HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 203: GAS-INSULATED METAL-ENCLOSED SWITCHGEAR FOR RATED VOLTAGES ABOVE 52 KV

Available format(s)

Hardcopy , PDF

Language(s)

English, English - Italian

Published date

01-01-2013

Publisher

Comitato Elettrotecnico Italiano

FOREWORD
1 General
2 Normal and special service conditions
3 Terms and definitions
4 Ratings
5 Design and construction
6 Type tests
7 Routine tests
8 Guide to the selection of switchgear
   and controlgear
9 Information to be given with enquiries,
   tenders and orders
10 Transport, storage, installation,
   operation and maintenance
11 Safety
12 Influence of the product on the environment
Annex A (normative) - Test procedure for dielectric
        test on three-phase encapsulated
        GIS, range II
Annex B (normative) - Methods for testing gas-insulated
        metal-enclosed switchgear under conditions
        of arcing due to an internal fault
Annex C (informative) - Technical and practical
        considerations of site testing
Annex D (informative) - Calculation of pressure rise
        due to an internal fault
Annex E (informative) - Information to be given with
        enquiries, tenders and orders
Annex F (informative) - Service continuity
Annex G (informative) - Insulation levels for GIS with
        rated voltages higher than 800 kV
Annex H (informative) - List of notes concerning
        certain countries
Bibliography
Annex ZA (normative) - Normative references to
         international publications with their
         corresponding European publications
Annex ZB (informative) - A-deviations

Describes requirements for gas-insulated metal-enclosed switchgear in which the insulation is obtained, at least partly, by an insulating gas other than air at atmospheric pressure, for alternating current of rated voltages above 52 kV, for indoor and outdoor installation, and for service frequencies up to and including 60 Hz.

Committee	CT 17
DevelopmentNote	Classificazione CEI 17-15. (08/2006) Supersedes CEI EN 60517. (05/2008) To be read in conjunction with CEI EN 62271-1. (06/2013)
DocumentType	Standard
Pages	86
PublisherName	Comitato Elettrotecnico Italiano
Status	Current
Supersedes	CEI EN 60517 : 1999 AMD 11 2000 CEI 17-15 : 3ED 1992

Standards	Relationship
EN 62271-203:2012	Identical
IEC 62271-203:2011	Identical

IEC 60480:2004	Guidelines for the checking and treatment of sulfur hexafluoride (SF<sub>6</sub>) taken from electrical equipment and specification for its re-use
IEC 62271-100:2008+AMD1:2012+AMD2:2017 CSV	High-voltage switchgear and controlgear - Part 100: Alternating-current circuit-breakers
EN 60044-2:1999/A2:2003	INSTRUMENT TRANSFORMERS - PART 2: INDUCTIVE VOLTAGE TRANSFORMERS
IEC 61672-2:2013+AMD1:2017 CSV	Electroacoustics - Sound level meters - Part 2: Pattern evaluation tests
IEC 60038:2009	IEC standard voltages
IEC 60270:2000+AMD1:2015 CSV	High-voltage test techniques - Partial discharge measurements
EN 50052:2016	High-voltage switchgear and controlgear - Gas-filled cast aluminium alloy enclosures
EN 60376:2005	Specification of technical grade sulfur hexafluoride (SF6) for use in electrical equipment
CLC/TR 62271-303 : 2009	HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 303: USE AND HANDLING OF SULPHUR HEXAFLUORIDE (SF[6])
EN 61264:1998/corrigendum:2000	CERAMIC PRESSURIZED HOLLOW INSULATORS FOR HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR
IEC 62271-207:2012	High-voltage switchgear and controlgear - Part 207: Seismic qualification for gas-insulated switchgear assemblies for rated voltages above 52 kV
IEC 62155:2003	Hollow pressurized and unpressurized ceramic and glass insulators for use in electrical equipment with rated voltages greater than 1 000 V
EN 62271-1:2017	High-voltage switchgear and controlgear - Part 1: Common specifications for alternating current switchgear and controlgear
EN ISO 3231:1997	Paints and varnishes - Determination of resistance to humid atmospheres containing sulfur dioxide (ISO 3231:1993)
IEEE 1416 : 1998	INTERFACE OF NEW GAS INSULATED EQUIPMENT IN EXISTING GAS INSULATED SUBSTATIONS
CEI 42-3 : 2ED 1997
IEC 60050-471:2007	International Electrotechnical Vocabulary (IEV) - Part 471: Insulators
IEC 60050-441:1984	International Electrotechnical Vocabulary (IEV) - Part 441: Switchgear, controlgear and fuses
IEC 60044-2:1997+AMD1:2000+AMD2:2002 CSV	Instrument transformers - Part 2 : Inductive voltage transformers
IEC TS 60815-2:2008	Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 2: Ceramic and glass insulators for a.c. systems
EN 62271-102:2002/AC:2014	HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 102: ALTERNATING CURRENT DISCONNECTORS AND EARTHING SWITCHES (IEC 62271-102:2001/A2:2013)
IEC 60068-2-11:1981	Basic environmental testing procedures - Part 2-11: Tests - Test Ka: Salt mist
EN 60480:2004	Guidelines for the checking and treatment of sulphur hexafluoride (SF6) taken from electrical equipment and specification for its re-use
IEC 62271-209:2007	High-voltage switchgear and controlgear - Part 209: Cable connections for gas-insulated metal-enclosed switchgear for rated voltages above 52 kV - Fluid-filled and extruded insulation cables - Fluid-filled and dry-type cable-terminations
IEC TR 62271-300:2006	High-voltage switchgear and controlgear - Part 300: Seismic qualification of alternating current circuit-breakers
CEI 10-7 : 1ED 1997
IEC 60376:2005	Specification of technical grade sulfur hexafluoride (SF<sub>6</sub>) for use in electrical equipment
EN 50064 : 1989 COR 2007	WROUGHT ALUMINIUM AND ALUMINIUM ALLOY ENCLOSURES FOR GAS-FILLED HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR
CEI 17-1 : 5ED 1998
EN 60270:2001/A1:2016	HIGH-VOLTAGE TEST TECHNIQUES - PARTIAL DISCHARGE MEASUREMENTS (IEC 60270:2000/A1:2015)
IEEE C37.122.1-2014 REDLINE	IEEE Guide for Gas-Insulated Substations Rated Above 52 kV
IEC 60044-1:1996+AMD1:2000+AMD2:2002 CSV	Instrument transformers - Part 1: Current transformers
IEC 61462:2007	Composite hollow insulators - Pressurized and unpressurized insulators for use in electrical equipment with rated voltage greater than 1 000 V - Definitions, test methods, acceptance criteria and design recommendations
IEC 62271-1:2017	High-voltage switchgear and controlgear - Part 1: Common specifications for alternating current switchgear and controlgear
IEEE C37.24-2003	IEEE Guide for Evaluating the Effect of Solar Radiation on Outdoor Metal-Enclosed Switchgear
EN 62271-209:2007	High-voltage switchgear and controlgear - Part 209: Cable connections for gas-insulated metal-enclosed switchgear for rated voltages above 52 kV - Fluid-filled and extruded insulation cables - Fluid-filled and dry-type cable-terminations
IEC 60141-1:1993	Tests on oil-filled and gas-pressure cables and their accessories - Part 1: Oil-filled, paper or polypropylene paper laminate insulated, metal-sheathed cables and accessories for alternating voltages up to and including 500 kV
EN 60044-1:1999/A2:2003	INSTRUMENT TRANSFORMERS - PART 1: CURRENT TRANSFORMERS
CEI 38-1 : 3ED 1998
EN 60068-2-11:1999	Environmental testing - Part 2: Tests - Test Ka: Salt mist
CEI 38-2 : 3ED 1998
IEC 60060-1:2010	High-voltage test techniques - Part 1: General definitions and test requirements
IEC 60071-1:2006+AMD1:2010 CSV	Insulation co-ordination - Part 1: Definitions, principles and rules
EN 50068 : 1991 COR 2007	WROUGHT STEEL ENCLOSURES FOR GAS FILLED HIGH VOLTAGE SWITCHGEAR AND CONTROLGEAR
CEI 36-2 : 3ED 1987
IEC 62067 : 2.0EN+(REDLINE+VERSION)	POWER CABLES WITH EXTRUDED INSULATION AND THEIR ACCESSORIES FOR RATED VOLTAGES ABOVE 150 KV (U[M] = 170 KV) UP TO 500 KV (U[M] = 550 KV) - TEST METHODS AND REQUIREMENTS
IEC TS 60815-1:2008	Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 1: Definitions, information and general principles
IEC TS 60815-3:2008	Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 3: Polymer insulators for a.c. systems
IEC 62271-102:2001+AMD1:2011+AMD2:2013 CSV	High-voltage switchgear and controlgear - Part 102: Alternatingcurrent disconnectors and earthing switches
ISO 3231:1993	Paints and varnishes — Determination of resistance to humid atmospheres containing sulfur dioxide
EN 50089 : 92 AMD 1 94	SPECIFICATION FOR CAST RESIN PARTITIONS FOR METAL-ENCLOSED GAS-FILLED HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR

View more information

£268.79

Excluding VAT

Product format

I agree to the DRM document license rules apply against the PDF selection made.

Please confirm that you agree to the document license rules for this document.

I agree to the document license rules .

Please confirm that you agree to the document license rules for this document.

Access your standards online with a subscription

Features

Simple online access to standards, technical information and regulations.
Critical updates of standards and customisable alerts and notifications.
Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

Get in touch with us

Log into your Account

CEI EN 62271-203 : 2013

Current

Table of Contents

Abstract

General Product Information

International Equivalents

Standards Referencing This Book

Category

Subcategory

Access your standards online with a subscription