specified in EN1253 (all parts); surface boxes.

Committee
B/505/4
DevelopmentNote
Together with BS EN 124-1, BS EN 124-2, BS EN 124-3, BS EN 124-4 and BS EN 124-5, it supersedes BS EN 124. Supersedes 12/30265313 DC. (07/2015)
DocumentType
Standard
Pages
42
PublisherName
British Standards Institution
Status
Current
Supersedes

Standards Relationship
EN 124-6:2015 Identical

ISO 4892-1:2016 Plastics Methods of exposure to laboratory light sources Part 1: General guidance
ISO 580:2005 Plastics piping and ducting systems — Injection-moulded thermoplastics fittings — Methods for visually assessing the effects of heating
EN ISO 3126:2005 Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005)
EN 12200-1:2016 Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system
EN ISO 8256:2004 Plastics - Determination of tensile-impact strength (ISO 8256:2004)
EN 124-2:2015 Gully tops and manhole tops for vehicular and pedestrian areas - Part 2: Gully tops and manhole tops made of cast iron
EN 13598-1:2010 Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: Specifications for ancillary fittings including shallow inspection chambers
ISO 3506-1:2009 Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs
EN ISO 4892-1:2016 Plastics - Methods of exposure to laboratory light sources - Part 1: General guidance (ISO 4892-1:2016)
EN ISO 4892-3:2016 Plastics - Methods of exposure to laboratory light sources - Part 3: Fluorescent UV lamps (ISO 4892-3:2016)
ISO 1133-1:2011 Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method
ISO 3127:1994 Thermoplastics pipes — Determination of resistance to external blows — Round-the-clock method
ISO 6964:1986 Polyolefin pipes and fittings Determination of carbon black content by calcination and pyrolysis Test method and basic specification
EN 13598-2:2016 Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for manholes and inspection chambers
EN 607:2004 Eaves gutters and fittings made of PVC-U - Definitions, requirements and testing
ISO 8256:2004 Plastics — Determination of tensile-impact strength
ISO 15100:2000 Plastics Reinforcement fibres Chopped strands Determination of bulk density
EN ISO 9163:2005 Textile glass - Rovings - Manufacture of test specimens and determination of tensile strength of impregnated rovings (ISO 9163:2005)
EN 13823:2010+A1:2014 REACTION TO FIRE TESTS FOR BUILDING PRODUCTS - BUILDING PRODUCTS EXCLUDING FLOORINGS EXPOSED TO THE THERMAL ATTACK BY A SINGLE BURNING ITEM
ISO 9163:2005 Textile glass — Rovings — Manufacture of test specimens and determination of tensile strength of impregnated rovings
ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
EN ISO 1133-1:2011 Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2011)
EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
ISO 4892-3:2016 Plastics Methods of exposure to laboratory light sources Part 3: Fluorescent UV lamps
EN 14758-1:2012 Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system
ISO 1183-1:2012 Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
EN 1433:2002/A1:2005 DRAINAGE CHANNELS FOR VEHICULAR AND PEDESTRIAN AREAS - CLASSIFICATION, DESIGN AND TESTING REQUIREMENTS, MARKING AND EVALUATION OF CONFORMITY
EN 12666-1:2005+A1:2011 Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system
ISO 1183-2:2004 Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method
ISO 9001:2015 Quality management systems — Requirements
EN ISO 580:2005 Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating (ISO 580:2005)
EN 1401-1:2009 Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system
EN 12164:2016 Copper and copper alloys - Rod for free machining purposes
ISO 4892-2:2013 Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
EN 124-4:2015 Gully tops and manhole tops for vehicular and pedestrian areas - Part 4: Gully tops and manhole tops made of steel reinforced concrete
EN 16245-3:2013 Fibre-reinforced plastic composites - Declaration of raw material characteristics - Part 3: Specific requirements for fibre
EN 124-3:2015 Gully tops and manhole tops for vehicular and pedestrian areas - Part 3: Gully tops and manhole tops made of steel or aluminium alloys
EN 20105-A02 : 1994 TEXTILES - TESTS FOR COLOUR FASTNESS - PART A02: GREYSCALE FOR ASSESSING CHANGE IN COLOUR (ISO 105-A02:1993)
ISO 105-A02:1993 Textiles Tests for colour fastness Part A02: Grey scale for assessing change in colour
ISO 1888:2006 Textile glass Staple fibres or filaments Determination of average diameter
EN 124-5:2015 Gully tops and manhole tops for vehicular and pedestrian areas - Part 5: Gully tops and manhole tops made of composite materials
EN 12201-1:2011 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General
ISO 3506-2:2009 Mechanical properties of corrosion-resistant stainless steel fasteners Part 2: Nuts
ISO 178:2010 Plastics Determination of flexural properties
EN ISO 4892-2:2013 Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon-arc lamps (ISO 4892-2:2013)
EN 513:1999 Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors - Determination of the resistance to artificial weathering
EN 124-1:2015 Gully tops and manhole tops for vehicular and pedestrian areas - Part 1: Definitions, classification, general principles of design, performance requirements and test methods
EN ISO 1183-1:2012 Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012)
ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
EN ISO 1183-2:2004 PLASTICS - METHODS FOR DETERMINING THE DENSITY OF NON-CELLULAR PLASTICS - PART 2: DENSITY GRADIENT COLUMN METHOD

View more information
£232.00
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.