• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

BS EN 1360:2013

Current
Current

The latest, up-to-date edition.

Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems. Specification
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

30-06-2013

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Materials and construction
6 Pressure requirements
7 Dimensions and tolerances
8 Physical properties
9 End fittings
10 Type tests
11 Frequency of testing
12 Marking
Annex A (normative) - Test method for determination
        of low temperature resistance at -30 degrees C
        (for normal temperature class) and -40 degrees C
        (for low temperature class)
Annex B (normative) - Method for the determination
        of adhesion between components
Annex C (normative) - Test method for the determination
        of low temperature flexibility
Annex D (normative) - Test method for the determination
        of fuel permeation
Annex E (normative) - Test method for flammability
Annex F (normative) - End-fitting pull-off test
Annex G (normative) - Test method for the determination
        of leakage (leak test)
Annex H (normative) - Test method for fatigue strength
        under reversed bending stress (flex test)
Annex I (normative) - Test frequency for type tests and
        routine tests
Annex J (informative) - Test frequency for production
        acceptance tests
Bibliography

Describes minimum requirements and test methods for verification for three types of hoses in two grades and two classes of hose assemblies used for measured fuel dispensing, including oxygenated fuels (up to a maximum of 15% oxygenated compounds).

This European Standard specifies minimum requirements and test methods for verification for three types of hoses in two grades and two classes of hose assemblies used for measured fuel dispensing, including oxygenated fuels (up to a maximum of 15 % oxygenated compounds). The assemblies are intended for use at ambient temperatures between –30 °C and +55 °C for normal temperature class and –40 °C and +55 °C for low temperature class at a working pressure ? 16 bar ). As part of the certification of a new dispenser, testing of fuel samples in accordance with EN 228 and EN 590 should be carried out at least eight weeks after the first use of the equipment to avoid unrepresentative sulphur content results.

Committee
PRI/66
DevelopmentNote
Supersedes BS 3395(1989) and 93/312306 DC. (09/2005) Supersedes 03/300797 DC. (10/2005) Supersedes 11/30250270 DC. (07/2013)
DocumentType
Standard
Pages
32
PublisherName
British Standards Institution
Status
Current
Supersedes

Standards Relationship
NS EN 1360 : 2013 Identical
UNI EN 1360 : 2013 Identical
NBN EN 1360 : 2013 Identical
I.S. EN 1360:2013 Identical
EN 1360:2013 Identical
NF EN 1360 : 2013 Identical
SN EN 1360:2013 Identical
NEN EN 1360 : 2013 Identical
UNE-EN 1360:2013 Identical

BS 5502-25:1991 Buildings and structures for agriculture Code of practice for design and installation of services and facilities
BS PAS 022(1997) : 1997 AMD 10113 SPECIFICATION FOR CONSTRUCTION OF VAPOUR RECOVERY SYSTEMS INSTALLED IN PETROL METERING PUMPS AND DISPENSERS

EN ISO 8330:2014 Rubber and plastics hoses and hose assemblies - Vocabulary (ISO 8330:2014)
EN ISO 1402:2009 Rubber and plastics hoses and hose assemblies - Hydrostatic testing (ISO 1402:2009)
EN ISO 4671:2007/A1:2011 Rubber and plastics hoses and hose assemblies - Methods of measurement of the dimensions of hoses and the lengths of hose assemblies - Amendment 1: Clarification of position at which outside diameter is measured (ISO 4671:2007/Amd 1:2011)
EN 228:2012+A1:2017 Automotive fuels - Unleaded petrol - Requirements and test methods
ISO 6801:1983 Rubber or plastics hoses Determination of volumetric expansion
ISO 4649:2017 Rubber, vulcanized or thermoplastic — Determination of abrasion resistance using a rotating cylindrical drum device
EN ISO 1307:2008 Rubber and plastics hoses - Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses (ISO 1307:2006)
ISO 188:2011 Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
EN ISO 8031:2009 Rubber and plastics hoses and hose assemblies - Determination of electrical resistance and conductivity (ISO 8031:2009)
EN ISO 7326:2016 Rubber and plastics hoses - Assessment of ozone resistance under static conditions (ISO 7326:2016)
ISO 7326:2016 Rubber and plastics hoses Assessment of ozone resistance under static conditions
EN ISO 8033:2017 Rubber and plastics hoses - Determination of adhesion between components (ISO 8033:2016)
ISO 8330:2007 Rubber and plastics hoses and hose assemblies Vocabulary
ISO 10619-1:2011 Rubber and plastics hoses and tubing Measurement of flexibility and stiffness Part 1: Bending tests at ambient temperature
EN 26801:1993/A1:2011 RUBBER OR PLASTICS HOSES - DETERMINATION OF VOLUMETRIC EXPANSION (ISO 6801:1983/AMD 1:2011)
ISO 37:2017 Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
ISO 4671:2007 Rubber and plastics hoses and hose assemblies Methods of measurement of the dimensions of hoses and the lengths of hose assemblies
ISO 554:1976 Standard atmospheres for conditioning and/or testing — Specifications
ISO 1402:2009 Rubber and plastics hoses and hose assemblies Hydrostatic testing
ISO 1307:2006 Rubber and plastics hoses — Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses
ISO 8033:2016 Rubber and plastics hoses Determination of adhesion between components
ISO 8031:2009 Rubber and plastics hoses and hose assemblies Determination of electrical resistance and conductivity
ISO 1817:2015 Rubber, vulcanized or thermoplastic Determination of the effect of liquids

View more information
£198.00
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.