• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

BS EN 12952-8:2002

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Water-tube boilers and auxiliary installations Requirements for firing systems for liquid and gaseous fuels for the boiler
Available format(s)

Hardcopy , PDF

Superseded date

02-11-2022

Language(s)

English

Published date

13-06-2002

Foreword
1 Scope
  1.1 Firing systems
  1.2 Fuels
  1.3 Operation
2 Normative references
3 Terms and definitions
4 Fuel supply
  4.1 General
  4.2 Fuel transfer and preparation
  4.3 Fuel lines
  4.4 Safety shut-off devices (Safety trip valves)
5 Equipment for air supply and flue gas discharge
  5.1 Air supply
  5.2 Air/fuel ratio
  5.3 Flue gas discharge
6 Firing system
  6.1 Burners
  6.2 Flue gas recirculation
  6.3 Control and monitoring
  6.4 Electrical equipment
  6.5 Safety precautions
  6.6 Common stack for several firing systems
7 Operating manual
8 Particular requirements for firing systems burning gaseous
  fuels with high relative density
  8.1 Main firing systems
  8.2 Ignition burner systems
Annex A (normative) Chemical recovery boiler (black liquor
         boiler)
      A.1 General
      A.2 Additional requirements for the firing system for
          black liquor in the chemical recovery boiler
      A.3 Special requirements for oil- or gas-firing for
          chemical recovery boilers
Annex B (informative) Operational requirements for permanent
         supervised firing systems for liquid and gaseous fuels
      B.1 General
      B.2 Operation
      B.3 Fuel preparation
      B.4 Safety shutoff devices
      B.5 Air/fuel ratio
      B.6 Modification of firing, burner or air/fuel
           ratio setting
      B.7 Control and monitoring
      B.8 Purging, start-up and shut down
      B.9 Emergency operation
      B.10 Operating and maintenance instructions
      B.11 Firing systems burning gaseous fuels with relative
           density
Annex ZA (informative) Clauses of this European Standard
         addressing essential safety requirements or other
         provisions of the Pressure Equipment Directives
Bibliography

Gives requirements, for oil and gas firing systems of steam boilers and hot water generators as defined in EN 12952-1.

Committee
PVE/2
DevelopmentNote
Supersedes 98/716514 DC (07/2002)
DocumentType
Standard
Pages
30
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

EN 676:2003+A2:2008/AC:2008 AUTOMATIC FORCED DRAUGHT BURNERS FOR GASEOUS FUELS
EN 13480-2:2017 Metallic industrial piping - Part 2: Materials
EN 751-3:1996/AC:1997 Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 3: Unsintered PTFE tapes
EN 264 : 1991 SAFETY SHUT OFF DEVICES FOR COMBUSTION PLANTS USING LIQUID FUELS - SAFETY REQUIREMENTS AND TESTING
ISO 6976:2016 Natural gas — Calculation of calorific values, density, relative density and Wobbe indices from composition
EN 293:1992 Oil pressure atomizing nozzles - Minimum requirements - Testing
EN 225 : 1987 ATOMIZING OIL BURNERS - PUMPS WITH ROTATING SHAFT & EXTERNAL DRIVE - DIMENSIONS
EN 751-2:1996 Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 2: Non-hardening jointing compounds
PREN 50156-1 : DRAFT 2012 ELECTRICAL EQUIPMENT FOR FURNACES AND ANCILLARY EQUIPMENT - PART 1: REQUIREMENTS FOR APPLICATION DESIGN AND INSTALLATION
ISO 7-2:2000 Pipe threads where pressure-tight joints are made on the threads Part 2: Verification by means of limit gauges
EN 161:2011+A3:2013 Automatic shut-off valves for gas burners and gas appliances
EN 267:2009+A1:2011 Automatic forced draught burners for liquid fuels
EN 1044 : 1999 BRAZING - FILLER METALS
EN 12952-1:2015 Water-tube boilers and auxiliary installations - Part 1: General
EN ISO 3677:2016 Filler metal for soldering and brazing - Designation (ISO 3677:2016)
ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation
ISO 3677:2016 Filler metal for soldering and brazing — Designation
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
EN 230:2005 Automatic burner control systems for oil burners
IEC 60730-2-5:2013+AMD1:2017 CSV Automatic electrical controls - Part 2-5: Particular requirements for automatic electrical burner control systems
EN 751-1:1996 Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 1: Anaerobic jointing compounds
EN 298:2012 Automatic burner control systems for burners and appliances burning gaseous or liquid fuels
EN 88:1991/A1:1996 PRESSURE GOVERNORS FOR GAS APPLIANCES FOR INLET PRESSURE UP TO 200 MBAR
EN 226:1987/AC1:1987 Atomizing oil burners - Connecting dimensions between burners and heat generators
EN 299:2009 Oil pressure atomizing nozzles - Determination of the angle and spray characteristics
ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
EN 12952-5:2011 Water-tube boilers and auxiliary installations - Part 5: Workmanship and construction of pressure parts of the boiler
1997/23/EC : 1997 DIRECTIVE 97/23/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 29 MAY 1997 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING PRESSURE EQUIPMENT
EN 287-1:2011 Qualification test of welders - Fusion welding - Part 1: Steels

View more information
£186.00
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.