We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • BS EN ISO 178 : 2010

    Withdrawn A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES

    Available format(s):  Hardcopy, PDF

    Withdrawn date:  16-05-2019

    Language(s):  English

    Published date:  01-01-2010

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Principle
    5 Test machine
    6 Test specimens
    7 Atmosphere for conditioning and testing
    8 Procedure
    9 Calculation and expression of results
    10 Precision
    11 Test report
    Annex A (informative) - Precision statement
    Annex B (informative) - Influence of changes in test
            speed on the measured values of flexural
            properties
    Bibliography

    Abstract - (Show below) - (Hide below)

    Defines a method for determining the flexural properties of rigid and semi-rigid plastics under defined conditions.

    General Product Information - (Show below) - (Hide below)

    Committee PRI/21
    Development Note Supersedes 99/121897 DC (03/2003) Supersedes and renumbers BS 2782-3.335A(1993) (07/2004) Supersedes 08/30188330 DC. (01/2011) 2010 Edition Re-Issued in July 2013 & incorporates AMD 1 2013. Supersedes 12/30255171 DC. (07/2013)
    Document Type Standard
    Publisher British Standards Institution
    Status Withdrawn
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS 8499:2017 Specification for domestic gas meter boxes and meter bracket
    BS EN 1993-1-11 NA : 2006 UK NATIONAL ANNEX TO EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-11: DESIGN OF STRUCTURES WITH TENSION COMPONENTS
    11/30240637 DC : 0 BS 8567 - SPECIFICATION FOR OUTDOOR ELECTRICITY METER CUPBOARDS
    BS 8567(2012) : 2012 SPECIFICATION FOR OUTDOOR ELECTRICITY METER CUPBOARDS
    BS 8499:2009 SPECIFICATION FOR DOMESTIC GAS METER BOXES AND METER BRACKET
    08/30128144 DC : DRAFT APR 2008 BS EN 1993-1-11 - UK NATIONAL ANNEX TO EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 1-11: DESIGN OF STRUCTURES WITH TENSION COMPONENTS
    BS 8472(2011) : 2011 METHODS FOR THE ASSESSMENT OF THE OXO-BIODEGRADATION OF PLASTICS AND OF THE PHYTO-TOXICITY OF THE RESIDUES IN CONTROLLED LABORATORY CONDITIONS
    DEFSTAN 80-157/2(2004) : 2004 EPOXIDE RESIN PUTTY SYSTEM
    09/30160438 DC : DRAFT JAN 2009 BS 8499 - SPECIFICATION FOR DOMESTIC GAS METER BOXES AND METER BRACKET

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 10350-2:2011 Plastics Acquisition and presentation of comparable single-point data Part 2: Long-fibre-reinforced plastics
    ISO 293:2004 Plastics Compression moulding of test specimens of thermoplastic materials
    ISO 23529:2016 Rubber General procedures for preparing and conditioning test pieces for physical test methods
    ISO 295:2004 Plastics — Compression moulding of test specimens of thermosetting materials
    ISO 10350-1:2017 Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials
    ISO 10724-1:1998 Plastics Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) Part 1: General principles and moulding of multipurpose test specimens
    ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
    ISO 9513:2012 Metallic materials — Calibration of extensometer systems used in uniaxial testing
    ISO 2602:1980 Statistical interpretation of test results Estimation of the mean Confidence interval
    ISO 1209-2:2007 Rigid cellular plastics Determination of flexural properties Part 2: Determination of flexural strength and apparent flexural modulus of elasticity
    ISO 472:2013 Plastics Vocabulary
    ISO 291:2008 Plastics Standard atmospheres for conditioning and testing
    ISO 14125:1998 Fibre-reinforced plastic composites Determination of flexural properties
    ISO 294-1:2017 Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens
    ISO 7500-1:2015 Metallic materials Calibration and verification of static uniaxial testing machines Part 1: Tension/compression testing machines Calibration and verification of the force-measuring system
    ISO 2818:1994 Plastics Preparation of test specimens by machining
    ISO 20753:2008 Plastics Test specimens
    ISO 16012:2015 Plastics Determination of linear dimensions of test specimens
    ISO 1209-1:2007 Rigid cellular plastics Determination of flexural properties Part 1: Basic bending test
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective