• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

BS EN 61038:1993

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Specification for time switches for tariff and load control
Available format(s)

Hardcopy , PDF

Superseded date

21-01-2005

Language(s)

English

Published date

15-02-2000

Committees responsible
National foreword
Foreword
1 Scope
2 Normative references
3 Definitions
4 Requirements
5 Tests and test conditions
Annex A (normative) Relationship between ambient air
                    temperature and relative humidity
Annex B (normative) Reference and limiting values of the
                    influence quantities
Annex C (normative) Electromagnet for testing the
                    influence of externally produced
                    magnetic field
Annex D (informative) Acceptance tests
Annex ZA (normative) Other international publications quoted
                     in this standard with the references
                     of the relevant European publications
Table 1 - Clearances and creepage distances for the terminal
          block
Table 2 - Temperature range
Table 3 - Relative humidity
Table 4 - Voltage range
Table 5 - Rated breaking voltages
Table 6 - Rated breaking current
Table 7 - Maximum inaccuracies

Requirements for time switches used for indoor application to control electrical loads, multi-tariff registers and max. demand devices. The switches may employ electronic circuits but exclude switches operated by remote control.

Committee
PEL/13
DevelopmentNote
Renumbers and supersedes BS 7415(1991). 1993 version incorporates amendment 7674 to BS 7415(1991). Supersedes 86/20620 DC. (12/2005)
DocumentType
Standard
Pages
28
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

BS EN 55022:2010 Information technology equipment. Radio disturbance characteristics. Limits and methods of measurement
BS 7003:1988 Specification for spring-operated impact-test apparatus and its calibration
IEC 61000-4-4 : 3.0EN+(REDLINE+VERSION) ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-4: TESTING AND MEASUREMENT TECHNIQUES - ELECTRICAL FAST TRANSIENT/BURST IMMUNITY TEST
IEC 60068-2-27:2008 Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
BS 2011-2.1B:1977 Environmental testing. Tests Tests B. Dry Heat
ISO 75:1987 Plastics and ebonite Determination of temperature of deflection under load
IEC 61000-4-4:2012 RLV Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement techniques - Electrical fast transient/burst immunity test
BS 6001-1(1999) : 1999 SAMPLING PROCEDURES FOR INSPECTION BY ATTRIBUTES - PART 1: SAMPLING SCHEMES INDEXED BY ACCEPTANCE QUALITY LIMIT (AQL) FOR LOT-BY-LOT INSPECTION
IEC 60695-2-11:2014 Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT)
BS EN 61000-4-2:2009 Electromagnetic compatibility (EMC) Testing and measurement techniques. Electrostatic discharge immunity test
BS 6458-2.1:1984 Fire hazard testing for electrotechnical products. Test methods Glow-wire test
IEC 60817:1984 Spring-operated impact-test apparatus and its calibration
CISPR 22:2008 Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement
IEC 60085:2007 Electrical insulation - Thermal evaluation and designation
IEC 60410:1973 Sampling plans and procedures for inspection by attributes
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
IEC 60269-3:2010+AMD1:2013 CSV Low-voltage fuses - Part 3: Supplementary requirements for fuses foruse by unskilled persons (fuses mainly for household or similar applications) - Examples of standardized systems of fuses A to F
IEC 60417-2:1998 Graphical symbols for use on equipment - Part 2: Symbol originals
IEC 60068-2-2:2007 Environmental testing - Part 2-2: Tests - Test B: Dry heat
IEC 61000-4-2:2008 Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test
IEC 61000-4-3:2006+AMD1:2007+AMD2:2010 CSV Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test
BS 923:1972 Guide on high-voltage testing techniques.
IEC 60721-3-3:1994+AMD1:1995+AMD2:1996 CSV Classification of environmental conditions - Part 3-3: Classification of groups of environmental parameters and their severities - Stationary use at weatherprotected locations
IEC 60068-2-1:2007 Environmental testing - Part 2-1: Tests - Test A: Cold
BS 6217:1981 Guide to graphical symbols for use on electrical equipment
IEC 60068-2-30:2005 Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)

View more information
£198.00
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.