BS EN 60950-22:2017

Superseded

View Superseded by

Information technology equipment. Safety Equipment to be installed outdoors

Available format(s)

Hardcopy , PDF

Superseded date

23-03-2020

Language(s)

English

Published date

08-08-2017

Publisher

British Standards Institution

1.1 Equipment covered This part of IEC60950 applies to information technology equipment intended to be installed in an outdoor location. The requirements for outdoor equipment also apply, where relevant, to outdoor enclosures suitable for direct installation in the field and supplied for housing information technology equipment to be installed in an outdoor location. 1.2 Additional requirements Each installation may have particular requirements. Some examples are given in 4.2. In addition, requirements for protection of the outdoor equipment against the effects of direct lightning strikes are not covered by the standard. For information on this subject, see IEC62305‑1 .

Committee	EPL/108
DevelopmentNote	Supersedes 03/103069 DC (06/2006) Supersedes 15/30297966 DC. (08/2017)
DocumentType	Standard
ISBN	9780580859779
Pages	40
PublisherName	British Standards Institution
Status	Superseded
SupersededBy	BS EN IEC 62368-1:2020+A11:2020
Supersedes	15/30297966 DC : 0 03/103069 DC : DRAFT JAN 2003 BS EN 60950-22:2006

Standards	Relationship
EN 60060-1:2010	Identical
DIN EN 60950-22 : 2017	Identical
NBN EN 60950-22 : 2006 AMD 1 2010	Identical
I.S. EN 60950-22:2017	Identical
IEC 60950-22:2016	Identical
NF EN 60950-22 : 2017	Identical
UNE-EN 60950-22:2006	Identical
EN 60950-22:2017	Identical
SN EN 60950-22 : 2017	Identical

IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV	Information technology equipment - Safety - Part 1: General requirements
ISO 4892-1:2016	Plastics Methods of exposure to laboratory light sources Part 1: General guidance
IEC 60364-4-43:2008	Low-voltage electrical installations - Part 4-43: Protection for safety - Protection against overcurrent
EN ISO 8256:2004	Plastics - Determination of tensile-impact strength (ISO 8256:2004)
EN 62368-1:2014/AC:2017-03	AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS (IEC 62368-1:2014, MODIFIED)
EN ISO 180:2000/A2:2013	PLASTICS - DETERMINATION OF IZOD IMPACT STRENGTH (ISO 180:2000/AMD 2:2013)
EN ISO 4892-1:2016	Plastics - Methods of exposure to laboratory light sources - Part 1: General guidance (ISO 4892-1:2016)
EN ISO 3231:1997	Paints and varnishes - Determination of resistance to humid atmospheres containing sulfur dioxide (ISO 3231:1993)
IEC 61587-1:2016	Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 1: Environmental requirements, test set-up and safety aspects for cabinets, racks, subracks and chassis under indoor condition use and transportation
IEC 60896-21:2004	Stationary lead-acid batteries - Part 21: Valve regulated types - Methods of test
IEC 60364-5-53:2001+AMD1:2002+AMD2:2015 CSV	Electrical installations of buildings - Part 5-53: Selection and erection of electrical equipment - Isolation, switching and control
EN 60950-1:2006/A2:2013	INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60950-1:2005/A2:2013, MODIFIED)
IEC 60068-2-11:1981	Basic environmental testing procedures - Part 2-11: Tests - Test Ka: Salt mist
EN ISO 178:2010/A1:2013	PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010/AMD 1:2013)
ISO 8256:2004	Plastics — Determination of tensile-impact strength
ISO 14993:2001	Corrosion of metals and alloys Accelerated testing involving cyclic exposure to salt mist, "dry" and "wet" conditions
IEC 62305-1:2010	Protection against lightning - Part 1: General principles
ISO 4628-3:2016	Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 3: Assessment of degree of rusting
ISO 21207:2015	Corrosion tests in artificial atmospheres — Accelerated corrosion tests involving alternate exposure to corrosion-promoting gases, neutral salt-spray and drying
ISO 180:2000	Plastics Determination of Izod impact strength
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV	Degrees of protection provided by enclosures (IP Code)
IEC 60896-22:2004	Stationary lead-acid batteries - Part 22: Valve regulated types - Requirements
ISO/TS 18173:2005	Non-destructive testing General terms and definitions
IEC 61643-11:2011	Low-voltage surge protective devices - Part 11: Surge protective devices connected to low-voltage power systems - Requirements and test methods
IEC 61969-3:2011	Mechanical structures for electronic equipment - Outdoor enclosures - Part 3: Environmental requirements, tests and safety aspects
ISO 4892-4:2013	Plastics — Methods of exposure to laboratory light sources — Part 4: Open-flame carbon-arc lamps
IEC 61439-5:2014	Low-voltage switchgear and controlgear assemblies - Part 5: Assemblies for power distribution in public networks
ISO 4892-2:2013	Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
EN 60068-2-11:1999	Environmental testing - Part 2: Tests - Test Ka: Salt mist
EN 60529:1991/AC:2016-12	DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
ISO 178:2010	Plastics Determination of flexural properties
ASTM D 471 : 2016-02	TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS
IEC 60664-1:2007	Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
EN ISO 4892-2:2013	Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon-arc lamps (ISO 4892-2:2013)
IEC 62368-1:2014	Audio/video, information and communication technology equipment - Part 1: Safety requirements
IEC 62485-2:2010	Safety requirements for secondary batteries and battery installations - Part 2: Stationary batteries
ISO 3231:1993	Paints and varnishes — Determination of resistance to humid atmospheres containing sulfur dioxide