We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • BS EN 61514-2 : 2013

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    INDUSTRIAL PROCESS CONTROL SYSTEMS - PART 2: METHODS OF EVALUATING THE PERFORMANCE OF INTELLIGENT VALVE POSITIONERS WITH PNEUMATIC OUTPUTS MOUNTED ON AN ACTUATOR VALVE ASSEMBLY

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2013

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Design review
    5 Performance testing
    6 Other considerations
    7 Evaluation report
    Annex A (normative) - Vibration test set-up
    Bibliography
    Annex ZA (normative) - Normative references to
             international publications with their
             corresponding European publications

    Abstract - (Show below) - (Hide below)

    Describes design reviews and tests intended to measure and determine the static and dynamic performance, the degree of intelligence and the communication capabilities of single-acting or double-acting intelligent valve positioners.

    General Product Information - (Show below) - (Hide below)

    Committee GEL/65/1
    Development Note To be read in conjunction with BS EN 61514. Supersedes 02/203205 DC. (05/2004)
    Document Type Standard
    Publisher British Standards Institution
    Status Current
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 61298-1:2008 PROCESS MEASUREMENT AND CONTROL DEVICES - GENERAL METHODS AND PROCEDURES FOR EVALUATING PERFORMANCE - PART 1: GENERAL CONSIDERATIONS
    EN 61514 : 2002 INDUSTRIAL-PROCESS CONTROL SYSTEMS - METHODS OF EVALUATING THE PERFORMANCE OF VALVE POSITIONERS WITH PNEUMATIC OUTPUTS
    IEC 61298-1:2008 Process measurement and control devices - General methods and procedures for evaluating performance - Part 1: General considerations
    EN 60534-1:2005 INDUSTRIAL-PROCESS CONTROL VALVES - PART 1: CONTROL VALVE TERMINOLOGY AND GENERAL CONSIDERATIONS
    EN 61298-3:2008 PROCESS MEASUREMENT AND CONTROL DEVICES - GENERAL METHODS AND PROCEDURES FOR EVALUATING PERFORMANCE - PART 3: TESTS FOR THE EFFECTS OF INFLUENCE QUANTITIES
    IEC 61298-2:2008 Process measurement and control devices - General methods and procedures for evaluating performance - Part 2: Tests under reference conditions
    EN 61298-2:2008 PROCESS MEASUREMENT AND CONTROL DEVICES - GENERAL METHODS AND PROCEDURES FOR EVALUATING PERFORMANCE - PART 2: TESTS UNDER REFERENCE CONDITIONS
    EN 61000-4-11:2004/A1:2017 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-11: TESTING AND MEASUREMENT TECHNIQUES - VOLTAGE DIPS, SHORT INTERRUPTIONS AND VOLTAGE VARIATIONS IMMUNITY TESTS (IEC 61000-4-11:2004/A1:2017)
    EN 61298-4:2008 PROCESS MEASUREMENT AND CONTROL DEVICES - GENERAL METHODS AND PROCEDURES FOR EVALUATING PERFORMANCE - PART 4: EVALUATION REPORT CONTENT
    EN 60068-2-1:2007 ENVIRONMENTAL TESTING - PART 2-1: TESTS - TEST A: COLD
    EN 60068-2-2:2007 ENVIRONMENTAL TESTING - PART 2-2: TESTS - TEST B: DRY HEAT
    IEC 61000-4-11:2004+AMD1:2017 CSV Electromagnetic compatibility (EMC) - Part 4-11: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests
    IEC 60068-2-31:2008 ENVIRONMENTAL TESTING - PART 2-31: TESTS - TEST EC: ROUGH HANDLING SHOCKS, PRIMARILY FOR EQUIPMENT-TYPE SPECIMENS
    EN 61326-1:2013 ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL AND LABORATORY USE - EMC REQUIREMENTS - PART 1: GENERAL REQUIREMENTS (IEC 61326-1:2012)
    MIL HDBK 217 : F RELIABILITY PREDICTION OF ELECTRONIC EQUIPMENT
    IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
    EN 55011:2016/A1:2017 INDUSTRIAL, SCIENTIFIC AND MEDICAL EQUIPMENT - RADIO-FREQUENCY DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT (CISPR 11:2015/A1:2016)
    IEC 61298-3:2008 Process measurement and control devices - General methods and procedures for evaluating performance - Part 3: Tests for the effects of influence quantities
    IEC 60068-2-2:2007 Environmental testing - Part 2-2: Tests - Test B: Dry heat
    EN 61032 : 1998 PROTECTION OF PERSONS AND EQUIPMENT BY ENCLOSURES - PROBES FOR VERIFICATION (IEC 61032:1997)
    EN 60068-2-78:2013 ENVIRONMENTAL TESTING - PART 2-78: TESTS - TEST CAB: DAMP HEAT, STEADY STATE (IEC 60068-2-78:2012)
    IEC TS 62098:2000 Evaluation methods for microprocessor- based instruments
    IEC 61298-4:2008 Process measurement and control devices - General methods and procedures for evaluating performance - Part 4: Evaluation report content
    EN 60068-2-6:2008 ENVIRONMENTAL TESTING - PART 2-6: TESTS - TEST FC: VIBRATION (SINUSOIDAL)
    CISPR 11:2015 RLV Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement
    IEC 60068-2-1:2007 Environmental testing - Part 2-1: Tests - Test A: Cold
    IEC 61514:2000 Industrial-process control systems - Methods of evaluating the performance of valve positioners with pneumatic outputs
    EN 61010-1:2010 SAFETY REQUIREMENTS FOR ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL AND LABORATORY USE - PART 1: GENERAL REQUIREMENTS (IEC 61010-1:2010)
    EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
    IEC 61032:1997 Protection of persons and equipment by enclosures - Probes for verification
    IEC 61010-1:2010+AMD1:2016 CSV Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements
    IEC 60534-1:2005 Industrial-process control valves - Part 1: Control valve terminology and general considerations
    EN 60068-2-31:2008 ENVIRONMENTAL TESTING - PART 2-31: TESTS - TEST EC: ROUGH HANDLING SHOCKS, PRIMARILY FOR EQUIPMENT-TYPE SPECIMENS
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective