• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

BS EN 14188-1:2004

Current
Current

The latest, up-to-date edition.

Joint fillers and sealants Specifications for hot applied sealants
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

29-09-2004

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Classification and specification
  4.1 Joint sealant
  4.2 Primer
5 Requirements
  5.1 Shelf life
  5.2 Compliance to requirements after safe heating temperature
  5.3 Softening point
  5.4 Density
  5.5 Cone penetration
  5.6 Penetration and recovery at +25 Degrees C (resilience)
  5.7 Heat stability
  5.8 Flow resistance
  5.9 Resistance to fuel immersion (solubility)
  5.10 Compatibility with asphalt pavements
  5.11 Bonding strength
  5.12 Cohesion
  5.13 Dangerous substances
6 Evaluation of conformity
  6.1 General
  6.2 Type Testing
       6.2.1 Initial Type Testing (ITT)
       6.2.2 Further Type Testing
  6.3 Factory Production Control (FPC)
       6.3.1 General
       6.3.2 Frequency of testing
       6.3.3 Equipment
       6.3.4 Raw materials and components
       6.3.5 Design process
       6.3.6 Non-conforming products
7 Marking, labelling and packaging
  7.1 General
  7.2 Hot applied joint sealant
  7.3 Primer
  7.4 Containers
Annex A (normative) Initial Type Testing and frequencies of
        testing for Factory Production Control
Annex B (informative) Example of a product data sheet
      B.1 General information
Annex ZA (informative) Clauses of this European Standard
         addressing essential requirements or other provisions
         of EU Directives
      ZA.1 Scope and relevant characteristics
      ZA.2 Procedure(s) for attestation of conformity
           ZA.2.1 Systems of attestation of conformity
           ZA.2.2 EC Certificate and declaration of conformity
      ZA.3 CE marking and labelling
Bibliography

Describes the requirements for hot-applied normal and fuel resistant joint sealants to be used in roads, airfields and other trafficked areas.

This document specifies requirements for hot-applied normal and fuel resistant joint sealants to be used in roads, airfields and other trafficked areas. The specification also applies to hot-applied normal joint sealants in bituminous surfacing and between bituminous surfacing and concrete pavements.

Committee
B/510/3
DevelopmentNote
Supersedes BS 2499-1(1993) (09/2004) Supersedes 01/103314 DC (10/2004)
DocumentType
Standard
Pages
24
PublisherName
British Standards Institution
Status
Current
Supersedes

BS 5385-3:2014 Wall and floor tiling Design and installation of internal and external ceramic and mosaic floor tiling in normal conditions. Code of practice
14/30283603 DC : 0 BS 5385-3 - WALL AND FLOOR TILING - PART 3: DESIGN AND INSTALLATION OF INTERNAL ANDEXTERNAL CERAMIC AND MOSAIC FLOOR TILING IN NORMAL CONDITIONS - CODE OF PRACTICE
08/30043515 DC : DRAFT FEB 2008 BS 5385-1 - WALL AND FLOOR TILING - PART 1: DESIGN AND INSTALLATION OF CERAMIC AND NATURAL STONE AND MOSAIC WALL TILING IN NORMAL INTERNAL CONDITIONS - CODE OF PRACTICE

EN 1427:2015 Bitumen and bituminous binders - Determination of the softening point - Ring and Ball method
89/106/EEC : 1988 COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS
EN 13880-11:2003 Hot applied joint sealants - Part 11: Test method for the preparation of asphalt test blocks used in the function test and for the determination of compatibility with asphalt pavements
EN 13880-8:2003 HOT APPLIED JOINT SEALANTS - PART 8: TEST METHOD FOR THE DETERMINATION OF THE CHANGE IN WEIGHT OF FUEL RESISTANCE JOINT SEALANTS AFTER FUEL IMMERSION
EN 13880-3:2003 Hot applied joint sealants - Part 3: Test method for the determination of penetration and recovery (resilience)
EN 13880-4:2003 Hot applied joint sealants - Part 4: Test method for the determination of heat resistance - Change in penetration value
EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
EN 13880-7:2003 HOT APPLIED JOINT SEALANTS - PART 7: FUNCTION TESTING OF JOINT SEALANTS
EN 13880-9 : 2003 HOT APPLIED JOINT SEALANTS - PART 9: TEST METHOD FOR THE DETERMINATION OF COMPATIBILITY WITH ASPHALT PAVEMENTS
ISO 9001:2015 Quality management systems — Requirements
EN 13880-5:2004 Hot applied joint sealants - Part 5: Test method for the determination of flow resistance
EN 13880-2 : 2003 HOT APPLIED JOINT SEALANTS - PART 2: TEST METHOD FOR THE DETERMINATION OF CONE PENETRATION AT 25 DEGREES C
EN 13880-6:2004 HOT APPLIED JOINT SEALANTS - PART 6: METHOD FOR THE PREPARATION OF SAMPLES FOR TESTING
EN 13880-13:2003 HOT APPLIED JOINT SEALANTS - PART 13: TEST METHOD FOR THE DETERMINATION OF THE DISCONTINUOUS EXTENSION (ADHERENCE TEST)
EN 13880-1:2003 Hot applied joint sealants - Part 1: Test method for the determination of density at 25 °C

View more information
£186.00
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.