• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

CEI EN 61095 : 2010

Current
Current

The latest, up-to-date edition.

ELECTROMECHANICAL CONTACTORS FOR HOUSEHOLD AND SIMILAR PURPOSES
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-01-2010

INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Characteristics of contactors
6 Product information
7 Normal service, mounting and
  transport conditions
8 Constructional and performance
  requirements
9 Tests
Annex A (normative) - Terminal
        marking and distinctive
        number
Annex B (normative) - Test sequences
        and number of samples
Annex C (normative) - Description of
        a method for adjusting the
        load circuit
Annex D (normative) - Determination
        of short-circuit power-factor
Annex E (normative) - Measurement of
        creepage distances and
        clearances
Annex F (normative) - Correlation between
        the nominal voltage of the supply
        system and the rated impulse
        withstand voltage of a contactor
Annex G (normative) - Hot wire ignition
        test
Annex H (normative) - Degrees of protection
        of enclosed contactor
Annex I (normative) - Requirements and tests
        for equipment with protective separation
Annex ZA (normative) - Normative references to
         international publications with their
         corresponding European publications

Pertains to electromechanical air break contactors for household and similar purposes provided with main contacts intended to be connected to circuits the rated voltage of which does not exceed 440 V a.c. (between phases) with rated operational currents less than or equal to 63 A for utilization category AC-7a and 32 A for utilization categories AC-7b and AC-7c, and rated conditional short-circuit current less than or equal to 6 kA.

Committee
CT 17
DevelopmentNote
Classificazione CEI 17-41 (08/2001)
DocumentType
Standard
Pages
134
PublisherName
Comitato Elettrotecnico Italiano
Status
Current
Supersedes

Standards Relationship
IEC 61095:2009 Identical
EN 61095:2009 Identical

CEI 64-8/4 : 2012 LOW VOLTAGE ELECTRICAL INSTALLATIONS - PART 4: PROTECTION FOR SAFETY
CEI 64-8/5 : 2012 LOW VOLTAGE ELECTRICAL INSTALLATIONS - PART 5: ERECTION AND SELECTION OF ELECTRICAL EQUIPMENT

IEC 60112:2003+AMD1:2009 CSV Method for the determination of the proof and the comparative tracking indices of solid insulating materials
IEC 60028:1925 International standard of resistance for copper
IEC 60947-4-1:2009+AMD1:2012 CSV Low-voltage switchgear and controlgear - Part 4-1: Contactors and motor-starters - Electromechanical contactors and motor-starters
EN 60085:2008 Electrical insulation - Thermal evaluation and designation
IEC 60073:2002 Basic and safety principles for man-machine interface, marking and identification - Coding principles for indicators and actuators
EN 60073:2002 Basic and safety principles for man-machine interface, marking and identification - Coding principles for indicators and actuators
IEC 60050-151:2001 International Electrotechnical Vocabulary (IEV) - Part 151: Electrical and magnetic devices
IEC 60050-441:1984 International Electrotechnical Vocabulary (IEV) - Part 441: Switchgear, controlgear and fuses
IEC 60947-5-1 : 4.0 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-1: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - ELECTROMECHANICAL CONTROL CIRCUIT DEVICES
IEC 60695-2-11:2014 Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT)
EN 60099-1:1994/A1:1999 SURGE ARRESTERS - PART 1: NON-LINEAR RESISTOR TYPE GAPPED SURGE ARRESTERS FOR A.C. SYSTEMS
EN 60216 : 1990
EN 60947-1:2007/A2:2014 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 1: GENERAL RULES (IEC 60947-1:2007/A2:2014)
ISO 2039-2:1987 Plastics Determination of hardness Part 2: Rockwell hardness
EN 60112 : 2003 AMD 1 2009 METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS
IEC 60085:2007 Electrical insulation - Thermal evaluation and designation
EN 60447:2004 Basic and safety principles for man-machine interface, marking and identification - Actuating principles
IEC 60447:2004 Basic and safety principles for man-machine interface, marking and identification - Actuating principles
EN 60947-4-1 : 2010 AMD 1 2012 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-1: CONTACTORS AND MOTOR-STARTERS - ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS (IEC 60947-4-1:2009/A1:2012)
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
EN 60695-2-10:2013 Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure
IEC 60364-4-44:2007+AMD1:2015 CSV Low-voltage electrical installations - Part 4-44: Protection for safety - Protection against voltage disturbances and electromagnetic disturbances
IEC 60099-1:1991+AMD1:1999 CSV Surge arresters - Part 1: Non-linear resistor type gapped surge arresters for a.c. systems
IEC 60947-1:2007+AMD1:2010+AMD2:2014 CSV Low-voltage switchgear and controlgear - Part 1: General rules
IEC 60695-11-10:2013 Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
EN 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
EN 60068-2-78:2013 Environmental testing - Part 2-78: Tests - Test Cab: Damp heat, steady state
IEC 60050-826:2004 International Electrotechnical Vocabulary (IEV) - Part 826: Electrical installations
IEC 61180:2016 High-voltage test techniques for low-voltage equipment - Definitions, test and procedure requirements, test equipment
EN 61140:2016 Protection against electric shock - Common aspects for installation and equipment
EN 61180:2016 High-voltage test techniques for low-voltage equipment - Definitions, test and procedure requirements, test equipment
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
ISO 7000:2014 Graphical symbols for use on equipment Registered symbols
IEC 61140:2016 Protection against electric shock - Common aspects for installation and equipment
IEC 60695-2-10:2013 Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure
IEC 60445:2017 Basic and safety principles for man-machine interface, marking and identification - Identification of equipment terminals, conductor terminations and conductors
IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
EN ISO 2039-2 : 1999 PLASTICS - DETERMINATION OF HARDNESS - PART 2 - ROCKWELL HARDNESS
EN 60695-2-11:2014 Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT) (IEC 60695-2-11:2014)

View more information
£202.20
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.