We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • BS EN ISO 1873-1 : 1995

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    PLASTICS - POLYPROPYLENE (PP) MOULDING AND EXTRUSION MATERIALS - DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS

    Available format(s):  Hardcopy, PDF

    Superseded date:  31-03-2015

    Language(s):  English

    Published date:  01-01-1995

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Committees responsible
    National foreword
    Foreword
    Specification
    1 Scope
    2 Normative References
    3 Design and specification system
    4 Examples of designations
    Tables
    1 Code-letters used for additional information in data
        block 1
    2 Code-letters used in data block 2
    3 Ranges of tensile modulus of elasticity in data
        block 3
    4 Ranges of notched Charpy impact strength in data
        block 3
    5 Range of melt mass-flow rate in data block 3
    6 Code-letters for fillers and reinforcing materials
        in data block 4

    Abstract - (Show below) - (Hide below)

    Establishes a system of designation for polypropylene (PP) thermoplastic material that may be used as the basis for specifications. Applies to all propylene homopolymers and to copolymers of propylene with a content of other 1-olefins of less than 50% (m/m), as well as blends of polymers containing at least 50% (m/m) of aforementioned polymers.

    General Product Information - (Show below) - (Hide below)

    Committee PRI/82
    Development Note Supersedes 94/340139 DC. (09/2005)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS 8297(2000) : 2000 CODE OF PRACTICE FOR DESIGN AND INSTALLATION OF NON-LOADBEARING PRECAST CONCRETE CLADDING
    BS 8297:2000 CODE OF PRACTICE FOR DESIGN AND INSTALLATION OF NON-LOADBEARING PRECAST CONCRETE CLADDING

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 1873-2:2007 Plastics Polypropylene (PP) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
    BS 2782-3.359(1993) : 1993 AMD 8643 METHODS OF TESTING PLASTICS - MECHANICAL PROPERTIES - DETERMINATION OF CHARPY IMPACT STRENGTH
    BS 2782-3.321(1994) : 1994 AMD 8633 PLASTICS - DETERMINATION OF TENSILE PROPERTIES - GENERAL PRINCIPLES
    BS 2782-7.720A(1997) : 1997 AMD 10722 METHODS OF TESTING PLASTICS - RHEOLOGICAL PROPERTIES - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND THE MELT VOLUME-FLOW RATE (MVR) OF THERMOPLASTICS
    BS 2782-3.322(1994) : 1994 AMD 8639 PLASTICS - DETERMINATION OF TENSILE PROPERTIES - TEST CONDITIONS FOR MOULDING AND EXTRUSION PLASTICS
    ISO 1043-2:2011 Plastics Symbols and abbreviated terms Part 2: Fillers and reinforcing materials
    ISO 1043-1:2011 Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective