We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • BS EN 13924:2006

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    Bitumen and bituminous binders. Specifications for hard paving grade bitumens

    Available format(s):  Hardcopy, PDF

    Superseded date:  30-06-2016

    Language(s):  English

    Published date:  31-10-2011

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and Definitions
    4 Sampling
    5 Requirements and test methods
    6 Evaluation of conformity
    Annex A (normative) - Calculation of the penetration index
    Annex B (informative) - Informative properties
    Annex ZA (informative) - Clauses of this European Standard
             addressing the provisions of the EU Construction
             Products Directive
    Bibliography
    National Annex NA (informative) - Guidance for use of
                      BS EN 13924 in the UK

    Abstract - (Show below) - (Hide below)

    Provides a framework for specifying the properties and relevant test methods for hard paving grade bitumens which are suitable for use in the construction and maintenance of roads, airfields and other paved areas.

    Scope - (Show below) - (Hide below)

    This document provides a framework for specifying the properties and relevant test methods for hard paving grade bitumens which are suitable for use in the construction and maintenance of roads, airfields and other paved areas.

    This framework covers three essential characteristics according to the mandate M/124: EU Construction Products Directive 89/106/EEC :

    • \'Consistency at intermediate service temperature\';

    • \'Consistency at elevated service temperature\';

    • \'Durability\' of the above.

    General Product Information - (Show below) - (Hide below)

    Committee B/510/19
    Development Note Supersedes 00/106660 DC. (05/2006) Together with BS EN 12591, it supersedes BS 3690-1(1989). (06/2011)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS 3690-1(1989) : 1989 BITUMENS FOR BUILDING AND CIVIL ENGINEERING - PART 1: SPECIFICATION FOR BITUMENS FOR ROADS AND OTHER PAVED AREAS
    14/30283621 DC : 0 PD 6691:2015 - GUIDANCE ON THE USE OF BS EN 13108 BITUMINOUS MIXTURES - MATERIAL SPECIFICATIONS
    PD 6691:2007 GUIDANCE ON THE USE OF BS EN 13108 BITUMINOUS MIXTURES - MATERIAL SPECIFICATIONS
    PD 6691:2010 Guidance on the use of BS EN 13108 Bituminous mixtures. Material specifications
    BS PD6691(2015) : 2015 GUIDANCE ON THE USE OF BS EN 13108, BITUMINOUS MIXTURES - MATERIAL SPECIFICATIONS

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 12592:2014 Bitumen and bituminous binders - Determination of solubility
    EN 1426:2015 Bitumen and bituminous binders - Determination of needle penetration
    ISO 2719:2016 Determination of flash point Pensky-Martens closed cup method
    EN 12697-12:2008 Bituminous mixtures - Test methods for hot mix asphalt - Part 12: Determination of the water sensitivity of bituminous specimens
    EN 12697-1 : 2012 COR 2012 BITUMINOUS MIXTURES - TEST METHODS FOR HOT MIX ASPHALT - PART 1: SOLUBLE BINDER CONTENT
    EN 12596:2014 Bitumen and bituminous binders - Determination of dynamic viscosity by vacuum capillary
    EN 12697-11:2012 BITUMINOUS MIXTURES - TEST METHODS FOR HOT MIX ASPHALT - PART 11: DETERMINATION OF THE AFFINITY BETWEEN AGGREGATE AND BITUMEN
    EN 1427:2015 Bitumen and bituminous binders - Determination of the softening point - Ring and Ball method
    89/106/EEC : 1988 COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS
    EN 14770:2012 Bitumen and bituminous binders - Determination of complex shear modulus and phase angle - Dynamic Shear Rheometer (DSR)
    EN 12597:2014 (edition 2) Bitumen and bituminous binders - Terminology
    EN 12697-26:2012 Bituminous mixtures - Test methods for hot mix asphalt - Part 26: Stiffness
    EN 58:2012 Bitumen and bituminous binders - Sampling bituminous binders
    EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
    ISO 4259:2006 Petroleum products Determination and application of precision data in relation to methods of test
    EN 12594:2014 (edition 2) Bitumen and bituminous binders - Preparation of test samples
    ISO 9001:2015 Quality management systems — Requirements
    EN 12607-3:2014 Bitumen and bituminous binders - Determination of the resistance to hardening under influence of heat and air - Part 3: RFT method
    EN ISO 2719:2016 Determination of flash point - Pensky-Martens closed cup method (ISO 2719:2016)
    EN 12607-1:2014 Bitumen and bituminous binders - Determination of the resistance to hardening under influence of heat and air - Part 1: RTFOT method
    EN 12593:2015 BITUMEN AND BITUMINOUS BINDERS - DETERMINATION OF THE FRAASS BREAKING POINT
    EN ISO 2592:2017 Petroleum and related products - Determination of flash and fire points - Cleveland open cup method (ISO 2592:2017)
    EN 12591:2009 Bitumen and bituminous binders - Specifications for paving grade bitumens
    EN 14771:2012 Bitumen and bituminous binders - Determination of the flexural creep stiffness - Bending Beam Rheometer (BBR)
    EN ISO 4259:2006 Petroleum products - Determination and application of precision data in relation to methods of test (ISO 4259:2006)
    EN 12595:2014 Bitumen and bituminous binders - Determination of kinematic viscosity
    CEN/TR 15352:2006 Bitumen and bituminous binders - Development of performance-related specifications: status report 2005
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective