• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

BS EN 13043:2013

Withdrawn
Withdrawn

A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

Aggregates for bituminous mixtures and surface treatments for roads, airfields and other trafficked areas
Available format(s)

Hardcopy , PDF

Withdrawn date

19-09-2018

Language(s)

English

Published date

30-11-2013

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements for coarse and fine aggregate
5 Requirements for filler aggregate
6 Evaluation of conformity
7 Designation
8 Marking and labelling
Annex A (informative) - Notes for guidance on the
        freezing and thawing resistance of aggregates
Annex B (normative) - Factory production control
Annex ZA (informative) - Clauses of this European
         Standard addressing essential requirements
         or other provisions of EU Directives
Bibliography

Describes the properties of aggregates and filler aggregates obtained by processing natural, manufactured or recycled materials and mixtures of these aggregates for use in bituminous mixtures and surface treatments for roads, airfields and other trafficked areas.

This European Standard specifies the properties of aggregates and filler aggregates obtained by processing natural, manufactured or recycled materials and mixtures of these aggregates for use in bituminous mixtures and surface treatments for roads, airfields and other trafficked areas. This standard does not cover the use of reclaimed bituminous mixtures3 . It also covers recycled aggregate with densities between 1,50 Mg/m3 (1 500 kg/m3) and 2,00 Mg/m3 (2 000 kg/m3) with appropriate caveats and recycled fine aggregate with appropriate caveats.

A list of the source materials that have been considered and indicating those which are within the scope of this standard is given in Annex A (normative).

Requirements for the evaluation of conformity of the products to this European Standard are given in EN 16236.

It incorporates a general requirement that aggregates shall not release any dangerous substances in excess of the maximum permitted levels specified in a relevant European Standard for the material or permitted in the national regulations of the member state of destination.

The tables in this standard include categories which are common across the four main aggregate standards: EN 12620, EN 13043, EN 13139 and EN 13242. Not all of these categories are appropriate for aggregates for use for bituminous mixtures.

Categories, notes, comments etc., which are grey shaded, should not be used for aggregates for bituminous mixtures.

Aggregates used in construction should comply with all the requirements of the relevant European Standards. These standards include comprehensive and specific requirements for natural aggregates, iron and steel making slag and recycled aggregates, dealing with, for example, the stability of certain basalts, the expansion of certain slags and the constitution of recycled aggregates.

For materials from some other secondary sources, however, work is ongoing and the requirements are incomplete. In the meantime, such materials, when placed on the market as aggregates, should conform fully to this standard but may also be required to conform to specific relevant additional requirements at the place of use. Additional characteristics and requirements may be specified on a case by case basis depending upon experience of use of the product, and defined in specific contractual documents.

NOTE 1 Requirements for lightweight aggregates are specified in EN 13055. Requirements for the declaration of the potential of aggregates to release regulated dangerous substances are currently under development. Until such time as these are finalised, attention should be paid to requirements at the place of use.

NOTE 2 Requirements for reclaimed asphalt for use as a constituent of asphalt mixtures are specified in EN 13108-8 and are not therefore covered in detail in this standard. EN 13108-8 does however call up the general requirements of EN 13043 for the aggregate component of reclaimed asphalt.

Committee
B/502
DevelopmentNote
Supersedes BS 63-1(1987) and BS 63-2(1987) Supersedes 97/107534 DC. (01/2003) 2013 Edition issued on 31/05/2013 is declared withdrawn on 10/01/2014. (02/2014)
DocumentType
Standard
Pages
56
PublisherName
British Standards Institution
Status
Withdrawn
Supersedes

17/30366702 DC : 0 BS PD6689(2017) - SURFACE TREATMENTS - GUIDANCE ON THE USE OF BS EN 12271 AND BS EN 12273
10/30213884 DC : 0 BS 594987 - ASPHALT FOR ROADS AND OTHER PAVED AREAS - SPECIFICATION FOR TRANSPORT, LAYING AND COMPACTION AND TYPE TESTING PROTOCOLS
BS 594987:2007 Asphalt for roads and other paved areas - Specification for transport, laying and compaction and type testing protocols.
BS 8204-3(2004) : 2004 SCREEDS, BASES AND IN SITU FLOORINGS - PART 3: POLYMER MODIFIED CEMENTITIOUS LEVELLING SCREEDS AND WEARING SCREEDS - CODE OF PRACTICE
PD 6682-4:2003 Aggregates Lightweight aggregates for concrete, mortar and grout. Guidance on the use of BS EN 13055-1
14/30283621 DC : 0 PD 6691:2015 - GUIDANCE ON THE USE OF BS EN 13108 BITUMINOUS MIXTURES - MATERIAL SPECIFICATIONS
PD 6682-3:2003 Aggregates Aggregates for mortar. Guidance on the use of BS EN 13139
BS 598-100:2004 Sampling and examination of bituminous mixtures for roads and other paved areas Methods for sampling for analysis
BS 598-102:2003 Sampling and examination of bituminous mixtures for roads and other paved areas Analytical test methods
BS 594987(2015) : 2015 ASPHALT FOR ROADS AND OTHER PAVED AREAS - SPECIFICATION FOR TRANSPORT, LAYING, COMPACTION AND PRODUCT-TYPE TESTING PROTOCOLS
PD 6689:2017 Surface treatments. Guidance on the use of BS EN 12271 and BS EN 12273 Guidance on the use of BS EN 12271 and BS EN 12273
BS 594-2:2003 Hot rolled asphalt for roads and other paved areas Specification for transport, laying and compaction of hot rolled asphalt
BS PD6682-2(2009) : 2009 AGGREGATES - PART 2: AGGREGATES FOR BITUMINOUS MIXTURES AND SURFACE TREATMENTS FOR ROADS, AIRFIELDS AND OTHER TRAFFICKED AREAS - GUIDANCE ON THE USE OF BS EN 13043
BS 4987-1:2003 Coated macadam (asphalt concrete) for roads and other paved areas Specification for constituent materials and for mixtures
BS 594-1:2003 Hot rolled asphalt for roads and other paved areas Specification for constituent materials and asphalt mixtures
BS 594987:2010 Asphalt for roads and other paved areas. Specification for transport, laying, compaction and type testing protocols
BS 594-1:2005 Hot rolled asphalt for roads and other paved areas Specification for constituent materials and asphalt mixtures
BS 598-108:2005 Sampling and examination of bituminous mixtures for roads and other paved areas Methods for determination of the condition of the binder on coated chippings and for measurement of the rate of spread of coated chippings
BS 4987-1:2005 Coated macadam (asphalt concrete) for roads and other paved areas Specification for constituent materials and for mixtures
PD 6689:2009 Surface treatments. Guidance on the use of BS EN 12271 and BS EN 12273
PD 6682-2:2003 Aggregates Aggregates for bituminous mixtures and surface treatments for roads, airfields and other trafficked areas. Guidance on the use of BS EN 13043
PD 6682-8:2004 Aggregates Aggregates for railway ballast. Guidance on the use of BS EN 13450
07/30154860 DC : DRAFT JAN 2007 BS 4987-2 - ASPHALT FOR ROADS AND OTHER PAVED AREAS - SPECIFICATION FOR TRANSPORT, LAYING AND COMPACTION AND DESIGN PROTOCOLS
PD 6682-7:2003 Aggregates Armourstone. Guidance on the use of BS EN 13383
PD 6682-9:2003 Aggregates Guidance on the use of European test method standards
PD 6682-1:2003 Aggregates Aggregates for concrete. Guidance on the use of BS EN 12620
BS 598-107:2004 Sampling and examination of bituminous mixtures for roads and other paved areas Method of test for the determination of the composition of design surface course rolled asphalt
PD 6691:2007 Guidance on the use of BS EN 13108 Bituminous mixtures. Material specifications
PD 6682-5:2005 Aggregates Lightweight aggregates for bituminous mixtures and surface treatments and for unbound and bound applications. Guidance on the use of BS EN 13055-2
PD 6689:2006 Surface dressing. Guidance on the use of BS EN 12271
PD 6691:2010 Guidance on the use of BS EN 13108 Bituminous mixtures. Material specifications
BS PD6691(2015) : 2015 GUIDANCE ON THE USE OF BS EN 13108, BITUMINOUS MIXTURES - MATERIAL SPECIFICATIONS
04/30055996 DC : DRAFT FEB 2004 BS 8204-3 - SCREEDS, BASES AND IN SITU FLOORINGS - PART 3: POLYMER MODIFIED CEMENTITIOUS LEVELLING SCREEDS AND WEARING SCREEDS - CODE OF PRACTICE

EN 196-21 : 1989 METHODS OF TESTING CEMENT - DETERMINATION OF THE CHLORIDE, CARBON DIOXIDE AND ALKALI CONTENT OF CEMENT
EN 13179-1:2013 Tests for filler aggregate used in bituminous mixtures - Part 1: Delta ring and ball test
EN 13179-2:2000 Tests for filler aggregate used in bituminous mixtures - Part 2: Bitumen number
EN 932-2:1999 Tests for general properties of aggregates - Part 2: Methods for reducing laboratory samples
EN 1367-1:2007 Tests for thermal and weathering properties of aggregates - Part 1: Determination of resistance to freezing and thawing
ISO 3310-1:2016 Test sieves Technical requirements and testing Part 1: Test sieves of metal wire cloth
EN 196-2:2013 Method of testing cement - Part 2: Chemical analysis of cement
EN 459-2:2010 Building lime - Part 2: Test methods
EN 932-3:1996/A1:2003 TESTS FOR GENERAL PROPERTIES OF AGGREGATES - PART 3: PROCEDURE AND TERMINOLOGY FOR SIMPLIFIED PETROGRAPHIC DESCRIPTION
EN 1097-8:2009 Tests for mechanical and physical properties of aggregates - Part 8: Determination of the polished stone value
EN 933-3:2012 Tests for geometrical properties of aggregates - Part 3: Determination of particle shape - Flakiness index
ISO 565:1990 Test sieves — Metal wire cloth, perforated metal plate and electroformed sheet — Nominal sizes of openings
EN 1097-5:2008 Tests for mechanical and physical properties of aggregates - Part 5: Determination of the water content by drying in a ventilated oven
EN 933-6:2014 Tests for geometrical properties of aggregates - Part 6: Assessment of surface characteristics - Flow coefficient of aggregates
EN 933-10:2009 Tests for geometrical properties of aggregates - Part 10: Assessment of fines - Grading of filler aggregates (air jet sieving)
EN 1744-1:2009+A1:2012 Tests for chemical properties of aggregates - Part 1: Chemical analysis
EN 1097-3:1998 Tests for mechanical and physical properties of aggregates - Part 3: Determination of loose bulk density and voids
EN 933-9:2009+A1:2013 Tests for geometrical properties of aggregates - Part 9: Assessment of fines - Methylene blue test
EN 1097-2:2010 Tests for mechanical and physical properties of aggregates - Part 2: Methods for the determination of resistance to fragmentation
EN 933-2:1995 Tests for geometrical properties of aggregates - Part 2: Determination of particle size distribution - Test sieves, nominal size of apterures
EN 1367-2:2009 Tests for thermal and weathering properties of aggregates - Part 2: Magnesium sulfate test
EN 933-1:2012 Tests for geometrical properties of aggregates - Part 1: Determination of particle size distribution - Sieving method
EN 1367-5:2011 Tests for thermal and weathering properties of aggregates - Part 5: Determination of resistance to thermal shock
EN 932-5:2012/AC:2014 TESTS FOR GENERAL PROPERTIES OF AGGREGATES - PART 5: COMMON EQUIPMENT AND CALIBRATION
EN 1097-1:2011 Tests for mechanical and physical properties of aggregates - Part 1: Determination of the resistance to wear (micro-Deval)
EN 933-4:2008 Tests for geometrical properties of aggregates - Part 4: Determination of particle shape - Shape index
EN 1097-4:2008 Tests for mechanical and physical properties of aggregates - Part 4: Determination of the voids of dry compacted filler
EN 1097-9:2014 Tests for mechanical and physical properties of aggregates - Part 9: Determination of the resistance to wear by abrasion from studded tyres - Nordic test
EN 1097-7:2008 Tests for mechanical and physical properties of aggregates - Part 7: Determination of the particle density of filler - Pyknometer method
EN 1097-6:2013 Tests for mechanical and physical properties of aggregates - Part 6: Determination of particle density and water absorption
EN 1367-3:2001/AC:2004 TESTS FOR THERMAL AND WEATHERING PROPERTIES OF AGGREGATES - PART 3: BOILING TEST FOR "SONNENBRAND BASALT"
EN 933-5:1998/A1:2004 TESTS FOR GEOMETRICAL PROPERTIES OF AGGREGATES - PART 5: DETERMINATION OF PERCENTAGE OF CRUSHED AND BROKEN SURFACES IN COARSE AGGREGATE PARTICLES

View more information
£276.00
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.