|
ISO 25780:2011
|
Plastics piping systems for pressure and non-pressure water supply, irrigation, drainage or sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin — Pipes with flexible joints intended to be installed using jacking techniques
|
|
ISO 8521:2009
|
Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Test methods for the determination of the apparent initial circumferential tensile strength
|
|
ISO/IEC 17025:2005
|
General requirements for the competence of testing and calibration laboratories
|
|
ISO 7432:2002
|
Glass-reinforced thermosetting plastics (GRP) pipes and fittings Test methods to prove the design of locked socket-and-spigot joints, including double-socket joints, with elastomeric seals
|
|
AWWA M45 : 3
|
FIBERGLASS PIPE DESIGN
|
|
ISO 7511:1999
|
Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the leaktightness of the wall under short-term internal pressure
|
|
EN 681-1:1996/A3:2005
|
ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
|
|
ISO 527-4:1997
|
Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
|
|
ISO 7685:1998
|
Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of initial specific ring stiffness
|
|
ISO 10467:2004
|
Plastics piping systems for pressure and non-pressure drainage and sewerage Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
|
|
ANSI/AWWA C950:2013
|
FIBERGLASS PRESSURE PIPE
|
|
ISO 10928:2016
|
Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Methods for regression analysis and their use
|
|
ISO 2394:2015
|
General principles on reliability for structures
|
|
ISO 161-1:1996
|
Thermoplastics pipes for the conveyance of fluids Nominal outside diameters and nominal pressures Part 1: Metric series
|
|
ISO 8639:2016
|
Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods for leaktightness and proof of structural design of flexible joints
|
|
ISO 75-2:2013
|
Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
|
|
EN 681-2:2000/A2:2005
|
ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 2: THERMOPLASTIC ELASTOMERS
|
|
CEN/TS 14632:2012
|
Plastics piping systems for drainage, sewerage and water supply, pressure and non-pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Guidance for the assessment of conformity
|
|
ISO 527-5:2009
|
Plastics Determination of tensile properties Part 5: Test conditions for unidirectional fibre-reinforced plastic composites
|
|
ISO 3126:2005
|
Plastics piping systems Plastics components Determination of dimensions
|
|
ISO 11922-1:1997
|
Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series
|
|
ISO 8533:2003
|
Plastics piping systems for pressure and non-pressure drainage and sewerage Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin Test methods to prove the design of cemented or wrapped joints
|
|
ISO 2078:1993
|
Textile glass Yarns Designation
|
|
ISO 8483:2003
|
Glass-reinforced thermosetting plastics (GRP) pipes and fittings Test methods to prove the design of bolted flange joints
|
|
ISO 8513:2016
|
Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Test methods for the determination of the initial longitudinal tensile strength
|
|
ISO 10468:2003
|
Glass-reinforced thermosetting plastics (GRP) pipes Determination of the long-term specific ring creep stiffness under wet conditions and calculation of the wet creep factor
|
|
ISO 4200:1991
|
Plain end steel tubes, welded and seamless — General tables of dimensions and masses per unit length
|
|
ISO 10466:1997
|
Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Test method to prove the resistance to initial ring deflection
|
|
ISO 10471:2003
|
Glass-reinforced thermosetting plastics (GRP) pipes Determination of the long-term ultimate bending strain and the long-term ultimate relative ring deflection under wet conditions
|
|
ISO/TS 20656-1:2017
|
Plastics piping systems — General rules for structural design of glass-reinforced thermosetting plastics (GRP) pipes — Part 1: Buried pipes
|
|
ISO 18851:2015
|
Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes and fittings Test method to prove the structural design of fittings
|
|
EN 14364:2013
|
Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints
|
|
EN 1990:2002/A1:2005/AC:2010
|
EUROCODE - BASIS OF STRUCTURAL DESIGN
|
|
ISO 2531:2009
|
Ductile iron pipes, fittings, accessories and their joints for water applications
|
|
ISO 4633:2015
|
Rubber seals — Joint rings for water supply, drainage and sewerage pipelines — Specification for materials
|
|
EN 1796:2013
|
Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP)
|
|
ISO 7509:2015
|
Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of time to failure under sustained internal pressure
|
Important note : All end users must be registered with an Account prior to user licenses being assigned.