• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

BS EN 14753:2007

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Safety of machinery. Safety requirements for machinery and equipment for continuous casting of steel
Available format(s)

Hardcopy , PDF

Superseded date

15-08-2022

Language(s)

English

Published date

30-05-2008

This European Standard applies for plant (containing machinery and equipment) used in the process of continuous casting of liquid steel (hereafter referred to as continuous casting machine, CCM) as defined in 3.1 and illustrated in Annex B. This European Standard deals with all significant hazards, hazardous situations and events relevant to machinery and equipment for the continuous casting of steel, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This European Standard specifies the safety requirements to be met during design, assembly, transport, commissioning, operation, maintenance (as described in Clause 5) and decommissioning of the equipment. This European Standard assumes that the machinery and equipment of the plant is operated and maintained by adequately trained and competent personnel (see 7.4). Manual intervention for setting, adjustment and maintenance is accepted as part of the intended use of the plant. This European Standard assumes that the machinery is used with adequate workplace lighting conforming to EN 12464-1. NOTE Local regulations regarding lighting should be considered and could differ from requirements of EN 12464-1. This European Standard applies to: CCM for the transformation of molten liquid steel into solid products in sections (e.g. square, rectangular, beam blank, circular) ? from the point where overhead cranes or other transport systems deposit ladles (e.g. in a ladle turret or ladle car); via casting process; via cutting equipment; to the run-out-area where the cut product is collected. This European Standard does not cover safety requirements for: auxiliary plants (e.g. water treatment, refractory handling); ladles; cranes; winches and hoists; conveyors or handling systems. This European Standard is not applicable to CCM, manufactured before the date of publication of this standard by CEN.

Committee
MCE/23
DevelopmentNote
Supersedes 03/313810 DC. (05/2008)
DocumentType
Standard
Pages
50
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
EN 14753:2007 Identical

EN 294:1992/AC:1993 SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE UPPER LIMBS
ISO 11202:2010 Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections
EN 894-3:2000+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators
EN 12464-1:2011 Light and lighting - Lighting of work places - Part 1: Indoor work places
EN 982:1996+A1:2008 Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics
ISO 4871:1996 Acoustics — Declaration and verification of noise emission values of machinery and equipment
EN 1037:1995+A1:2008 Safety of machinery - Prevention of unexpected start-up
ISO 14122-3:2016 Safety of machinery — Permanent means of access to machinery — Part 3: Stairs, stepladders and guard-rails
PREN 15004-1 : DRAFT 2016 FIXED FIREFIGHTING SYSTEMS - GAS EXTINGUISHING SYSTEMS - PART 1: DESIGN, INSTALLATION AND MAINTENANCE (ISO 14520-1:2015, MODIFIED)
ISO 14122-1:2016 Safety of machinery — Permanent means of access to machinery — Part 1: Choice of fixed means and general requirements of access
EN 1088:1995+A2:2008 Safety of machinery - Interlocking devices associated with guards - Principles for design and selection
IEC 61310-2:2007 Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking
EN 981:1996+A1:2008 Safety of machinery - System of auditory and visual danger and information signals
ISO/TR 11688-1:1995 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning
ISO 5598:2008 Fluid power systems and components Vocabulary
EN 61310-2:2008 Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking
EN 12094-1:2003 Fixed firefighting systems - Components for gas extinguishing systems - Part 1: Requirements and test methods for electrical automatic control and delay devices
ISO 13732-1:2006 Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces
EN 614-2:2000+A1:2008 Safety of machinery - Ergonomic design principles - Part 2: Interactions between the design of machinery and work tasks
EN 1837:1999+A1:2009 Safety of machinery - Integral lighting of machines
EN 811 : 1996 SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE LOWER LIMBS
EN 349:1993+A1:2008 Safety of machinery - Minimum gaps to avoid crushing of parts of the human body
EN 13478:2001+A1:2008 Safety of machinery - Fire prevention and protection
IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
EN ISO 13850:2015 Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015)
EN 1050 : 1996 SAFETY OF MACHINERY - PRINCIPLES FOR RISK ASSESSMENT
EN ISO 7731:2008 Ergonomics - Danger signals for public and work areas - Auditory danger signals (ISO 7731:2003)
EN ISO 11820 : 1996 ACOUSTICS - MEASUREMENTS ON SILENCERS IN SITU
EN 614-1:2006+A1:2009 Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles
EN ISO 11688-2 : 2000 ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 2: INTRODUCTION TO THE PHYSICS OF LOW-NOISE DESIGN
ISO 14122-4:2016 Safety of machinery — Permanent means of access to machinery — Part 4: Fixed ladders
ISO 7731:2003 Ergonomics Danger signals for public and work areas Auditory danger signals
EN 574:1996+A1:2008 Safety of machinery - Two-hand control devices - Functional aspects - Principles for design
EN ISO 13732-1:2008 Ergonomics of the thermal environment - Methods for the assessment of human responses to contact with surfaces - Part 1: Hot surfaces (ISO 13732-1:2006)
ISO 11820:1996 Acoustics — Measurements on silencers in situ
EN 626-2:1996+A1:2008 Safety of machinery - Reduction of risk to health from hazardous substances emitted by machinery - Part 2: Methodology leading to verification procedures
IEC 60405:2003 Nuclear instrumentation - Constructional requirements and classification of radiometric gauges
EN ISO 12100-1:2003/A1:2009 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY
EN ISO 14122-3:2016 Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2016)
EN 953:1997+A1:2009 Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards
EN 842:1996+A1:2008 Safety of machinery - Visual danger signals - General requirements, design and testing
EN ISO 14122-4:2016 Safety of machinery - Permanent means of access to machinery - Part 4: Fixed ladders (ISO 14122-4:2016)
EN ISO 14122-2:2016 Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways (ISO 14122-2:2016)
ISO 12100-2:2003 Safety of machinery Basic concepts, general principles for design Part 2: Technical principles
EN ISO 12100-2:2003/A1:2009 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES
EN ISO 6682:2008 Earth-moving machinery - Zones of comfort and reach for controls (ISO 6682:1986, including Amd 1:1989)
ISO 14520-1:2015 Gaseous fire-extinguishing systems — Physical properties and system design — Part 1: General requirements
EN 983:1996+A1:2008 Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics
ISO 11064-1:2000 Ergonomic design of control centres Part 1: Principles for the design of control centres
EN ISO 6743-4:2015 Lubricants, industrial oils and related products (class L) - Classification - Part 4: Family H (Hydraulic systems) (ISO 6743-4:2015)
ISO 12100-1:2003 Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology
EN ISO 13849-1:2015 Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015)
ISO 13850:2015 Safety of machinery Emergency stop function Principles for design
EN ISO 4871:2009 Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)
ISO 11546-1:1995 Acoustics Determination of sound insulation performances of enclosures Part 1: Measurements under laboratory conditions (for declaration purposes)
IEC 61310-1:2007 Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals
EN 50171 : 2001 COR 2001 CENTRAL POWER SUPPLY SYSTEMS
EN 626-1:1994+A1:2008 Safety of machinery - Reduction of risks to health from hazardous substances emitted by machinery - Part 1: Principles and specifications for machinery manufacturers
EN ISO 11064-1:2000 Ergonomic design of control centres - Part 1: Principles for the design of control centres (ISO 11064-1:2000)
EN ISO 11691:2009 Acoustics - Measurement of insertion loss of ducted silencers without flow - Laboratory survey method (ISO 11691:1995)
EN ISO 11821 : 1997 ACOUSTICS - MEASUREMENT OF THE IN SITU SOUND ATTENUATION OF A REMOVABLE SCREEN
ISO 7000:2014 Graphical symbols for use on equipment Registered symbols
EN ISO 11546-1:2009 Acoustics - Determination of sound insulation performances of enclosures - Part 1: Measurements under laboratory conditions (for declaration purposes) (ISO 11546-1:1995)
1998/37/EC : 1998 DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 22 JUNE 1998 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO MACHINERY
ISO 14122-2:2016 Safety of machinery — Permanent means of access to machinery — Part 2: Working platforms and walkways
EN ISO 11688-1:2009 Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995)
EN ISO 14122-1:2016 Safety of machinery - Permanent means of access to machinery - Part 1: Choice of fixed means and general requirements of access (ISO 14122-1:2016)
ISO 13849-1:2015 Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design
ISO/TR 11688-2:1998 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design
EN 61310-1:2008 Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals
EN ISO 11202:2010 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010)
ISO 11691:1995 Acoustics Measurement of insertion loss of ducted silencers without flow Laboratory survey method
ISO 6743-4:2015 Lubricants, industrial oils and related products (class L) Classification Part 4: Family H (Hydraulic systems)
ISO 7745:2010 Hydraulic fluid power — Fire-resistant (FR) fluids — Requirements and guidelines for use
ISO 11821:1997 Acoustics — Measurement of the in situ sound attenuation of a removable screen
EN 60204-1 : 2006 COR 2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS

View more information
£246.00
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.