CEN/TS 13001-3-1:2004/AC:2006
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
CRANES - GENERAL DESIGN - PART 3-1: LIMIT STATES AND PROOF OF COMPETENCE OF STEEL STRUCTURES
01-06-2012
12-01-2013
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 General
4.1 Materials
4.1.1 Structural members
4.1.2 Connecting devices
4.2 Bolt connections
4.2.1 General
4.2.2 Shear and bearing connections
4.2.3 Slip resistant connections
4.2.4 Connections loaded in tension
4.3 Pin connections
4.4 Welded connections
4.5 Proofs of structural members and connections
5 Proof of static strength
5.1 General
5.2 Limit design stresses and forces
5.2.1 General
5.2.2 Limit design stress in structural members
5.2.3 Limit design forces in bolt connections
5.2.4 Limit design forces in pins
5.2.5 Limit design stresses in welded connections
5.3 Execution of the proof
5.3.1 Proof for structural members
5.3.2 Proof for bolt connections
5.3.3 Proof for pin connections
5.3.4 Proof for welded connections
6 Proof of fatigue strength
6.1 General
6.2 Limit design stresses
6.2.1 Characteristic values of the stress range
6.2.2 Weld quality
6.2.3 Effect of test loads
6.2.4 Requirements for fatigue testing
6.3 Classes S of stress history parameter s
6.3.1 Simplified method based on service conditions
6.3.2 Selection based on experience
6.4 Execution of the proof
6.5 Determination of the permissible stress range
6.5.1 Applicable methods
6.5.2 Direct use of stress history parameter
6.5.3 Use of class S
7 Proof of static strength of hollow section girder joints
8 Proof of elastic stability
Annex A (normative) Values of inverse slope m of sigma/N -
curve and the value of the characteristic
stress range delta sigma[c], delta tau[c]
Annex B (informative) Guidance for selection of classes S due
to experience
Annex C (normative) Calculated values of permissible stress
range delta sigma[Rd]
Annex D (normative) Design weld stress sigma[W,Sd] and
tau[W,Sd]
D.1 Butt joint
D.2 Fillet weld and groove weld with uniform distributed
load
D.3 Relevant distribution length under punctiform load
Annex E (informative) Hollow Sections
Annex F (informative) Selection of a suitable set of crane
standards for a given application
Bibliography
Describes general conditions, requirements and methods to prevent mechanical hazards of cranes by design and theoretical verification.
Committee |
TC 147
|
DevelopmentNote |
To be used in conjunction with EN 13001-1 and EN 13001-2. (01/2005)
|
DocumentType |
Standard
|
PublisherName |
Comite Europeen de Normalisation
|
Status |
Superseded
|
SupersededBy |
Standards | Relationship |
UNI CEN/TS 13001-3-1 : 2005 | Identical |
DD CEN/TS 13001-3-1 : 2004 | Identical |
UNE-CEN/TS 13001-3-1:2006 EX | Identical |
NBN CEN/TS 13001-3-1 : 2005 | Identical |
NF CEN/TS 13001-3-1 : 2005 XP | Identical |
NEN NPR CEN/TS 13001-3-1 : 2005 C1 2007 | Identical |
I.S. CEN TS 13001-3-1:2005 | Identical |
BS EN 81-43:2009 | Safety rules for the construction and installation of lifts. Special lifts for the transport of persons and goods Lifts for cranes |
DIN EN 81-43:2010-05 | Safety rules for the construction and installation of lifts - Special lifts for the transport of persons and goods - Part 43: Lifts for cranes |
04/30058232 DC : DRAFT OCT 2004 | EN 12999 A2 - CRANES - LOADER CRANES |
UNE-EN 14985:2012 | Cranes - Slewing jib cranes |
DIN EN 14985 E : 2012 | CRANES - SLEWING JIB CRANES |
EN 13135-2:2004+A1:2010 | Cranes - Equipment - Part 2: Non-electrotechnical equipment |
09/30202029 DC : 0 | BS EN 13852-1 - CRANES - OFFSHORE CRANES - PART 1: GENERAL-PURPOSE OFFSHORE CRANES |
11/30235009 DC : 0 | BS EN 13852-1 - CRANES - OFFSHORE CRANES - PART 1: GENERAL PURPOSE OFFSHORE CRANES |
UNI EN 81-43 : 2009 | SAFETY RULES FOR THE CONSTRUCTION AND INSTALLATION OF LIFTS - SPECIAL LIFTS FOR THE TRANSPORT OF PERSONS AND GOODS - PART 43: LIFTS FOR CRANES |
I.S. EN 14492-2:2006 | CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS |
BS EN 15056 : 2006 | CRANES - REQUIREMENTS FOR CONTAINER HANDLING SPREADERS |
UNE-EN 13135-2:2005 | Cranes - Equipment - Part 2: Non-electrotechnical equipment |
I.S. EN 15056:2006 | CRANES - REQUIREMENTS FOR CONTAINER HANDLING SPREADERS |
I.S. EN 14492-1:2006 | CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 1: POWER DRIVEN WINCHES |
DIN EN 14492-1:2010-06 | Cranes - Power driven winches and hoists - Part 1: Power driven winches (includes Amendment A1:2009) |
I.S. EN 13852-1:2013 | CRANES - OFFSHORE CRANES - PART 1: GENERAL - PURPOSE OFFSHORE CRANES |
I.S. EN 14985:2012 | CRANES - SLEWING JIB CRANES |
07/30161753 DC : 0 | BS EN 15011 - CRANES - BRIDGE AND GANTRY CRANES |
17/30348210 DC : 0 | BS ISO 19426-3 - STRUCTURES FOR MINE SHAFTS - PART 3: SINKING STAGES |
I.S. CEN TS 13001-3-2:2005 | CRANES - GENERAL DESIGN - PART 3-2: LIMIT STATES AND PROOF OF COMPETENCE OF WIRE ROPES IN REEVING SYSTEMS |
ISO 19426-3:2018 | Structures for mine shafts — Part 3: Sinking stages |
BS EN 13135-2 : 2004 | CRANES - EQUIPMENT - PART 2: NON-ELECTROTECHNICAL EQUIPMENT |
UNI EN 13135-2 : 2010 | CRANES - EQUIPMENT - PART 2: NON-ELECTROTECHNICAL EQUIPMENT |
UNI EN 15056 : 2009 | CRANES - REQUIREMENTS FOR CONTAINER HANDLING SPREADERS |
UNI EN 14985 : 2012 | CRANES - SLEWING JIB CRANES |
UNI EN 13852-1 : 2013 | CRANES - OFFSHORE CRANES - PART 1: GENERAL-PURPOSE OFFSHORE CRANES |
UNI EN 14492-2 : 2009 | CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS |
UNI EN 14492-1 : 2009 | CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 1: POWER DRIVEN WINCHES |
10/30228230 DC : 0 | BS EN 13001-2 - CRANES - GENERAL DESIGN - PART 2: LOAD ACTIONS |
I.S. EN 81-43:2009 | SAFETY RULES FOR THE CONSTRUCTION AND INSTALLATION OF LIFTS - SPECIAL LIFTS FOR THE TRANSPORT OF PERSONS AND GOODS - PART 43: LIFTS FOR CRANES |
PREN 13852-1 : DRAFT 2011 | CRANES - OFFSHORE CRANES - PART 1: GENERAL PURPOSE OFFSHORE CRANES |
DIN EN 14985:2012-05 | Cranes - Slewing jib cranes |
DIN EN 15056 E : 2010 | CRANES - REQUIREMENTS FOR CONTAINER HANDLING SPREADERS |
DIN EN 13852-1:2014-01 | Cranes - Offshore cranes - Part 1: General-purpose offshore cranes |
BS EN 14985:2012 | Cranes. Slewing jib cranes |
BS EN 14492-1 : 2006 | CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 1: POWER DRIVEN WINCHES |
DIN EN 15056:2010-02 | Cranes - Requirements for container handling spreaders (includes Amendment A1:2009) |
UNE-EN 13852-1:2014 | Cranes - Offshore cranes - Part 1: General-purpose offshore cranes |
EN 81-43:2009 | Safety rules for the construction and installation of lifts - Special lifts for the transport of persons and goods - Part 43: Lifts for cranes |
EN 14985:2012 | Cranes - Slewing jib cranes |
EN 15056:2006+A1:2009 | Cranes - Requirements for container handling spreaders |
EN 14492-1:2006+A1:2009/AC:2010 | CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 1: POWER DRIVEN WINCHES |
EN 13852-1:2013 | Cranes - Offshore cranes - Part 1: General-purpose offshore cranes |
EN 14492-2:2006+A1:2009/AC:2010 | CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS |
10/30194893 DC : 0 | BS EN 13135-2:2004/A1 - CRANES - EQUIPMENT - PART 2: NON-ELECTROTECHNICAL EQUIPMENT |
07/30164729 DC : 0 | BS EN 12999 - CRANES - LOADER CRANES |
DD CEN/TS 13001-3-2:2004 | Cranes. General design Limit states and proof of competence of wire ropes in reeving systems |
DIN EN 14492-2:2016-08 (Draft) | CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS |
DIN EN 13135-2:2011-07 | CRANES - EQUIPMENT - PART 2: NON-ELECTROTECHNICAL EQUIPMENT |
DIN EN 14492-1:2015-05 (Draft) | Cranes - Power driven winches & hoists - part 1 power driven winches; German and English version prEN 14492-1:2015 |
BS EN 13852-1:2013 | Cranes. Offshore cranes General-purpose offshore cranes |
BS EN 14492-2 : 2006 | CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS |
DIN EN 14492-2:2010-05 | CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS |
EN 10113-2 : 1993 | HOT-ROLLED PRODUCTS IN WELDABLE FINE GRAIN STRUCTURAL STEELS - DELIVERY CONDITIONS FOR NORMALIZED/NORMALIZED ROLLED STEELS |
ISO 2553:2013 | Welding and allied processes Symbolic representation on drawings Welded joints |
EN 10149-1:2013 | Hot rolled flat products made of high yield strength steels for cold forming - Part 1: General technical delivery conditions |
ISO 4306-1:2007 | Cranes — Vocabulary — Part 1: General |
EN 10164:2004 | Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions |
EN 10149-2:2013 | Hot rolled flat products made of high yield strength steels for cold forming - Part 2: Technical delivery conditions for thermomechanically rolled steels |
EN 10025:1990/A1:1993 | HOT ROLLED PRODUCTS OF NON-ALLOY STRUCTURAL STEELS - TECHNICAL DELIVERY CONDITIONS |
EN 12345 : 1998 | WELDING - MULTILINGUAL TERMS FOR WELDED JOINTS WITH ILLUSTRATIONS |
ISO 9013:2017 | Thermal cutting — Classification of thermal cuts — Geometrical product specification and quality tolerances |
API 2A : 1986 | RECOMMENDED PRACTICE FOR PLANNING, DESIGNING AND CONSTRUCTING FIXED OFFSHORE PLATFORMS |
EN 10045-1 : 1990 | METALLIC MATERIALS - CHARPY IMPACT TEST - PART 1: TEST METHOD |
ISO 5817:2014 | Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections |
EN 10137-2 : 1995 | PLATES AND WIDE FLATS MADE OF HIGH YIELD STRENGTH STRUCTURAL STEELS IN THE QUENCHED AND TEMPERED OR PRECIPITATION HARDENED CONDITIONS - DELIVERY CONDITIONS FOR QUENCHED AND TEMPERED STEELS |
EN 13001-2:2014 | Crane safety - General design - Part 2: Load actions |
EN 10113-1 : 1993 | HOT ROLLED PRODUCTS IN WELDABLE FINE GRAIN STRUCTURAL STEELS - GENERAL DELIVERY CONDITIONS |
EN ISO 12100-1:2003/A1:2009 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY |
EN 13001-1:2015 | Cranes - General design - Part 1: General principles and requirements |
EN 22553:1994 | Welded, brazed and soldered joints - Symbolic representation on drawings (ISO 2553:1992) |
ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
EN ISO 12100-2:2003/A1:2009 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES |
ISO 286-2:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts |
EN ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013) |
ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
1998/37/EC : 1998 | DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 22 JUNE 1998 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO MACHINERY |
EN 1990:2002/A1:2005/AC:2010 | EUROCODE - BASIS OF STRUCTURAL DESIGN |
EN ISO 9013:2017 | Thermal cutting - Classification of thermal cuts - Geometrical product specification and quality tolerances (ISO 9013:2017) |
EN 1070 : 1998 | SAFETY OF MACHINERY - TERMINOLOGY |
EN 10149-3:2013 | Hot rolled flat products made of high yield strength steels for cold forming - Part 3: Technical delivery conditions for normalized or normalized rolled steels |
EN 25817 : 1992 | ARC WELDED JOINTS IN STEEL - GUIDANCE ON QUALITY LEVELS FOR IMPERFECTIONS |
EN 1993-1-1:2005/A1:2014 | EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS |
ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread |
EN 10113-3 : 1993 | HOT ROLLED PRODUCTS IN WELDABLE FINE GRAIN STRUCTURAL STEELS - DELIVERY CONDITIONS FOR THERMOMECHANICAL ROLLED STEELS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.