• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

BS EN ISO 3269:2001

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Fasteners. Acceptance inspection
Available format(s)

Hardcopy , PDF

Superseded date

15-10-2019

Language(s)

English

Published date

15-07-2001

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and conditions
4 General principles and requirements
5 Acceptance inspection procedure for fastener
   characteristics
Annex A (informative) Recommendations for acceptance-
   inspection procedures (for example, for dimensional
   characteristics)
Annex B (informative) Guidance and explanation
   concerning the principle of this international
   standard
Bibliography

Gives the procedure to be followed by the purchaser at his acceptance inspection so as to decide whether a lot of fasteners may be accepted or rejected, when another acceptance procedure has not been agreed.

Committee
FME/9
DevelopmentNote
Supersedes 97/713351 DC (06/2005) Reviewed and confirmed by BSI, January 2007. (12/2006)
DocumentType
Standard
Pages
30
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

BS 4933:2010 Specification for ISO metric black cup and countersunk head bolts and screws with hexagon nuts
BS 7419:2012 Specification for holding down bolts
12/30258706 DC : 0 BS 7419 - SPECIFICATION FOR HOLDING DOWN BOLTS

ISO 8839:1986 Mechanical properties of fasteners Bolts, screws, studs and nuts made of non-ferrous metals
ISO 898-2:2012 Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread
ISO 10683:2014 Fasteners Non-electrolytically applied zinc flake coatings
EN 26157-3 : 1991 FASTENERS - SURFACE DISCONTINUITIES - PART 3: BOLTS, SCREWS AND STUDS FOR SPECIAL REQUIREMENTS (ISO 6157-3:1988)
ISO 4759-3:2016 Tolerances for fasteners Part 3: Washers for bolts, screws and nuts Product grades A, C and F
ISO 4042:1999 Fasteners Electroplated coatings
ISO 3506-1:2009 Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs
ISO 6157-3:1988 Fasteners Surface discontinuities Part 3: Bolts, screws and studs for special requirements
EN ISO 4042:1999 FASTENERS - ELECTROPLATED COATINGS (ISO 4042:1999)
EN ISO 3506-1:2009 Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:2009)
EN ISO 3506-3:2009 Mechanical properties of corrosion-resistant stainless steel fasteners - Part 3: Set screws and similar fasteners not under tensile stress (ISO 3506-3:2009)
ISO 4759-1:2000 Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C
ISO 6157-1:1988 Fasteners — Surface discontinuities — Part 1: Bolts, screws and studs for general requirements
EN 26157-1 : 1991 FASTENERS - SURFACE DISCONTINUITIES - PART 1: BOLTS, SCREWS AND STUDS FOR GENERAL REQUIREMENTS
ISO 2320:2015 Fasteners Prevailing torque steel nuts Functional properties
EN ISO 4759-3:2016 Tolerances for fasteners - Part 3: Washers for bolts, screws and nuts - Product grades A, C and F (ISO 4759-3:2016)
ISO 7085:1999 Mechanical and performance requirements of case hardened and tempered metric thread rolling screws
ISO 8402:1994 Quality management and quality assurance — Vocabulary
EN 20898-2 : 1993 MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992)
ISO 1502:1996 ISO general-purpose metric screw threads Gauges and gauging
ISO 898-6:1994 Mechanical properties of fasteners Part 6: Nuts with specified proof load values Fine pitch thread
ISO 898-5:2012 Mechanical properties of fasteners made of carbon steel and alloy steel Part 5: Set screws and similar threaded fasteners with specified hardness classes Coarse thread and fine pitch thread
ISO 3506-3:2009 Mechanical properties of corrosion-resistant stainless steel fasteners Part 3: Set screws and similar fasteners not under tensile stress
EN ISO 2702:2011 Heat-treated steel tapping screws - Mechanical properties (ISO 2702:2011)
ISO 3534-2:2006 Statistics Vocabulary and symbols Part 2: Applied statistics
EN ISO 898-5:2012 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 5: Set screws and similar threaded fasteners with specified hardness classes - Coarse thread and fine pitch thread (ISO 898-5:2012)
EN ISO 2320:2015 Fasteners - Prevailing torque steel nuts - Functional properties (ISO 2320:2015)
EN ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013)
ISO 6157-2:1995 Fasteners Surface discontinuities Part 2: Nuts
EN ISO 898-6 : 1995 MECHANICAL PROPERTIES OF FASTENERS - PART 6: NUTS WITH SPECIFIED PROOF LOAD VALUES - FINE PITCH THREAD
ISO 8992:2005 Fasteners — General requirements for bolts, screws, studs and nuts
ISO 2702:2011 Heat-treated steel tapping screws — Mechanical properties
ISO 1478:1999 Tapping screws thread
ISO 3506-2:2009 Mechanical properties of corrosion-resistant stainless steel fasteners Part 2: Nuts
ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread
EN ISO 3506-2:2009 Mechanical properties of corrosion-resistant stainless steel fasteners - Part 2: Nuts (ISO 3506-2:2009)

View more information
£198.00
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.