We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • BS EN 14188-3 : 2005

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    JOINT FILLERS AND SEALANTS - PART 3: SPECIFICATIONS FOR PREFORMED JOINT SEALS

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2005

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Classification
    5 Requirements
      5.1 General
      5.2 Dimensional tolerances
      5.3 Imperfections and defects
      5.4 Hardness
           5.4.1 Hardness
           5.4.2 Hardness tolerance
      5.5 Tensile strength and elongation at break
      5.6 Compression set in air
           5.6.1 General
           5.6.2 Compression set at 70 degree C
           5.6.3 Compression set at low temperature (-25
                 degree C)
      5.7 Accelerated ageing in air
      5.8 Stress relaxation in compression
      5.9 Recovery at low and high temperatures (-25 degree C,
           +70 degree C)
      5.10 Ozone resistance
      5.11 Protection against over-extension
      5.12 Function testing for cold climate areas
      5.13 Dangerous substances
    6 Evaluation of conformity
      6.1 General
      6.2 Type testing
           6.2.1 Initial Type Testing
           6.2.2 Further type testing
      6.3 Factory Production Control (FPC)
           6.3.1 General
           6.3.2 Frequency of testing
           6.3.3 Equipment
           6.3.4 Raw materials and components
           6.3.5 Design process
           6.3.6 Non-conforming products
    7 Marking, labelling and packaging
    Annex A (normative) Initial Type Testing and frequencies of
                           testing for Factory Production Control
    Annex B (informative) Example of a product data sheet
      B.1 General information
    Annex C (informative) Installation
    Annex ZA (informative) Clauses of this European Standard
                           addressing essential requirements or
                           other provisions of EU Directives
      ZA.1 Scope and relevant characteristics
      ZA.2 Procedure(s) for attestation of conformity
      ZA.3 CE marking and labelling
    Bibliography

    Abstract - (Show below) - (Hide below)

    Specifies requirements for preformed joint seals made of vulcanised rubber for concrete pavements.

    General Product Information - (Show below) - (Hide below)

    Committee B/510/3
    Development Note Supersedes 03/118041 DC (03/2006)
    Document Type Standard
    Publisher British Standards Institution
    Status Current
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    08/30043515 DC : DRAFT FEB 2008 BS 5385-1 - WALL AND FLOOR TILING - PART 1: DESIGN AND INSTALLATION OF CERAMIC AND NATURAL STONE AND MOSAIC WALL TILING IN NORMAL INTERNAL CONDITIONS - CODE OF PRACTICE
    BS 5385-3(2014) : 2014 WALL AND FLOOR TILING - PART 3: DESIGN AND INSTALLATION OF INTERNAL AND EXTERNAL CERAMIC AND MOSAIC FLOOR TILING IN NORMAL CONDITIONS - CODE OF PRACTICE
    14/30283603 DC : 0 BS 5385-3 - WALL AND FLOOR TILING - PART 3: DESIGN AND INSTALLATION OF INTERNAL ANDEXTERNAL CERAMIC AND MOSAIC FLOOR TILING IN NORMAL CONDITIONS - CODE OF PRACTICE

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 14840 : 2005 JOINT FILLERS AND SEALANTS - TEST METHODS FOR PREFORMED JOINT SEALS
    89/106/EEC : 1988 COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS
    ISO 188:2011 Rubber, vulcanized or thermoplastic Accelerated ageing and heat resistance tests
    ISO 2285:2013 Rubber, vulcanized or thermoplastic Determination of tension set under constant elongation, and of tension set, elongation and creep under constant tensile load
    ISO 1431-1:2012 Rubber, vulcanized or thermoplastic Resistance to ozone cracking Part 1: Static and dynamic strain testing
    ISO 3302-1:2014 Rubber Tolerances for products Part 1: Dimensional tolerances
    EN ISO 9001:2015 QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS (ISO 9001:2015)
    ISO 3384:2005 Rubber, vulcanized or thermoplastic Determination of stress relaxation in compression at ambient and at elevated temperatures
    ISO 9001:2015 Quality management systems - Requirements
    ISO 5893:2002 Rubber and plastics test equipment Tensile, flexural and compression types (constant rate of traverse) Specification
    ISO 37:2017 Rubber, vulcanized or thermoplastic Determination of tensile stress-strain properties
    ISO 48:2010 Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective